Instruction Manual

14
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam
connection nozzle (A9) with a sponge (g. 22).
Please note!
• To prepare a number of cappuccinos or milk-based coees,
clean the milk container after you have prepared the last
beverage only. To proceed with making the next beverag-
es, when the "CLEAN message is displayed, press the selec-
tor corresponding to “ ESC”.
If you do not clean the milk container, the symbol appears
on the display to remind you that it needs cleaning.
• The milk container can be kept in the refrigerator.
• In some cases, before cleaning you must wait for the appli-
ance to heat up.
9. DELIVERING HOT WATER
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Press the selector (B2) corresponding to the " " symbol
(B3) to enter the menu;
4. Press the selector corresponding to the "NEXT>" symbol
until "HOT WATER" is displayed;
5. Press the selector corresponding to " HOT WATER". The cor-
responding image appears on the display (B1), together
with a progress bar which lls gradually as preparation
proceeds;
6. The machine delivers hot water, then delivery stops auto-
matically. To interrupt hot water delivery manually, press
the selector corresponding to " STOP" again.
Please note!
• If "Energy Saving" mode is active, you may have to wait a few
seconds before hot water is delivered.
• Preparation of each coee can be customised (see sec-
tions”12. Customising the beverages ”and “13. Memoris-
ing your personal prole”).
10. STEAM DELIVERY
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Press the selector (B2) corresponding to the " " symbol
(B3) to enter the menu;
4. Press the selector (B2) corresponding to the "NEXT>" sym-
bol until "STEAM" appears on the display;
5. Press the selector corresponding to "STEAM". The corre-
sponding image appears on the display (B1), together with
a progress bar which lls gradually as preparation proceeds
and after a few seconds, steam to heat the liquid is deliv-
ered from the cappuccino maker;
6. When the required temperature or froth level is obtained,
interrupt steam delivery by pressing the selector corre-
sponding to " STOP".
Important!
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
Please note!
If "Energy Saving" mode is active, you may have to wait a few
seconds before the hot water is delivered.
10.1 Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow move-
ments in an upward direction.
• To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
10.2 Cleaning the hot water/steam spout after
use
Always clean the hot water/steam spout (C6) after use to avoid the
build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and de-
liver a little water (see section “9. Delivering hot
water”). To interrupt hot water delivery manually, press the
selector (B2) corresponding to " STOP".
2. Wait a few minutes for the hot water/steam spout to cool
down, then extract (g. 17) by pressing the release button
(C7). Hold the spout with one hand and with the other,
turn the cappuccino maker and pull it downwards (g. 23).
3. Also remove the steam connection nozzle by pulling it
downwards (g. 24).
4. Check the hole in the connection nozzle is not blocked. If
necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
6. Insert the connection nozzle and cappuccino maker on the
spout by pushing them upwards and turning them clock-
wise until they are attached.
11. TEA FUNCTION
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Put a tea bag in the cup, then place the cup under the spout
(as close as possible to avoid splashes);