DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 1 S-series Electronic Marshalling The DeltaV™ CHARM I/O Card (CIOC) with CHARMs I/O anywhere you need it Introduction Single channel granularity DeltaV™ S-series Electronic Marshalling delivers a new level of control system I/O performance with unprecedented flexibility and ease of use.
DeltaV Product Data Sheet October 2014 – Page 2 Benefits I/O anywhere you need it. DeltaV CHARM I/O Card (CIOC) provides an unprecedented flexibility in control system I/O topology. Using standard Ethernet infrastructure hardware you can add I/O anywhere you need it. From a local I/O cabinet to remote enclosures miles away, simply install the hardware and connect it to the DeltaV control network.
DeltaV Product Data Sheet October 2014 – Page 3 Product Description Electronic Marshalling hardware includes: CHARM I/O Carrier (DIN rail mounted and supports redundant pair of CHARM I/O Cards, redundant 24 VDC power connectivity, and redundant Ethernet communication modules) CHARM I/O Card (provides communication between CHARMs and the Ethernet I/O network to S-series controllers) CHARM Base plate (DIN rail mounted with interleaving power and bus connectors.
DeltaV Product Data Sheet October 2014 – Page 4 Label features are available to identify channel usage and Baseplate identification to help with maintenance. CHARMs can be added to any existing baseplate position and autosensed online. Additional CIOC’s can be added online. CHARM Types A variety of analog and discrete CHARMs are available to meet your specific requirements. The following CHARMs are available starting with v11.3.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 5 CHARM Keying Posts 28.8 VDC at 5 A switching current 48 VDC at 0.4 A switching current 250 VAC at 5 A switching current The Terminal Blocks contain keying posts that are automatically set and locked to the unique position of the installed CHARM. The keys prevent the insertion of an incorrect CHARM during maintenance activities. They are shipped in a neutral position and are set when a CHARM is inserted.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 6 CHARM I/O Card and Carrier Operating Temperature -40 to 70 °C (-40 to 158 °F) Operating Temperature -40 to 60 °C (-40 to 140 °F)
DeltaV Product Data Sheet October 2014 – Page 7 S-Series Electronic Marshalling CIOC Carrier Ethernet Communication Modules CHARM Baseplate with Identifier, CHARMs and Label Plates CHARM Baseplate Terminator, Top CHARM Baseplate Terminator, Bottom
DeltaV Product Data Sheet October 2014 – Page 8 S-Series Electronic Marshalling CHARM Baseplate Extender, Top CHARM Baseplate Extender, Bottom CHARMs
DeltaV Product Data Sheet October 2014 – Page 9 S-Series Electronic Marshalling DI 120 VAC Isolated Plus CHARMs CHARM Standard Terminal Block
DeltaV Product Data Sheet October 2014 – Page 10 S-Series Electronic Marshalling CHARM 3-wire DI Fused Injected Power Terminal Block CHARM Fused Injected Power Terminal Block CHARM Relay Output Terminal Block
DeltaV Product Data Sheet October 2014 – Page 11 S-Series Electronic Marshalling CHARM Thermocouple / mV Terminal Block Address Plug Address Plug Terminal Block
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 12 CHARM I/O Card hardware Specifications for CHARM I/O Card Carrier Number of I/O Cards per carrier 2 (redundant pair) Input power (redundant) +24 VDC ±10% at 12 A maximum Redundant Ethernet connections via replaceable IOP’s Fiber-optic: 100BASE-FX with MTRJ connectors; - Full duplex operation; - Multimode - 2 km nominal distance.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 13 CHARM Baseplate Number of channels per baseplate 12 Number of base plates per CIOC 8 Addressing One Address Plug (1 through 8) Terminal blocks - Shield connections 1 Screw Cage terminal per channel, plus 1 for cable shield 2 0.32 – 2.5 mm / 22 – 14 AWG Gold plated connectors for shield continuity Wire strip length 7 - 9 mm / 0.28 – 0.36 in.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 14 Specifications for Standard Terminal Block 2 Number of connections 4 Screw Cage terminals 0.32 – 2.5 mm / 22 – 14 AWG Strip length 7 - 9 mm / 0.28 – 0.36 in. Maximum Current 2 A max. at 250 VAC max. Color Black * Specifications for 3-wire DI Fused Injected Power Terminal Block 2 Number of connections 3 Screw Cage terminals 0.32 – 2.5 mm / 22 – 14 AWG Strip length 7 - 9 mm / 0.28 – 0.36 in.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 15 Analog Input 4-20 mA HART CHARM Specifications for AI 4-20 mA HART CHARM Sensor Types 4-20 mA with or without HART 0-20 mA Supports 2-wire and 4-wire device types directly Supports 3-wire device powered through the 24VDC Power CHARM Nominal signal range (span) 4-20 mA, (0-20 mA optional) Full signal range 0 to 24 mA Input Impedance 250 Ω ±1% Field Power (2-wire) 15.