User's Manual
15
Please note!
• Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
ETC.). Their meaning is explained in section “24. Displayed
messages”.
• For hotter coee, see section “9.6 Tips for a hotter coee”.
• If the coee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in sections “9.5
Adjusting the coee mill” and “25. Troubleshooting”.
• Preparation of each coee can be customised (see sections
“16. Customising the beverages E” and “17. Memorising
your personal prole”).
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the rst coee is delivered.
9.4 Making coee using pre-ground coee
Important!
• Never add pre-ground coee when the machine is o or it
could spread through the inside of the machine and dirty it.
This could damage the appliance.
• Never use more than 1 level measure (C2) or it could dirty
the inside of the coee machine or block the funnel (A4).
Please note!
If you use pre-ground coee, you can only make one cup of cof-
fee at a time.
1. Press " AROMA" (B6) repeatedly until " " (pre-
ground) appears on the display (B).
2. Open the pre-ground coee funnel lid (A2).
3. Make sure the funnel (A4) is not blocked, then add one level
measure of pre-ground coee (g. 14).
4. Place a cup under the coee spouts (A8) (g. 13).
5. Then select your required coee (ESPRESSO, COFFEE, LONG,
AMERICANO);
6. Preparation begins. An image of the selected beverage ap-
pears on the display, together with a progress bar which
gradually lls as preparation proceeds.
Please note!
• While the machine is making coee, delivery can be inter-
rupted at any moment by pressing " ".
• As soon as delivery has ended, to increase the quantity of
coee in the cup, just press " ". When the re-
quired quantity is reached, press " ".
Once the coee has been made, the appliance is ready to make
the next beverage.
Important! Making LONG coee :
Halfway through preparation, the message "ADD PREGROUND
COFFEE, MAXIMUM ONE MEASURE" IS DISPLAYED. Add one
level measure of pre-ground coee and press " ".
Please note!
• Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
ETC.). Their meaning is explained in section “24. Displayed
messages”.
• For hotter coee, see section “9.6 Tips for a hotter coee”.
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the rst coee is delivered.
9.5 Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting the
grinding adjustment dial (A5 - g. 11).
Please note!
The grinding adjustment dial must only be turned when the
coee mill is in operation during the initial phase of coee
preparation.
If the coee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coee, turn
one click anticlockwise towards 1 (do
not turn more than one click at a time
otherwise the coee could be delivered
a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.6 Tips for a hotter coee
For hotter coee, you should:
• perform a rinse cycle by selecting the "Rinsing" function in the
settings menu (section “8.1 Rinsing ”);
• warm the cups with hot water using the hot water function
(see section “12. Delivering hot water”);
• increase the coee temperature in the settings menu (see
section “8.10 Coee temperature ”).
10. MAKING CAPPUCCINOS AND MILKBASED
COFFEES
Please note!
To avoid milk with poor froth or large bubbles, always clean the
milk container lid (D2) and hot water connection nozzle (A9) as
described in sections “10.4 Cleaning the milk container after
use”, “18.10 Cleaning the milk container” and “18.11 Cleaning
the hot water/steam connection nozzle”.