LGHS 90II DGHS 90II COOKTOPS INSTALLATION and SERVICE INSTRUCTIONS USE and CARE INSTRUCTIONS distributed by DèLonghi Pty Ltd
Use and Care INSTALLATION CAUTION: < This appliance must be installed in accordance with these installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, AS5601 / AG 601 - Gas Installations and ony other relevant statutory regulations. < This appliance shall only be serviced by authorized personnel. WARNING: < This appliance is to be installed only by an authorised person.
Figure 1 DIMENSIONS (Table 2): (Note: Also refer to Figure 1) General Dimensions Width 860 mm Depth 500 mm Depth Below Mounting Surface 30 mm Cut-out Dimensions Width 840 mm Depth 480 mm 3
Use and Care INSTALLATION Installation clearances and protection of combustible surfaces shall comply with CLEARANCES: the requirements of AS5601 / AG 601 - Gas Installations.
The installation shall comply with the dimensions in Figures 1 and 2 bearing in mind that: < < < < A minimum distance of 20 mm has to be kept between the bottom of the cooking hob and the top of an appliance or a shelf. To ensure this clearance, mount the spacers, supplied with the appliance as shown in the figure below. A partition between the base of the hob and the cupboard below should be fitted 100 mm below the workbench surface if the cupboard is to be used for storage.
INSTALLATION (Refer to Figures 4a and 4b): < Spread out the gasket “C” over the workbench of the edge of the cut out taking care to overlap the gasket of the corners. < Slot in the cooking hob into the cut out of the workbench and locate it correctly. < Adjust the clamps “A” and tighten the screws “B” until the hob is firmly secured. < Using a sharp tool, trim any excess gasket which protrudes from the edge of the hob. < Assemble the three piece burners.
GAS SUPPLY: < This appliance is suitable for use with Natural Gas or LPG. (Check the “gas type” sticker attached to the appliance). < For Natural Gas the gas supply must be regulated to obtain a pressure of 1 kPa with the two semi-rapid burners operating at maximum. < For LPG models connect the gas supply directly to the appliance test point adaptor (supplied with the conversion kit) and ensure that the supply pressure is regulated to 2.75 kPa. < Do NOT force the “elbow” rotation prior to loosening the nut.
CONVERSION PROCEDURE INJECTOR REPLACEMENT: This appliance is suitable for use with Natural Gas or LPG. (Check the gas type” sticker attached to the appliance.) The nominal gas consumption and injector size details are provided in Table 1. The conversione procedure must be carried out only by an authorised person. To replace injectors: 1. Remove the knobs and ignition push button. 2. Unscrew the “A” screw in Figure 6a. 3. Remove the control panel “B” in Figure 6a. 4.
Figure 7a Figure 7b C C J J J J MINIMUM BURNER ADJUSTMENT: The minimum burner setting is adjusted as follows: 1. Turn on the burner. 2. Set the gas control to the minimum position. 3. Adjust the screw inside the gas cock shaft (see Figure 8a) to obtain a flame length of approximately 4 mm. OR Adjust the screw “A”on the side of the gas cock body (see Figure 8b) to obtain a flame length of approximately 4 mm. 4.
ELECTRICAL REQUIREMENTS: WARNING: 4 THIS APPLIANCE MUST BE EARTHED. CAUTION: 4 Ensure that the power outlet is properly earthed before connecting the appliance. 4 Disconnect power before servicing the appliance The appliance is provided with a standard 240VAC three pin plug and power cable (3x0.75 mm2).
Note: Servicing of this appliance is only to be carried out by Authorised Persons. REPLACEMENT OF IGNITION MODULE/ELECTRODES/GAS COCKS: 1. Turn off and disconnect gas supply and electricity. 2. Lift off trivets and burner heads, and pull off ignition push button and control knobs. 3. Undo the screws “B” and remove the clamps “A” shown in Figures 4a/4b and remove the hob. 4. Remove screws securing the top of the hob to the base pan and lift it off. 5.
Use and Care USE and CARE CAUTION: 4 This appliance must be used only for the task it has explicitly been 4 4 4 4 12 designed for, that is for cooking foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous. Do not use this appliance as a space heater. Do NOT place combustible materials or products on this appliance at any time. Do NOT spray aerosols in the vicinity of this appliance while it is in use.
Figure 10a Semi rapid burner no. 1 Semi rapid burner no. 2 mod. LGHS 90II Operates right rear burner Operates left rear burner Operates middle burner Operates left front burner Operates right front burner Ignition Wok burner Fish burner Simmer burner Figure 10b Semi rapid burner no. 1 Semi rapid burner no. 2 mod.
LIGHTING GAS BURNERS 4 Check that the electricity is switched on to allow spark ignition. 4 Make sure that all controls are turned to zero. 4 Model LGHS 90II: the gas flow to the burner is controlled by the knobs on the safety taps. 4 Model DGHS 90II: the gas flow to the burner is controlled by the knobs on 4 the taps incorporating a safety cut-off device. If the burner flame should go out, the safety cutoff valve will automatically stop the gas flow.
COOKING HINTS FOR GAS HOBS 4 The burners are different sizes, and can be used in different ways. 4 The largest can be used for boiling, to seal meat or foods that are cooked quickly, and the smallest for stews and sauces. 4 Always ensure that you use the correct size of saucepan. 4 For fast boiling, make sure the flame just reaches the edge of the pan. 4 Flames going up the side of the pan means wasted heat and the contents of the pan will take longer to boil.
CLEANING AND MAINTENANCE GENERAL ADVICE 4 It is advisable to clean when the appliance is cold and especially when cleaning the enamelled parts. 4 Avoid leaving alkaline or acid substances (lemon juice, vinegar, etc.) on the surfaces. 4 Avoid using cleaning products with a chlorine or acid base. ENAMELLED PARTS 4 All of the enamelled parts must be washed only with a sponge and soapy water or with non-abrasive products. Dry, preferably, with deer skin. STAINLESS STEEL 4 Clean with a suitable product.
Code 1101579 - Ed.4 - b6 Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right, considering the characteristics of the models described here, at any time and without notice, to make eventual necessary modifications for their construction or for commercial needs.
