User's Manual

VEHICLE DAMAGE WARNING
In this manual you will find the following Notices:
In the NOTICE area, you are informed of something that can damage your
vehicle. Many times this damage would not be covered by your warranty and
could be costly. The notice will tell you what to do to help avoid the damage.
NOTE: Other manuals may use NOTICE differently.
OPERATING INSTRUCTIONS
To learn how to get the most from your Delphi receiver, read all of the
instructions that follow.
Using the Clock
Your clock can function in a 12-hour or 24-hour mode. The 12-hour mode
distinguishes between AM and PM. The 24-hour mode operates as military
time.
Setting the Clock
1. Turn the ignition on.
2. Press and hold the “i Title/Menu” button for more than 2 seconds until the
menu appears. This indicates you are in the menu mode.
3. Press OK button to enter to the clock submenu.
4. Turn the ON/AUDIO knob or press the up/down buttons to change to SET
TIME. Press the OK button to enter set mode.
5. Turn the ON/AUDIO knob or press the up/down buttons to change between
12-hour or 24-hour format. Press the OK button to select one.
6. The display changes to clock configuration, causing the hour digits to flash.
Rotate the ON/AUDIO knob or press the up/down buttons to change the
hour. Rotating the knob clockwise or pressing the up button will increase
the hour; rotating counterclockwise or pressing the down button will
decrease the hour.
7. Press the OK button causing the minute digits to flash. Rotate the
ON/AUDIO knob or press the up/down buttons to change the minutes.
Rotating the knob clockwise or pressing the up button will increase the
minutes; rot
ating countercloc
kwise or pressing the do
wn but
ton will
decrease the minutes.
At any point in the time set process, not pressing a button or rotating the knob
within 8 seconds will cancel time set mode, ret
urn the radio to normal operation
and keep whatever setting changes have been made. Pressing the power or
NOTICE:
These mean there is something that could damage your vehicle.
463
::presione el botón durante menos de 2 segundos mientras se
reproduce un archivo MP3 para encontrar la carpeta anterior en el disco.
Saltar a inicio: presione el botón durante más de 2 segundos mientras se
reproduce un archivo MP3 para iniciar la reproducción en el primer archivo de la
primera carpeta.
: presione el botón durante menos de 2 segundos mientras se
reproduce un archivo MP3 para encontrar la siguiente carpeta del disco.
Saltar al final: presione el botón durante más de 2 segundos mientras se
reproduce un archivo MP3 para iniciar la reproducción en el primer archivo de la
última carpeta.
EJECT: presione el botón para expulsar un disco.
Para extraer un dispositivo USB, simplemente extraiga el dispositivo del puerto
USB. La radio regresará a su fuente/modo anterior.
Cómo utilizar un iPod
®
La radio puede controlar y reproducir música desde un iPod. Le recomendamos
que no conecte el iPhone 3G o iPod Touch a la radio.
Cómo reproducir un iPod
Introduzca el conector del cable USB del iPod en el conector USB de la radio (el
otro extremo conectado a su iPod). Se mostrará iPod READING en la pantalla.
Introduzca el conector de cable de audio de 3,5 mm al conector de entrada
auxiliar de la radio (el otro extremo conectado al conector de audio de 3,5 mm
de su iPod). Si el cable de audio no está conectado, la radio mostrará FRONT
AUX JACK UNPLUGGED. Después de que se hayan realizado todas las
conexiones y la radio haya terminado de leer el iPod, éste comenzará a
reproducir. Se mostrarán el tiempo transcurrido y el número de pista. La
reproducción comienza desde la pista actual reproducida en el iPod y continúa
en forma secuencial por todas las pistas desde el último modo seleccionado del
iPod. Después de reproducir la última pista, se detiene la reproducción y la radio
mostrará el menú del iPod.
Funciones de los botones
SEEK :
presione durante menos de 2 segundos para pasar a la siguiente
pista. Mantenga presionado el mismo botón para activar el avance rápido.
Cuando suelte el botón, la pista seguirá reproduciéndose.
SEEK : presione durante menos de 2 segundos para ir al comienzo de la
pist
a act
ual. Si se presionó dentro de los primeros 1
0 segundos de la pist
a,
pasará a la pista anterior. Vuelva a presionar el botón dentro del primer segundo
para ir al comienzo de la pista anterior. Mantenga presionado el mismo botón
para activ
ar el retroceso rápido. Cuando suelte el botón, la pista seguirá
reproduciéndose.