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 16 RTD Input CHARM Specifications for RTD Input CHARM Sensor types RTD input (Types listed in Table) Sensor Configuration 2 wire, 3 wire, or 4 wire Full Scale signal range See Table next page Accuracy See Table next page Repeatability 0.05% of span Resolution 24 bit A/D converter / Depends upon the sensor type Calibration None required Sensor excitation current 0.5 mA in 2-wire and 4 wire configurations 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 17 RTD, ohms Sensor Type Specifications Sensor Type Operating Range 25° Reference Accuracy Temperature Drift Pt100 -200 to 850°C ± 0.25° C ± 0.02° C/°C ~0.02° C Pt200 -200 to 850°C ± 0.25° C ± 0.02° C/°C ~0.02° C Pt500 -200 to 850°C ± 0.25° C ± 0.02° C/°C ~0.02° C Pt1000 -200 to 260°C ± 0.25° C ± 0.02° C/°C ~0.01° C Ni120 -80 to 260°C ± 0.15° C ± 0.01° C/°C ~0.01° C Ni100 -80 to 260°C ± 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 18 Thermocouple/mV Input CHARM Specifications for Thermocouple/mV Input CHARM Sensor types • Thermocouple • mV B, E, J, K, N, R, S, T, uncharacterized Low level voltage source (±20 mV, ±50 mV, and ±100 mV) Full Scale signal range See Table next page Accuracy See Table next page Repeatability 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 19 Sensor Type Specifications Sensor Type 1 25° Reference 1 Accuracy Temperature Drift Nominal Resolution Full Scale Operating Range B ± 0.8° C ± 0.06 ° C/ °C ~ 0.024° C 0 to 1820° C 250 to 1820° C E ± 0.4° C ± 0.03° C/ °C ~ 0.018° C -270 to 1000° C -200 to 1000° C J ± 0.6° C ± 0.04° C/ °C ~ 0.022° C -210 to 1200° C -210 to 1200° C K ± 0.4° C ± 0.03° C/ °C ~ 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 20 Analog Input 0-10 VDC Isolated CHARM Specifications for AI 0-10 VDC Isolated CHARM Sensor types Voltage device Full Scale signal range See Table below Accuracy See Table below Input Impedance 10 MΩ Repeatability 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 21 Analog Output 4-20 mA HART CHARM Specifications for AO 4-20 mA HART CHARM Sensor Types 4 to 20 mA with or without HART 0 to 20 mA Nominal signal range (span) 4 to 20 mA, (0 to 20 mA option) Full signal range 0 to 24 mA Accuracy over temperature range 0.25% of span (0 to 60 ºC) 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 22 Discrete Input NAMUR CHARM Specifications for DI NAMUR CHARM Sensor Types NAMUR Sensors, Dry Contacts, Dry contact with end of line resistance Detection level for On > 2.1 mA (<4 kΩ) Detection level for Off < 1.2 mA (>9 kΩ) Channel Impedance 1.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 23 Discrete Input 24 VDC low-side sense (dry contact) CHARM Specifications for DI 24 VDC low-side sense (dry contact) CHARM Sensor Types 24 VDC Dry Contacts Detection level for On > 2.25 mA (<5.3 kΩ) Detection level for Off < 1.75 mA (>8.2 kΩ) Channel Impedance 4.8 KΩ Wetting Voltage 22.5Volts (± 5%), current limited to 12.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 24 Discrete Input 24 VDC Isolated CHARM Specifications for DI 24 VDC Isolated CHARM Detection level for On > 10 VDC Detection level for Off < 5 VDC Wetting Current 6 mA @ 24 VDC Input Impedance 4 KΩ (approximately) Isolation Galvanically isolated and factory tested to 1000 VDC Configurable channel types: Dry contact or discrete state sensor changing <2 Hz Pulse train 0.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 25 Discrete Output 24 VDC High-Side CHARM Specifications for DO 24 VDC High-Side CHARM Device Type 24 VDC Solenoid coils On State Output rating 100 mA continuous @ 24 VDC Off-state leakage Current 1 mA maximum Line Fault Detection Configurable output behavior Line Fault Test timing Field Circuit Protection • Guaranteed short circuit: <50 Ω load • Guaranteed good status: 240 Ω to 10 kΩ load • Guaranteed open circui
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 26 Discrete Output 100mA Energy Limited CHARM Specifications for DO 100 mA Energy Limited CHARM Device Type 24 VDC Solenoid coils On State Output rating 100 mA continuous @ 24 VDC Off-state leakage Current 1 mA maximum Line Fault Detection Configurable output behavior Line Fault Test timing Field Circuit Protection • Guaranteed short circuit: <50 Ω load • Guaranteed good status: 240 Ω to 10 kΩ load • Guaranteed op
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 27 Discrete Output 24 VDC Isolated CHARM Specifications for DO 24 VDC Isolated CHARM Device Type 24 VDC Inductive Load Output range 4 VDC to 32 VDC Output rating 1.0 A continuous ( 2 A inrush for < 100 ms) Off state leakage Current 1 mA maximum Configurable output behavior • Momentary Output • Continuous Pulse Output Isolation The output channel is galvanically isolated and factory tested to 1000 VDC.
