VENTILATION FAN / LED LIGHT MODEL 110LED-ADJ TABLE OF CONTENTS Package Contents 2 General Safety Information 3 Preparation and Wiring Diagrams 4 Assembly Instructions - New Construction 5 Assembly Instructions - Existing Construction 6 Grille Installation 10 Care and Maintenance 11 Troubleshooting 12 Dimensions 13 Product Specifications 13 Warranty 14 READ AND SAVE THESE INSTRUCTIONS Address: 46101 Fremont Boulevard, Fremont, CA 94538 US Toll Free Number: 1-888-979-9889 – Technical Su
PACKAGE CONTENTS 1 PART DESCRIPTION QTY 1 Fan Body 1 2 Grille 1 3 Suspension bracket Ⅰ 13”(318.5mm) 2 4 Suspension bracket Ⅱ 13”(318.
GENERAL SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS GENERAL SAFETY INFORMATION 7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit lnterrupter) – protected branch circuit. 1. Make sure that the electric service supply voltage is AC 120V, 60Hz. 8. Do not use this unit with any other solid-state control device.
PREPARATION Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Head Screwdriver, Utility Knife Helpful Tools (not included): Electric Drill, Drill Bits Proper insulation around the fan to minimize building heat loss and gain. 4” circular duct is recommended for installation. The ducting from this fan to the outside of building has a strong effect on air flow, noise and energy use of the fan.
ASSEMBLY INSTRUCTIONS NEW CONSTRUCTION – ATTACHING TO THE JOIST BEFORE INSTALLATION Turn off power source. Review all safety precautions. 1 1. Attach the duct connector from the housing can inside a , and secure using the duct screw (M4x12) b . Insert tab into slot in housing Hardware C Duct screw (M4X12) from Parts Bag b a Duct Screw 2 2. If spacing between joists is 12 in. apart, use four long wood screws (provided) to attach the fan body 1 to ceiling joists, NO NEED FOR SUSPENSION BRACKETS.
ASSEMBLY INSTRUCTIONS 4. Remove the fan junction box cover a . Using wire nuts (not supplied), connect house wires to fan wires b as shown in the wiring diagram on page 4. Reattach fan junction box cover c . 4 b c a 5 5. Connect a 4 in. circular duct a (not supplied) and vent to the outside. Secure it with duct tape (not supplied) or clamp (not supplied) to make the connection secure and air tight. Joist a Joist 6 6. Punch out Mask from packaging. Insert mask and finish celling.
ASSEMBLY INSTRUCTIONS 2. Measure the opening to ensure it is large enough to 2 accommodate the new fan body (10 1/4 in. x 10 1/4 in.). 3. If this fan is not replacing an old fan, be sure to cut a 10 1/4 in. x 10 1/4 in. opening for the fan body 1 . 2 3 /4" 10 1 10 " 1/4 4 Install from below, no need for suspension brackets (no attic access) 4. Remove fan unit by removing 3 screws. 5 5. A piece of wood (not supplied) is screwed in from below through the ceiling board. Suggested size is 1 in.
ASSEMBLY INSTRUCTIONS 6. Remove the fan junction box cover a . Using wire nuts (not supplied), connect house wires to fan wires b as shown in the wiring diagram on page 4. Reattach fan junction box cover c . 6 c a b 7 7. Insert housing can into the ceiling cut out. Secure the housing can from below by using 2 long wood screws through the flange into the wood support and 2 long wood screws through the flange into the joist. Hardware A Long wood screw 8 8.
ASSEMBLY INSTRUCTIONS Install from above with suspension brackets (attic accessible) *ONLY IF UNABLE TO ATTACH DIRECTLY TO JOIST(S) Turn off power source. Review all safety precautions. 1. For joist spacing 16 in. - 24in., insert suspension bracket I 3 and suspension bracket II 4 into the bracket cover on the duct connector side and the back of the fan body 1 . Install the suspension brackets to the joists with nails, and secure the suspension brackets to the fan body 1 by using the short screws (provided).
GRILLE INSTALLATION Insert the LED light connector into the fan body. Grille Slots Lighting Connector Attach grille 2 by pinching mounting springs a and insert into the narrow rectangular slots in fan body. CCT Switch Using the switch on the back of grille, choose the color temperature you want for your LED. You can choose from 2700K warm white, 4000K cool white, and 5000K daylight white.
CARE AND MAINTENANCE See safety information before proceeding. Routine maintenance should be done at least once a year. • Never use solvents, thinner or harsh chemicals when cleaning the fan. • Do not allow water to enter the motor. 1 • Do not immerse metal parts in water. • Do not immerse resin parts in water over 140º Fahrenheit. Turn off power source. Review all safety precautions. 1. To remove grille 2. Clean the grille 2 2 , squeeze springs and pull down. 2 2 in a sink and dry with a cloth.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should The fan is not clearing the room The light is not turning ON POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM too great 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2.
DIMENSIONS Unit: Inches (mm) PRODUCT SPECIFICATIONS Model No. 110LED-ADJ / VFB110D4LED3-A Voltage Frequency Air Flow @ 0.1"SP Power @ 0.1"SP Max Current Weight (V) (Hz) (CFM) (W) (Amps) (lb.) 120 60 110 14.8 Note: Design and specifications subject to change without notice. 13 0.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.
