HFX85W15C AIR PURIFIER, HEATER AND FAN Instructions for use. Keep these instructions Visit www.delonghi.com for a list of service centers near you. ELECTRIC CHARACTERISTICS 120 V~ 60 Hz 1500 W PURIFICADOR DE AIRE, CALENTADOR Y VENTILADOR Repase y guarde estas instrucciones. Lea cuidadosamente este instructivo antes de usar su aparato. Visit www.delonghi.com para ver la lista de centros de servicios cercanos a usted.
EN ES page 4 page 13 2
C Q A L1 D M F B A L G M1 K H J I R E S 3 O P K1 G1 N F1 H1
IMPORTANT INSTRUCTIONS When using any electrical appliance, some basic safety pre- objects on or adjacent to the heater that may cause high temperatures. DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING. Important! Failure to observe the warning could result in injury or damage to the appliance. cautions should always be observed to reduce the risk of fire, electric shock, and/or injury to persons. Read all instructions carefully before using the appliance.
- - - - - - Connect to properly polarized outlets only. This heater is not intended for use with an extension cord or outlet strip. Plug the cord directly into an appropriate wall receptable. - Check that neither the appliance nor the power cable have been damaged in any way during transportation. - Do not use the appliance in rooms with a floor area of less than 43 square feet (4mq). - Make sure that no pieces of polystyrene or other packaging material have been left on the appliance.
DESCRIPTION A B C D E F F1 G G1 H H1 I J K K1 L L1 M M1 N O P Q R S - ON/STANDBY button Lid release button Air purification filter Remote control Control panel Heating button Heating mode Temperature buttons Temperature indicator (C° and F°) ECO button ECO function Airflow direction button Oscillation button Timer button Timer function Fan speed buttons Fan speed indicator Fan button Fan mode Hours Power indicator light Receiver for remote control Increase button Decrease button Handle Air inlet Air outle
- - desired temperature. symbol (F1); the temperature can be set by pressing the temperature buttons ( or ) (G) on the remote control. At first pressing, the display will show the current setpoint for approximately 4-5 seconds together along with the symbol; the temperature can be increased or decreased by pressing button or respectively. The minimum setting is 50°F (10°C) and the maximum is 82°F (28°C).
Please note: while this funtion is active, if the timer button is pressed one time, the remaining time will be shown on the display. Please note: if a power failure or power interruption occurs, the time function is reset and the appliance automatically goes to STANDBY. - Please note: if the ON/STANDBY button is pressed while the timer function is active, the unit changes its status (for example it goes to ON from STANDBY or vice versa) and timer function will be deactivated.
Changing the temperature scale To change the temperature scale, press the temperature button (G) and speed button (L) on the remote at the same time. An acoustic signal will sound and the display will show for 3 seconds "F" (Fahrenheit) or"C" (Celsius) with the symbol . Please note: when changing the settings, the oscillation temporarily stops for approximately 10-15 seconds before resuming.
Examples: brightness of the display: Please note: during the season when the appliance is in use, clean the air intake and outlet grilles regularly using a vacuum cleaner. Please note: never use abrasive powders or solvents to clean the appliance. Use only a soft damp cloth instead. Air purification filter maintenance It is good practice to clean the filter at regular intervals to remove accumulation of dust on the surface of the filter.
touch and hold the ON/STANDBY (A) button on the unit for at least 10 seconds until you hear a long beep. The filter is designed to last up to 9 months, based on 8 hours usage a day, at medium working load. Please note: the indicator is a guide and you may need to replace the filter more frequently, depending on the air quality conditions.
The display shows "cf" The filter has reached the pre-defined Replace the filter and reset the alarm. To reset the CF alarm, in rapid number of hours succession insert the plug and touch and hold the ON/STANDBY (A) button on the unit for at least 10 seconds until you hear a long beep. Check the appliance is correctly The display shows "Ht" or "It" blinking The internal temperature is too high.
57_00_1118 www.delonghi.
