VENTILATION FAN / LED LIGHT / LED NIGHT LIGHT MODELS SIG80-110 / SIG80-110D / SIG80-110H / SIG80-110MH / SIG80-110LED/ SIG80-110DLED / SIG80-110HLED / SIG80-110MHLED TABLE OF CONTENTS Package Contents 2 General Safety Information 3 Preparation 4 Wiring Diagrams 5 Assembly Instructions - New Construction 6 Assembly Instructions - Existing Construction 7 Grille Installation 11 Operation 12 Care and Maintenance 13 Troubleshooting 14 Dimensions 15 15 Warranty READ AND SAVE THESE INSTRUCT
PACKAGE CONTENTS 1 1 PART DESCRIPTION QTY 1 Fan Body 1 2 Suspension bracket 4 3 6" to 4" adapter 1 4 Grille 1 HARDWARE CONTENTS (Images are to scale) 2 2 X8 A Long Wood Screw ( 3 4 B 3 4 x 25mm) X4 Short screw (#8-32x1/4”) 44 SIG80-110 SIG80-110D SIG80-110H SIG80-110LED SIG80-110DLED SIG80-110HLED SIG80-110MH SIG80-110MHLED 2
GENERAL SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS GENERAL SAFETY INFORMATION 7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit lnterrupter) – protected branch circuit. 1. Make sure that the electric service supply voltage is AC 120V, 60Hz. 8. Do not use this unit with any other solid-state control device.
PREPARATION Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Head Screwdriver, Utility Knife Proper insulation around the fan to minimize building heat loss and gain. 6” circular duct is recommended for installation. The ducting from this fan to the outside of building has a strong effect on the Helpful Tools (not included): Electric Drill, Drill Bits WARNING: Turn off electricity at breaker box before beginning installation.
WIRING DIAGRAM Models: SIG80-110, SIG80-110MH JUNCTION BOX BLACK SWITCH BOX JUNCTION BOX OFF ON WHITE Models: SIG80-110HLED, SIG80-110DLED SWITCH BOX POWER SWITCH GREEN L RED N WHITE OFF ON GRD YELLOW LIGHT SWITCH OFF ON WHITE BLACK ON/OFF SWITCH (purchase separately) WHITE GROUND (bare) BLACK NIGHT-LIGHT SWITCH WHITE POWER SWITCH BLUE HI WHITE MODE SWITCH GREEN 120 VAC LINE IN N BLACK WHITE ON/OFF SWITCH (purchase separately) SWITCH BOX SWITCH BOX JUNCTION BOX RED OFF O
ASSEMBLY INSTRUCTIONS NEW CONSTRUCTION – ATTACHING TO THE JOIST BEFORE INSTALLATION Turn off power source. Review all safety precautions. 1 1. If spacing between joists is 12 in. apart, use four long wood screws (provided) to attach the fan body 1 to ceiling joists, NO NEED FOR SUSPENSION BRACKETS. Joist 1 Hardware A Long wood screw A 2 2. For joist spacing 16 in.- 24 in., insert suspension bracket 2 into the bracket cover on the duct connector side and the back of the fan . body 1 .
ASSEMBLY INSTRUCTIONS 3 3. Remove the fan junction box cover . Using wire nuts (not supplied), connect house wires to fan wires as shown in the wiring diagram on page 5 . 14AWG is the smallest conductor that shall be used for branch-circuit wiring. Reattach fan junction box cover . b c a 4. Connect a 6 in. circular duct (not supplied) and vent to the outside. Secure it with duct tape (not supplied) or clamp (not supplied) to make the connection secure and air tight. 4 a Joist Joist 5.
ASSEMBLY INSTRUCTIONS 2 2. Measure the opening to ensure it is large enough to accommodate the new fan body (10 1/4 in. x 10 1/4 in.). 3 3. If this fan is not replacing an old fan, be sure to cut a 10 1/4 in. x 10 1/4 in. opening for the fan body 1. 4"in. /.4 10 19 10 . n .4i" 19/4 Install from below, no need for suspension brackets (no attic access) 4 4. Remove fan unit by removing 3 screws. a A 3.5 in . 6 5 5. Remove duct connector by removing duct screw. Duct screw 1 6 6.
ASSEMBLY INSTRUCTIONS 7. Remove the fan junction box cover . Using wire nuts (not supplied), connect house wires to fan wires as shown in the wiring diagram on page 5. 14AWG is the smallest conductor that shall be used for branch-circuit wiring. Reattach fan junction box cover . 2 c a b 3 8. Insert housing can into the ceiling cut out. Secure the housing can from below by using 2 long wood joist. Hardware A Long wood screw 4 9.
ASSEMBLY INSTRUCTIONS Install from above with suspension brackets (attic accessible) *ONLY IF UNABLE TO ATTACH DIRECTLY TO JOIST(S) 1 1. For joist spacing 16 in.- 24 in., insert suspension bracket 2 into the bracket cover on the duct connector side and the back of the fan body 1 Install the suspension brackets to the joists with long wood screw, and secure the suspension brackets to the fan body 1 by using the short screws (provided).
Slots Celling Spring LED light connector GRILLE INSTALLATION Grille Model: SIG80-110MHLED Insert the LED light connector and the motion sensor connector into the fan body. Celling Spring LED light connector Motion sensor connector Grille Models: SIG80-110LED, SIG80-110DLED, SIG80-110HLED Insert the LED light connector into the fan body.
OPERATION LED indicator 80 110 80 70 80 50 60 90 SIG80-110MHLED Low speed air volume preset control (SIG80-110D, SIG80-110DLED, SIG80-110H, SIG80-110HLED, SIG80-110MH, SIG80-110MHLED) LOW SPEED CFM %RH 50 60 0 30 MOTION CONTROL FAN LIGHT FAN/LIGHT Motion / Humidity with LED light Model: Full speed air volume preset control • Motion control mode: Turn the POWER switch on to operate motion control mode.
CARE AND MAINTENANCE See safety information before proceeding. Routine maintenance should be done at least once a year. • Never use solvents, thinner or harsh chemicals when cleaning the fan. • Do not allow water to enter the motor. 1 • Do not immerse metal parts in water. • Do not immerse resin parts in water over 140º Fahrenheit. Turn off power source. Review all safety precautions. 1. To remove grille 4 , squeeze springs and pull down. 4 2. Clean the grille 4 2 in a sink and dry with a cloth.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM too great 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2. Check damper to ensure it is opening and closing properly.
DIMENSIONS Models: SIG80-110 / SIG80-110D Models: SIG80-110LED / SIG80-110DLED 12 23/64 (314.0) 7 7/8 (200) 13/16 (20.0) 13/16 (20.0) 12 3/8 (314.0) 9 21/32 (245.4) 11 21/32 (295.8) 6 (150) 12 23/64 (314.0) 11 21/32 (295.8) SIG80-110HLED / SIG80-110MHLED 6 (150) SIG80-110H / SIG80-110MH 7 7/8 (200) 12 3/8 (314.0) 9 21/32 (245.4) 3 3/4 (94.4) Unit: Inches(mm) 3 3/4 (94.4) PRODUCT SPECIFICATIONS SPECIFICATIONS Power @ 0.1”SP (W) Max. Current (amps) Weight (Hz) Air Flow @ 0.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.