Instruction Manual

17
4. Press the PROG icon. The appliance starts programming;
5. As soon as the coee in the cup reaches the required level,
press the STOP icon again.
The quantity set has now been programmed.
Please note!
• To cancel programming of“My LONG coee”, press the
EXIT PROG icon.
“My LONG coee” can be customised in all proles (see
“Memorising your personal prole” on page 17).
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Do not leave the appliance unattended while delivering hot
water or steam. The spout becomes hot during delivery. Hold
by the handle only.
Please note!
If Energy Saving is active, you may have to wait a few seconds
before hot water and steam are delivered.
Delivering hot water
1. Check that the hot water spout is attached correctly.
2. Place a container under the water spout (as close as
possible to avoid splashes) (g. 4).
3 Press the icon (g. 37).
4. Hot water delivery begins and then stops automatically.
A progress bar lls gradually as preparation proceeds. To
interrupt delivery of the hot water manually, press the
STOP icon again.
Please note!
The quantity of hot water can be customised in all
proles (see “Memorising your personal prole” on page
17).
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 8.45
.oz/250 ml of hot water. To modify these quantities, proceed
as follows:
1. Check that the hot water spout is attached correctly.
2. Position a container under the spout.
3. Press the icon, then the PROG icon.
4. When the hot water in the cup reaches the required level,
press the STOP icon.
The machine is now reprogrammed with the new quantity.
Please note!
• Tocancelprogramming,pressthe EXIT PROG icon.
Steam delivery
1. Check that the hot water spout is attached correctly.
2. Fill a container with the liquid to be heated or frothed and
immerse the steam spout in the liquid.
3 Press the icon (g. 37). After a few seconds, the steam
to heat the liquid comes out of the cappuccino maker;
4. When the required temperature is obtained, interrupt
steam delivery by pressing the STOP icon. (You should
not discharge steam for more than 3 minutes at a time).
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Tips for using steam to froth milk
• Whenchoosingthesizeofthecontainer,bearinmindthat
the liquid doubles or triples in volume.
• Foraricherdenserfroth,useskimmedorpartiallyskimmed
milk at refrigerator temperature (about 41°F/5°C).
• For a creamier froth, rotate the container with slow
movements in an upward direction.
• To avoid milk with poor froth or large bubbles, always
clean the spout as described in the following section.
Clean the steam/hot water spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and deliver
a little water by pressing the icon (g. 37). Stop
delivery of hot water by pressing the STOP icon again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout (g. 38) by
pressing the button. Hold the spout with one hand and
with the other, turn the cappuccino maker and pull it
downwards (g. 39).
3. Also remove the steam nozzle by pulling it downwards
(g. 40).
4. Check the hole in the nozzle shown by the arrow in g. 41
is not blocked. If necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
6. Insert the nozzle and cappuccino maker on the nozzle
by pushing it upwards and turning it clockwise until it is
attached.
MEMORISING YOUR PERSONAL PROFILE
With this appliance, you can memorise six
dierent proles, each associated with a
dierent color.
In each prole you can customise: