User manual

INDEX
© 1999 DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
135
1
st
Step Speed Frequency, 59
AC Drive Operation Mode, 41, 42
AC Drive Operational, 41
Accel./Decel. Speed Inhibit, 49, 54
Acceleration S-Curve, 32
Acceleration Time 1 (Tacc1), 29
Acceleration Time 2 (Tacc2), 29
ACI/AVI Selection, 49, 58
ACI Input Loss Detection, 37
Analog Output Gain, 38
Analog Output Signal, 38
Auto Restart after Fault, 78
Auto-Acceleration/Deceleration, 32
Automatic Voltage Regulation (AVR), 78
Base-Block (B.B.) Indication, 41, 42
Base-Block Time for Speed Search, 76
Communication Protocol, 82
Content of User Defined Unit, 23
Continuous Output Time Limit, 70
Counter Reset, 49, 58
Counter Trigger, 49, 57
DC Braking Inhibit Frequency, 79
DC Braking Time during Start-up, 74
DC Braking Time during Stopping, 74
DC Braking Voltage Level, 74
Deceleration S-Curve, 32
Deceleration Time 1 (Tdec1), 29
Deceleration Time 2 (Tacc2), 29
Decrease Master Frequency, 49
Desired Frequency Attained, 39
Desired Frequency Attained, 41, 42
Dynamic Braking Voltage, 79
Electronic Thermal Characteristic, 70
Electronic Thermal Overload Relay Selection,
70
External Base-Block, 49, 55
External Fault, 49
Fault Indication, 41, 42
First-Second Accel./Decel. Time Selection,
49, 54
Identity Code of AC Motor Drive, 22
Increase Master Frequency, 49, 56
Jog Accel/Decel. Time Settings, 30
Jog Frequency, 31
Line Start Lockout, 58
Lower Bound of Output Frequency, 29
Low-Voltage Indication, 41, 42
Maximum Allowable Power Loss Time, 76
Maximum Output Frequency (FOmax), 26
Maximum Output Frequency Attained, 41, 42
Maximum Output Voltage (Vmax), 26
Maximum Speed Search Current Level, 76
Maximum Voltage Frequency (Fmax), 26
Mid-Point Frequency (Fmid), 27
Mid-Point Voltage (Vmid), 27
Minimum Output Frequency (Fmin), 27
Minimum Output Voltage (Vmin), 28
MODBUS Communication Watchdog Timer,
81
Momentary Power Loss Operation, 75
Motor No-Load Current, 72
Motor Rated Current, 72
Multi-Function Input Terminal, 48
Multi-Step Speed Command, 49
Over-Current Stall Prevention (during
acceleration), 68
Over-Current Stall Prevention (during
operation), 68
Over-Torque Detection Level, 70
Over-Torque Detection Mode, 69
Over-Torque Detection, 41, 42
Over-Voltage Stall Prevention, 67
Parameter Lock/Reset, 22
Password Input, 24
Password Configuration, 24
Pause PLC Program, 49, 57
PLC Forward/Reverse Motion, 64
PLC Mode, 59
PLC Program Completed, 41, 42
PLC Program Operation Paused, 41, 42
PLC Program Running, 41, 42
PLC Program Step Completed, 41, 42
Potentiometer Bias Frequency, 43
Potentiometer Bias Polarity, 43
Potentiometer Frequency Gain, 43
Potentiometer Reverse Motion Enable, 43
Preliminary Count Value Attained, 41, 42
Preliminary Count Value, 40
Present Fault Record, 71
PWM Carrier Frequency, 36
Rate Current Display of AC Drive, 22
Run PLC Program, 41, 42
Second Most Recent Fault Record, 71
Skip Frequency 1 Lower/Upper Bound, 78