DELTA HEAT GAS GRILL INSTALLATION, USE, & CARE MANUAL P/N: 17542A 10/18 MODELS: DHBQ26G-D DHBQ32G-D DHBQ32R/S-D DHBQ38G-D DHBQ38R/S-D
A Special Message to our Customers... Congratulations on your purchase of Delta Heat gas barbecue grill. Delta Heat is committed to making outdoor cooking products you’ll be proud to own for years. This manual gives you easy to follow instructions for installing, operating and maintaining your Delta Heat grill. We recommend reading this manual carefully before your first use to ensure safety, proper care and operation.
IMPORTANT SAFETY INSTRUCTIONS WARNING! Read this manual carefully and completely before using your grill to ensure proper operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or other injury. AVERTISSEMENT! Lire ce manuel avec soin et en entier avant l’utilisation de votre barbecue afin d’en assurer un fonctionnement, une installation et un entretien adéquats et réduire le risque d’incendie, de brûlures et d’autres blessures.
GENERAL SAFETY REQUIREMENTS • • • • • • • • • • • • The installation of this appliance must conform with local codes or, in the absence of local codes, either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1 or Propane Storage and Handling Code, B149.
TABLE OF CONTENTS GETTING STARTED GAS SAFETY REQUIREMENTS LP GAS HOOK-UP PORTABLE LP CONNECTION NATURAL GAS INSTALLATION LEAK TEST ELECTRICAL REQUIREMENT WIRING DIAGRAM BURNER FLAME / AIR SHUTTER ADJUSTMENT LOCATING THE GRILL GRILL CUT-OUT DIMENSIONS INSULATION JACKET ASSEMBLY INSTRUCTIONS OPERATING INSTRUCTIONS WINDY CONDITIONS CLEANING & MAINTENANCE TROUBLE SHOOTING GUIDE EXPLODED VIEW REPLACEMENT PARTS LIST WARRANTY HOW TO OBTAIN SERVICE 1-2 3 4 5 6 7 8 9 10 11 12 13 14-15 16-18 19 20-22 23 24 25-27 28
GETTING STARTED 1. Remove all packaging materials, labels and protective plastic film. DO NOT LEAVE UNIT UNDER THE SUN WITH PROTECTIVE PLASTIC FILM ON FOR A LONG PERIOD OF TIME AS IT WILL BECOME DIFFICULT TO REMOVE THE FILM. 2. Check to ensure that all grill accessories listed below are included.
GETTING STARTED - CONT. 5. Get familiar with the knobs and burners identification below: DHBQ26G-D DHBQ32G-D GRILL BURNER SEAR ZONE (OPT) GRILL BURNER ROTISSERIE Grill U-Burner (Standard) Located underneath the briquette trays 2 | www.deltaheat.com GRILL BURNER DHBQ38R/S-D DHBQ38G-D DHBQ32R/S-D GRILL BURNER / SEAR ZONE GRILL BURNER SEAR ZONE (OPT) GRILL BURNER GRILL BURNER / SEAR ZONE Sear Zone Burner (Standard on RS Models and Optional on R & G Models) Typically located on the left side.
GAS SAFETY REQUIREMENTS Each appliance is set and tested at the factory for the type of gas supply to be used. Identify the type of gas, either Natural Gas or LP gas and make sure that the marking on the data plate (rating plate) matches the gas being supplied to the grill. The data plate is located on the rear panel of the grill. A second label with model number and serial number is located under the right side of the control panel.
LP GAS HOOK-UP Install the factory-supplied hose and regulator assembly as shown. Connect the 3/8” flare end of the hose to the grill coupling using a ¾” open wrench. Do not apply pipe sealant to the 3/8” flare connection. Connect the regulator to the LP cylinder hand tighten it, do not use a wrench. Check for leaks using soapy water solution. (Reference page 8 for leak test procedure).
