Use and Care Manual

8
The most suitable temperature for the room during the summer
varies from 75°F to 81°F (24 to 27°C). You are recommended,
however, not to set a temperature much below the outdoor
temperature
DEHUMIDIFYING MODE
Ideal to reduce room humidity (spring and autumn, damp rooms,
rainy periods, etc). In dehumidifying mode, the appliance MUST
be set-up in the same way as for air conditioning, with the air
exhaust hose attached to enable the moisture to be discharged
outside. When the dehumidifying mode is selected, the light (P)
comes on and appears on the display.
At the same time, the AUTO fan light (N) comes on.
In this mode, fan speed is selected automatically by the appliance
and cannot be set manually.
FAN MODE
The unit operates without cooling or dehumidifying. This mode
provides ventilation only. When using the appliance in this
mode, the air exhaust hose does not need to be connected.
Adjust fan speed by pressing the “FAN” button (C) as described
for the air-conditioning mode. In this mode, AUTO speed cannot
be selected. The fan speed selected will be displayed.
SELF-DIAGNOSIS
The appliance has a self diagnosis system to identify a number
of malfunctions.
Error messages are displayed on the appliance display:
LOW TEMPERATURE
(frost prevention):
The appliance is tted with
a frost protection device to
avoid excessive formation of
ice on internal components.
The appliance starts up
again automatically when
the defrosting process is
completed.
PROBE FAILURE
(sensor damaged):
If this is displayed, contact
our toll free number.
FULL TANK:
Empty the internal tank, see
“End of season operations”.
SETTING THE TIMER
The timer can be used to delay appliance start up or shutdown.
This avoids wasting electricity by not operating the appliance
when it is not needed.
How to program delayed start up
• PlugtheapplianceintoanoutletandpresstheON/STAND-
BYbutton(A),thenselectthedesiredoperatingmodeand
other settings (temperature, fan speed, etc).
• Press the ON/STAND-BY button (A) again: The appliance
switches to stand-by mode (the two central segments are
displayed).
• PresstheTIMERbutton(D).Thelasttimersettingorthe
preset value 6.0 ashes on the display.
• Usethe+(E)or-(F)buttonstosetthenumberofhours
delay before the appliance comes on. During the rst ten
hours, you can select half hour intervals. For times greater
than ten hours, one hour intervals can be selected. If the
+ (E) or - (F) buttons are pressed for more than 2 seconds,
the time runs rapidly up to a maximum of 24 hours. Press
the timer button again within a few seconds to conrm
the setting. If the setting is not conrmed within a few
seconds, the display resets to Stand-by. With the timer
activated, the countdown before the programmed start
up time is displayed and the light (H) ashes. To cancel the
timer programming, press the timer button (D) again.
How to program delayed shutdown
• Delayedshutdowncan be programmedinanyoperating
mode (air conditioning/dehumidifying/fan).
• PresstheTIMERbutton(D).Thelasttimersettingorthe
preset value 6.0 ashes on the display.
• Usethe+(E)or-(F)buttontosetthenumberofhours
delay before the appliance goes o.
During the rst ten hours, you can select half hour intervals.
For times greater than ten hours, one hour intervals can be
selected. If the + (E) or - (F) buttons are pressed for more
than 2 seconds, the time runs rapidly up to a maximum
of 24 hours. Press the timer button again within a few
seconds to conrm the setting.
When the timer is set, the light (H) ashes.
At the set time, the air conditioner shuts down and remains
in stand-by.
To cancel the timer programming, press the timer button
(D) again.
MODELS WITH REMOTE CONTROL
• Point the remote control at the receiver on the air
conditioner. The remote control must be no more than 23
ft (7 metres) away from the appliance (without obstacles
between the remote control and the receiver)
• Theremotecontrolmustbehandledwithextremecare.Do
not drop it or expose it to direct sunlight or sources of heat.