Instruction Manual

9
6. MENU SETTINGS
6.1 Rinsing
Use this function to deliver hot water from the coee spouts
(A8) and hot water spout (C6), if inserted, to clean and heat the
appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coee and hot water spouts (g. 8).
To enable the function, proceed as follows:
1. Press the selector (B2) corresponding to the " " symbol
(B5) to enter the menu;
2. Press the selector corresponding to " RINSING";
3. After a few seconds, hot water is delivered rst from the
coee spouts, then from the hot water spout (if inserted)
to clean and heat the appliance’s internal circuit. "RINSING
UNDERWAYPLEASE WAIT" appears on the display, togeth-
er with a progress bar which lls gradually as preparation
proceeds;
4. To interrupt rinsing, press the selector corresponding to "
STOP" or wait for rinsing to stop automatically.
Please note!
• If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning, it is normal for the coee grounds container
(A10) to contain water.
6.2 Descaling
For instructions on descaling, see section “13. Descaling”.
6.3 Water lter
For instructions on how to install the lter (C4), see section”15.
Water softener lter”.
6.4 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage.
1. Press the selector (B2) corresponding to the " " symbol
(B5) to enter the menu;
2. Scroll through the menu items by pressing the selector cor-
responding to "NEXT>" until " BEVERAGES SETTINGS"
appears on the display;
3. Press the selector corresponding to " BEVERAGES
SETTINGS". The values for the rst beverage appear on the
display;
4. The reference user prole is highlighted on the display. The
values are displayed on vertical bars. The default value is
indicated by the symbol, while the current value is
highlighted by the solid part of the vertical bar;
5. To go back to the settings menu, press the selector corre-
sponding to " ESC". To scroll through and display the
beverages, press the selector corresponding to "NEXT>";
6. To reset the default values for the beverage displayed,
press the selector corresponding to " RESET";
7. "CONFIRM RESET?": to conrm press the selector corre-
sponding to " OK " (to cancel, press the selector corre-
sponding to " ESC");
8. "DEFAULT VALUES SET": press " OK ".
The beverage has been reset to the default values. Proceed with
the other beverages or go back to the homepage by pressing the
arrow corresponding to " ESC" twice.
Please note!
• To change the beverages in another prole, go back to the
homepage, select the required prole (B11) and repeat the
procedure.
• To reset all the beverages in the prole to the default val-
ues, see section “7. Making coee”.
6.5 Auto-o (standby)
Auto-o can be set so that the appliance goes o after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-o, proceed as follows:
1. Press the selector (B2) corresponding to the " " symbol
(B5) to enter the menu;
2. Scroll through the menu items by pressing the selector cor-
responding to "NEXT>" until " AUTO-OFF" appears on
the display;
3. Press the selector corresponding to " AUTO-OFF";
4. Select the required time interval by pressing the selec-
tion arrows corresponding to (increase) or
(decrease);
5. To conrm, press the selector corresponding to " OK";
6. Press the selector corresponding to " ESC" to go back to
the homepage.
Auto-o is now programmed.
6.6 Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
1. Press the selector (B2) corresponding to the " " symbol
(B5) to enter the menu;
2. Scroll through the menu items by pressing the selector cor-
responding to "NEXT>" until " ENERGY SAVING" appears
on the display;
3. Press the selector corresponding to "ENERGY SAVING" to
disable ( ) or enable ( ) the function.
4. Press the selector corresponding to " ESC" to go back to
the homepage.
The corresponding symbol appears on the display to indicate
that the function has been enabled.