Instruction Manual

8
2.3 Description of the accessories (page 2 - C )
C1. “Total Hardness Test" indicator paper (attached to page 2
of the English instructions)
C2. Pre-ground coee measure
C3. Descaler
C4. Water softener lter (certain models only)
C5. Cleaning brush
C6. Hot water spout
C7. Power cord
2.4 "Cleaning the milk container" (page 2 - D)
D1. Froth adjustment and CLEAN dial
D2. Milk container lid
D3. Milk container
D4. Milk intake tube
D5. Frothed milk spout (adjustable)
3. SETTING UP THE APPLIANCE
Please note!
• Coee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the instructions in section “14. Setting water
hardness”.
1. Plug the power cord (C7) connector into the socket (A20) at
the back of the appliance and connect the appliance to the
mains electricity supply (g. 1). Make sure the main switch
(A21) at the back of the appliance is pressed (g. 2);
2. "SELECT LANGUAGE": Press the selector (B2) correspond-
ing to "NEXT>" until the required language appears on the
display (B1), then press the selector corresponding to the
language.
Follow the instructions indicated on the appliance display:
3. "FILL TANK WITH FRESH WATER": remove the water tank
(A16) (g. 3), open the lid (A15) (g. 4), ll to the MAX line
(marked on the inside of the tank) with fresh water (g. 5),
close the lid and put the tank back in the appliance (g. 6);
4. "INSERT WATER SPOUT": Check that the hot water/steam
spout (C6) is inserted on the connection nozzle (A9) (g. 7)
and place a container holding a minimum of 100 ml under-
neath (g. 8);
5. WATER CIRCUIT EMPTY PRESS OK TO START: press the se-
lector corresponding to " OK" to conrm. The appliance
delivers hot water from the spout (g. 8) then goes o
automatically.
The coee machine is now ready for normal use.
Please note!
• The rst time you use the appliance, you need to make 4-5
cappuccinos before it starts to give satisfactory results.
• The rst time you use the machine, the water circuit is
empty and the appliance could be very noisy. The noise
becomes less as the circuit lls.
• When making the rst 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
• To improve the performance of your appliance, we recom-
mend installing a water softener lter (C4) as described
in section “15. Water softener lter”. If your model is not
provided with a lter, you can request one from De'Longhi
Customer Services.
4. TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch
(A21) is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
• To turn the appliance on, press the button (A7-g.
9). The message "HEATING UP UNDERWAY PLEASE WAIT"
appears on the display.
• When heating is complete, the message changes to:
"RINSING UNDERWAY, PLEASE WAIT"; as well as heating
the boiler, this also heats the internal circuits by circulating
hot water.
The appliance is at temperature when the main screen (home-
page) appears.
5. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
• To turn the appliance o, press the button (A7) (g.
9).
• The message "TURNING OFF UNDERWAY, PLEASE WAIT"
is displayed, then the appliance performs a rinse cycle and
goes o (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• rst turn the appliance o by pressing the button
(g. 9);
• release the main switch (A21) at the back of the appliance
(g. 2).
Important!
Never press the main switch while the appliance is on.