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 28 24 VDC Power CHARM Specifications for 24 VDC Power CHARM Device Type 24 VDC Power output Status read back level for power Good > 10 VDC Status read back level for power Bad < 5 VDC Isolation Status read back circuitry is optically isolated and factory tested to 1000 VDC. Output power has no isolation from the injection point.
DeltaV Product Data Sheet October 2014 – Page 29 S-Series Electronic Marshalling Simplified Circuit and Connection Diagrams for 24 VDC Power CHARM with Fused Injected Power Terminal Block – powering 3-wire HART Transmitter connected to AI HART CHARM 0/ 4 to 20 mA Simplified Circuit and Connection Diagrams for 24 VDC Power CHARM with Fused Injected Power Terminal Block powering 4-wire HART Transmitter connected to AI HART CHARM 0/ 4 to 20 mA
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 30 Discrete Input 120 VAC Isolated CHARM Specifications for DI 120 VAC Isolated CHARM Detection level for On > 84 VAC Detection level for Off < 34 VAC Wetting Current 2 mA at 120 VAC Input Impedance 60 KΩ (approximately) Maximum Input Voltage 130 VAC Frequency 50/60 Hz Isolation Each channel is optically isolated from the system at 250 VAC Configurable channel types: Dry contact or discrete state sensor changing
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 31 Discrete Input 120 VAC Isolated Plus CHARM Specifications for DI 120 VAC Isolated Plus CHARM Detection level for On > 84 VAC Detection level for Off < 34 VAC Wetting Current 10 mA at 120 VAC Input Impedance 12 KΩ (approximately) Maximum Input Voltage 130 VAC Frequency 50/60 Hz Isolation Each channel is optically isolated from the system at 250 VAC Configurable channel types: Discrete input Pulse Count Dry con
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 32 Discrete Input 230 VAC Isolated CHARM Specifications for DI 230 VAC Isolated CHARM Detection level for On > 168 VAC Detection level for Off < 68 VAC Wetting Current 1 mA at 230 VAC Input Impedance 240 KΩ (approximately) Maximum Input Voltage 250 VAC Frequency 50/60 Hz Isolation Each channel is optically isolated from the system at 250 VAC Configurable channel types: Dry contact or discrete state sensor changing
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 33 Discrete Output VAC Isolated CHARM Specifications for DO VAC Isolated CHARM Sensor types VAC Inductive load Output range 20 to 250 VAC Output rating 0.5 A continuous ( 10 A inrush for < 20 ms, 2.
DeltaV Product Data Sheet October 2014 – Page 34 System Compatibility CHARM I/O hardware requires: SD Plus controllers with DeltaV v11.3.1 or later software SX controllers with DeltaV v11.3.1 or later software SQ controllers with v11.3.1 or later software S-series Controllers with CHARMs I/O and M-series controllers can be installed on the same DeltaV Area Control Network in v11 and beyond.
