Installation Manual

ManualsBrandsDELTA FAUCET ManualsBathroom FixturesDelta Faucet Linden 2-Handle Centerset Bathroom Faucet with Diamond Seal Technology and Metal Drain Assembly, Champagne Bronze 2594-CZMPU-DST

90875 Rev. F

Para instalación fácil de su llave

Delta usted necesitará:

• LEER TODAS las instrucciones

completamente antes de empezar.

• LEER TODOS los avisos, cuidados,

e información de mantenimiento.

For easy installation of your

Delta faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and

maintenance information.

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

SILICONE

Icons

Pour installer votre robinet

Delta facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi que

toutes les instructions de nettoyage et

d’entretien;

90875

TWO HANDLE LAVATORY

CENTERSET FAUCETS

LLAVES DE DOS MANIJAS DE MONTURA

DE CENTRO PARA LAVAMANOS

ROBINETS À ENTRAXE COURT À

DEUX POIGNÉES

SILICONE

Icons

SILICONE

Icons

www.deltafaucet.com

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

Models/Modelos/Modèles

2538-DST, 2551-DST, 2552-DST,

2555-DST, 2564-DST, 2592-DST,

2593-DST & 2594-DST

10/24/2017 Rev. F

Summary of content (12 pages)

PAGE 1
TWO HANDLE LAVATORY CENTERSET FAUCETS LLAVES DE DOS MANIJAS DE MONTURA DE CENTRO PARA LAVAMANOS ROBINETS À ENTRAXE COURT À DEUX POIGNÉES 90875 Models/Modelos/Modèles 2538-DST, 2551-DST, 2552-DST, 2555-DST, 2564-DST, 2592-DST, 2593-DST & 2594-DST Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 2 A. A. 1 2 1 B. B. 1 2 2 1 1 A. Remove tube from end slot (1) and fully unwind tube. Repeat A. Slide gasket (1) up over tubes and mounting shanks. Install under B. Slide tube clip (1) from mounting shanks (2). Discard or recycle B. Align faucet so it is parallel to the sink edge, then, thread locknuts faucet body (2). Place tubes through mounting holes and slide faucet down until it rests on mounting surface. Note: If mounting surface is uneven, use silicone under the gasket.
PAGE 3
Standard Connections Conexiones Estándares Branchements Standard Custom Fit Connections Conexiones Especiales Branchements Spéciaux 2 3 1 1 2 2 3 4 4 3 1 1 2 4 Standard Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8".
PAGE 4
Custom Fit Connections - Plastic Sleeve Installation Instructions Conexiones Especiales - Instructions d’installations de le manchon en plastique Spéciaux Branchement - Instrucciones para la Instalación del la Manga Plástica Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2.
PAGE 5
B. C. E. D. 1 ON E 4 A. SI LI C 1 2 3 2 3 1 2 1 1 F. G. 4 2 2 H. 5 3 2 1 4 1 5 3 2 1 2 6 Step 3b Metal Pop-up A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. Step 3e Step 3c D. Apply silicone to underside of flange (1). G. Remove pivot nut (1). Install horizontal rod (2) and E. Pivot (1) must face faucet. Pull assembly H.
PAGE 6
NE I CO 1 SIL 4 C. B. A. 3 3 1 2 1 2 4 4 E. D. F. 3 2 2 4 5 1 3 2 1 4 5 3 1 6 Pop-Up with Metal Flange and Plastic Tail Piece emove stopper (1), brass nut & washer (2), black A. R gasket (3) and tail piece (4). pply silicone to underside of flange (1). Insert B. A flange into sink. C. Install black gasket (1), washer and brass nut (2) onto flange (3) from below sink, but do not tighten brass nut (2). Screw on tail piece (4) and hand tighten. D.
PAGE 7
5 1 3 3 2 2 4 4 Remove aerator (1) using supplied wrench (2) and turn faucet handles (3) to the full on mixed position. Turn on hot and cold water supplies (4) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Verify the seal is attached to aerator then reinstall. Note: For future use, aerator wrench (2) can be clipped to the supply line after flushing faucet. Check all connections at arrows for leaks.
PAGE 8
To Change the Position of Handle Stop (5). Para cambiar la posición de el tope (5). Pour changer la position de la butée (5). Cold Fría Froide Hot Caliente Chaude 8 5 5 5 6 4 7 5 3 4 9 La flecha va hacia el surtidor en lados calientes y fríos. 3 5 Arrow faces spout on both hot & cold sides. 3 1 Hot Caliente Chaude La flèche va vers le bec des côtés chauds et froids. Open/Abrir/Ouvert Cold Fría Froide Valves shown in closed position. Las válvulas en la posición cerrada.
PAGE 9
All Models 2538-DST 2551-DST H238p H251p RP41588p Lift Rod Barra de Alzar Tige de Manoeuvre RP60352 Bonnet Nuts Bonetes/Capuchones Chapeaux Filetés RP60400 Valve Assembly Ensamble de la Válvula Soupape RP54977 Aerator & Wrench Aereador y Llave Aérateur et Clé RP60400 Valve Assembly Ensamble de la Válvula Soupape RP51243 Gaskets (2) Empaques (2) Joints (2) RP72130p Decorative Supply Line Covers (metal) Quantity 2, 30” Long Available as Accessory Order (Not Included) RP52658p Set Screw and Button (
PAGE 10
2564-DST H264p RP25620p Set Screw (2) Tornillo de Ajuste (2) Vis de Calage (2) 2592-DST RP83791 Set Screw Covers (1 Red / 1 Blue /2 Gray / 2 Black) Tornillo Cubre (1 Rojo y 1 Azul / 2 Gris / 2 Negro) vis couvre (1 Red / 1 Blue / 2 Gray / 2 Noir) H292p RP25620p Set Screw (2) Tornillo de Ajuste (2) Vis de Calage (2) RP90913p Lift Rod & Finial Barra de Alzar y Pomo Tige de Manoeuvre et Grain de la Tirette RP78524p Button Covers Cubre botón Couvre-boutons RP90909p Lift Rod & Finial Barra de Alzar y Pom
PAGE 11
RP26533p Metal Pop-Up Assembly Less Lift Rod Ensamble de Metal del Desagüe Automático Sin la Barra de Alzar Renvoi Mécanique en Métal Sans la Tige de Manoeuvre RP23060p Flange Reborde Collerette RP6142 Gasket Empaque Joint RP6140 Nut & Washer Tuerca y Arandela/ Roldana Écrou et Rondelle RP50952 Plastic Sleeves Mangas Plásticas Manchons en plastique RP5648p Stopper Tapón Bonde RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM RP12516 Strap & Screw Barra Chata y Tornillo Feuillar
PAGE 12
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.