Installation Manual

ManualsBrandsDELTA FAUCET ManualsBathroom FixturesDelta Faucet Ashlyn 2-Handle Widespread Bathroom Faucet with Diamond Seal Technology and Metal Drain Assembly, Venetian Bronze 3564-RBMPU-DST

TWO HANDLE WIDESPREAD

LAVATORY FAUCETS WITH

EZ ANCHOR

INSTALLATION

EXTENSIÓN DE DOS MANIJAS

LLAVES DE LAVAMANOS CON

INSTALACIÓN DEL EZ ANCHOR

DEUX POIGNÉE RÉPANDUE

ROBINETS DE LAVABO AVEC

EZ ANCHOR

Model/Modelo/Modèle

3564-MPU-DST

Series/Series/Seria

ASHLYN

Para instalación fácil de su llave

Delta usted necesitará:

• LEER TODAS las instrucciones

completamente antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely before

beginning.

• To READ ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Icons

SILICONE

Icons

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi

que toutes les instructions de nettoyage

et d’entretien;

3/32" (2.38mm)

3/32 po

5/30/17 Rev. G

3/32" (2.38mm)

3/32 po

77310

www.deltafaucet.com

13/64” (5mm)

13/64 po

Summary of content (12 pages)

PAGE 1
TWO HANDLE WIDESPREAD LAVATORY FAUCETS WITH EZ ANCHOR® INSTALLATION 77310 EXTENSIÓN DE DOS MANIJAS LLAVES DE LAVAMANOS CON INSTALACIÓN DEL EZ ANCHOR® Model/Modelo/Modèle 3564-MPU-DST Series/Series/Seria ASHLYN® DEUX POIGNÉE RÉPANDUE ROBINETS DE LAVABO AVEC EZ ANCHOR® Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 A. B. C. Top View / Vista superior / Vue de dessus 1 1 2 2 2 1 2 1 1 3 2 A. Place black valve anchors (1) into the B. Place grey spout anchor (1) into the center C. IMPORTANT: Align valve anchors (1) A. Coloque los anclajes negros de la B. Coloque el anclaje gris del surtidor (1) en C. IMPORTANTE: Alinee las anclas de la B. Placez l’ancrage gris du bec (1) dans le C. IMPORTANT : Positionnez les ancrages outermost left and right sink holes.
PAGE 3
2 D. A. B. 1 5 3 2 1 1 2 2 Correct End Valve Orientation La Orientación de la Válvula Extrema Bonne configuration de la soupape 2 Top View of Anchors / Vista superior / Vue de dessus 1 1 1 1 1 1 Hot/Caliente/Chaude 2 Cold/Fría/Froide Open Abrir Ouvert Valves shown in closed position. Las válvulas en la posición cerrada. Soupapes montrées en position fermée. 4 D. Locate two screws (1) in the top of each A. The hot side valve assembly is labeled (1). Note: The hot B.
PAGE 4
3 C. A. 2 1 1 2 4 2 3 1 2 3 3 3 3 3 1 1 2 3 3 2 C. Place handle bases (1) over anchors and onto basin surface. Make A. Place spout base (1) over spout anchor and onto basin surface. Make C. Coloque las bases de la manija (1) sobre las anclas y en la superficie A. Coloque la base del surtidor (1) sobre el ancla del surtidor y sobre la C. Placez les bases de manette (1) sur les ancrages et sur la surface de A.
PAGE 5
B. Top View Vista superior Vue de dessus D. C. 5 3 2 1 6 4 Front Frente Avant Top View Vista superior Vue de dessus 2 6 1 4 Front Frente Avant 2 2 1 B. Feed spout tube (1) through indicated C. Spout tube (1) should be inserted completely D. Insert the large hex wrench (1) into lift rod B. Introduzca el tubo del surtidor (1) a través C. El tubo del surtidor (1) se debe insertar D. Inserte la llave hexagonal grande (1) en el B. Introduisez le tube du bec (1) dans le trou C.
PAGE 6
4 3 3 1 4 3 Line Línea Ligne 3 1 2 2 Insert spout tube (1) into outlet connector (2) to the first line, or until fully seated (about 3/4”). When properly inserted, you should not be able to see the line on the tube. Bend outlet tubes (3) and insert into outlet connector to the first line, or until fully seated (about 3/4”). When properly inserted, you should not be able to see the line on the tube.
PAGE 7
5 Standard Connections / Conexiones Estándares / Branchements Standard Custom Fit Connections / Conexiones Especiales / Branchements Spéciaux 2 1 2 3 2 3 1 4 Standard Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) to supply valve connection (4) and hand tighten, then tighten one additional revolution with wrench.
PAGE 8
Custom Fit Connections - Plastic Sleeve (Ferrule) Installation Instructions Conexiones Especiales - Instrucciones para la Instalación del la Manga Plástico (Casquillo) Branchements Spéciaux - Instructions d’installations de le manchon en plastique (Bague) Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Do not install plastic sleeve (ferrule) upside down. 1. Determine desired length of supply tube (1).
PAGE 9
6 A. D. C. B. 1 1 1 2 3 2 3 2 1 2 1 G. F. E. H. 4 2 3 1 1 5 2 4 2 5 3 2 1 1 6 Metal Pop-Up A. Remove stopper (1) and flange (2). D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place. DO NOT TWIST. C. Remove tailpiece (1) from body (2), add F.
PAGE 10
7 To Change the Position of Handle Stop (5). Para cambiar la posición de el tope (5). Pour changer la position de la butée (5). 3 1 2 3 Hot Caliente Chaude 5 5 Cold Fría Froide 5 4 3 La flecha va hacia el surtidor en lados calientes y fríos. Arrow faces spout on both hot & cold sides. 5 La flèche va vers le bec des côtés chauds et froids. Open Abrir Ouvert Valves shown in closed position. Las válvulas en la posición cerrada. Soupapes montrées en position fermée.
PAGE 11
RP72131p Decorative Supply Line Covers (PVC) Quantity 2, 30" Long Available as Accessory Order (Not Included) RP77421p RP77421-1.
PAGE 12
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.