Instruction Manual

19
8. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (g. 5):
the appliance is now ready to rinse with fresh water. Empty
the container used to collect the descaler solution. Extract
the water tank, empty, rinse under running water, ll
with fresh water up to the MAX level and put back in the
appliance;
9. "POSITION 2l CONTAINER PRESS OK TO START RINSING":
Place the container used to collect the descaler solution
empty under the coee spouts and hot water/steam spout
(g. 8) and press the selector corresponding to " OK";
10 Hot water is delivered rst from the coee spouts, then
from the hot water/steam spout and "RINSING UNDER-
WAY" is displayed;
11. When the water in the tank has run out, empty the con-
tainer used to collect the rinsing water;
40
12. (If the lter is installed)
"INSERT FILTER INTO
ITS HOUSING" (g. 40).
Press the selector cor-
responding to "NEXT>"
and extract the water
tank. Replace the water
softener lter if removed
previously;
13. "RINSE AND FILL WATER
TANK UP TO MAX LEVEL"
(g. 5): Fill the tank up to
the MAX level with fresh
water;
14. "INSERT WATER TANK" (g. 6): Put the water tank back in
the appliance;
15. "POSITION 2l CONTAINER PRESS OK TO START RINSING":
Place the container used to collect the descaler solution
empty under the hot water/steam spout (g. 8) and press
the selector corresponding to " OK";
16. Hot water is delivered from the hot water/steam spout and
"RINSING UNDERWAY, PLEASE WAIT" is displayed;
17. "EMPTY DRIP TRAY" (g. 39): At the end of the second
rinse, remove, empty and replace the drip tray (A14) and
grounds container (A10). Press the selector corresponding
to "NEXT>";
18. "DESCALE COMPLETE": to conrm, press the selector corre-
sponding to “ OK";
19. "FILL TANK WITH FRESH WATER": empty the container
used to collect the rinse water, remove the water tank and
ll with fresh water up to the MAX level, then put back in
the appliance.
Descaling is complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A10) to contain water.
• If the water tank has not been lled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been complete-
ly eliminated from the machine's internal circuits. Before
starting rinsing, remember to empty the drip tray;
• The appliance may request descaling cycles at very short
intervals. This is normal and due to the appliance’s ad-
vanced control system.
16. SETTING WATER HARDNESS
The "DESCALING NEEDED  PRESS OK TO START ~45MIN
" message is displayed after a period of time established
according to water hardness.
The machine is set by default for a hardness value of "4". The
machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
16.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
16.2 Setting water hardness
1. Press the selector (B2) corresponding to the " " symbol
(B5) to enter the menu;
2. Scroll through the menu items by pressing the selector
corresponding to "NEXT>" until " WATER HARDNESS"
appears on the display;
3. Press the selector corresponding to " WATER
HARDNESS";
4. "WATER HARDNESS, CURRENT UNDERLINED": Press the se-
lector corresponding to the required level (Level 1 = soft
water; Level 4 = very hard water);
soft water LEV.1
slightly hard water LEV.2
hard water LEV.3
very hard water LEV.4