DeltaV Product Data Sheet October 2014 – Page 35 S-Series Electronic Marshalling Certifications The following certifications are available for S-series Electronic Marshalling: CE: - EMC- EN 61326-3-1:2006 - LVD: Directive 2006/95/EC Aug 2007 FM: - FM 3600, Dec. 2011 FM 3611, Dec. 2004 FM 3810, Jan 2005 ANSI/ISA 60079-0, Oct 2009 ANSI/ISA 60079-15, Jul 2009 CSA: - CSA C22.2 No. 213-M1987, 1987 (Reaffirmed 2008) - CSA C22.2 No.
DeltaV Product Data Sheet October 2014 – Page 36 S-Series Electronic Marshalling Certifications S-series Electronic Marshalling will be submitted for the following certifications: EAC Hazardous Area certification Zone 2 (Russian, Belarus, Kazakhstan)
DeltaV Product Data Sheet October 2014 – Page 37 S-Series Electronic Marshalling Hazardous Area/Location: S-series Electronic Marshalling can be installed and used based on the following Standards: FM (USA): Installation and Field Circuits: Class I, Division 2, Groups A, B, C, D, T4 cFM (Canada): Installation and Field Circuits: Class I, Division 2, Groups A, B, C, D, T4 ATEX: Installation and Field Circuits: Ex nA IIC T4 Gc Ex nA [nL] IIC T4 Gc Ex nA [ic] IIC T4 Gc Ex nA nC IIC T4 Gc IEC-
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 38 Additional Field Circuit Certification Information CHARM Type Description Class I Division II Non Incendive Zone 2 Ex nL Certified Zone 2 Ex ic Certified Zone 2 Ex nA Certified DI NAMUR DI 24 VDC low-side sense (dry contact) DI 24 VDC Isolated ─ ─ ─ DO 24 VDC High-Side ─ ─ ─ DO 24 VDC 100mA Energy Limited DO 24 VDC Isolated ─ ─ ─ 24 VDC Power ─ ─ ─ AI 4-
DeltaV Product Data Sheet October 2014 – Page 39 S-Series Electronic Marshalling Ordering Information CHARM I/O Cards and Carrier Description Model Number Redundant CIOC with Copper Ethernet, includes redundant pair of CHARM I/O Cards, CHARM I/O Carrier with Screw Terminals, Copper I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall SE6501T01 Redundant CIOC with fiber optics Ethernet, includes redundant pair of CHARM I/O Cards, CHARM I/O Carrier with Screw Terminals, Fiber-Optic I/O Port
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 40 Ordering Information CHARM I/O Baseplate Extender and Terminator Description Model Number CHARMs Baseplate Extender with Cable Connectors, Top (Male) includes a Baseplate Identifier and a Baseplate Separation Wall SE4603T05 CHARMs Baseplate Extender with Cable Connectors, Bottom (Female) includes a Baseplate Identifier and a Baseplate Separation Wall SE4603T06 CHARMs Baseplate Terminator, Top (Male) includes a Baseplat
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 41 Ordering Information Low Voltage Instrumentation CHARMs Description Model Number DI NAMUR SE4301T01 DI 24 VDC low-side sense (dry contact) SE4301T02 DI 24 VDC Isolated SE4301T07 DO 24 VDC High-Side SE4302T01 DO 24 VDC Isolated SE4302T02 DO 24 VDC 100mA Energy Limited SE4302T04 24 VDC Power SE4302T05* AI 4-20 mA HART SE4303T01 Thermocouple/mV Input SE4303T02 RTD Input SE4303T03 AI 0-10 VDC Isolated SE43
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 42 Additional Ordering Information for Protection Cover and Terminal Blocks Protection Cover (fits all terminal blocks) Description Model Number CHARM Protection Cover; Package of 12 SE6103 Terminal Blocks Description Model Number Standard CHARM Terminal Block SE4501 3-wire DI Fused injected Power Terminal Block SE4512 Fused injected Power Terminal Block SE4502 Relay Output Terminal Block SE4503 Thermocouple/mV Te
DeltaV Product Data Sheet S-Series Electronic Marshalling October 2014 – Page 43 CHARM I/O Labeling and Spare part ordering Information CHARM I/O Labeling and Spare Parts Description Model Number Channel Identifier Labels for CHARM Baseplates; Package of 8 SE4606T02 Charm Baseplate Identifier; Package of 9 SE4606T03 Power Terminal Plug for CHARM I/O Carrier KJ4005X1-BF1 250V 2A Fuse for Fused Terminal Block; Box of 20 KJ4010X1-BC1 I/O Port Switch Module; Copper; for CIOC Carriers KL1601X1-BA1