PORTABLE LP CONNECTION NOTE: USE ONLY A 20-LBS. (5-GALLON CAPACITY) GAS CYLINDER. WARNING: DO NOT PLACE MORE THAN ONE CYLINDER IN THE BASE CABINET ENCLOSURE AT ANY TIME. WARNING: DO NOT USE A DENTED OR RUSTED LP CYLINDER. NEVER USE A CYLINDER WITH A DAMAGED VALVE. ALWAYS CHECK FOR LEAKS AFTER CHANGING THE LP CYLINDER. (Page 7) THE LP PRESSURE REGULATOR AND HOSE SUPPLIED WITH THIS UNIT MUST BE USED WITHOUT ALTERATION. ALWAYS USE THE TANK SECURING DEVICE SUPPLIED WITH GRILL BASE. 1.
NATURAL GAS INSTALLATION The installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1 or Propane Storage and Handling Code, B149.2. 1. This gas appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at the test pressures in excess of 1/2 psi (3.5 kPa). 2.
LEAK TEST CAUTION BEFORE TESTING • Finding and/or fixing a gas leak is NOT a “DO-IT-YOURSELF” procedure. • NEVER USE THE GRILL WITHOUT FIRST LEAK TESTING THE GAS CONNECTIONS. • WARNING: DO NOT USE OPEN FLAME TO CHECK FOR LEAKS. USE OF AN OPEN FLAME COULD RESULT IN A FIRE, EXPLOSION, BODILY HARM OR DEATH. • DO NOT SMOKE WHILE PERFORMING THE LEAK TEST! • To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while performing a leak test. Perform leak test outdoors only.
ELECTRICAL REQUIREMENT TO INSTALL AND SECURE POWER TRANSFORMER Grill models with interior lights have a power transformer with an attached power supply cord. This transformer must be secured in a dry location and away from the grill firebox and excessive heat area. a. In a base cart application, four mounting screws with nuts are provided at the bottom left rear corner of the cart. If not provided, drill four holes using the transformer box as a template. Secure the transformer box as shown. (Fig. 1) b.
WIRING DIAGRAM DHBQ26G-D 12 VOLTS 120 VOLTS TRANSFORMER C - NO SPARK IGNITER 2 PIN PANEL PLUG + 12v HALOGEN LAMP NC LED LIGHT LED LIGHT 2 PIN PLUG FOR SIDE BURNER C C NO - - + MICRO SWITCH SPARK MODULE NC ILLUMINATION SWITCH NO + 9V MICRO SWITCH BATTERY PACK DHBQ32G-D DHBQ38G-D 12 VOLTS 120 VOLTS TRANSFORMER C - NO + 2 PIN PANEL PLUG SPARK IGNITER 12v HALOGEN LAMP 12v HALOGEN LAMP NC LED LIGHT LED LIGHT NO - + LED LIGHT 2 PIN PLUG FOR SIDE BURNER C C - SPARK IGNITER
BURNER FLAME / AIR SHUTTER ADJUSTMENT Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply may make it necessary to adjust the burners. The flames of the U-burners should be visually checked. Flames should be blue and stable with little to no yellow tips, no excessive noise or lifting. If any of these conditions exist, remove the burner and check to see if the air shutter or burner ports are blocked by dirt, debris, spider webs, etc.
LOCATING THE GRILL This gas appliance is designed and certified for outdoor use only. Do not locate this grill under unprotected overhead combustible surfaces. When installed under overhead combustible surfaces, a certified ventilating hood wider than the appliance shall be installed with a minimum distance of 36 inches above the cooking surface. NOTE: Caution should be taken when grills are used near glass, vinyl siding or other temperature sensitive construction materials.
GRILL CUT-OUT DIMENSIONS THESE DIMENSIONS ARE FOR NON-COMBUSTIBLE CONSTRUCTION ONLY. FOR COMBUSTIBLE CONSTRUCTION SEE NEXT PAGE. (SHOWN) DHBQ38R/S-D DHBQ38G-D DHBQ32G-D (SHOWN) DHBQ32R/S-D 38 32 DHBQ26G-D 19 3/4 26 36 1/2 9 1/2 19 3/4 30 1/2 9 1/2 19 3/4 24 1/2 9 1/2 * DETAIL NOTE: DETAIL IS TYPICAL TO ALL DHBQ CUT-OUTS. COUNTERTOP OVERHANG 12 | www.deltaheat.
INSULATION JACKET DHBQ32R/S-D 22.50 "A" 11 DHIJ32 APPLY WEATHER PROOF SEALANT "B" 21.50 10.50 INSULATING JACKETS MODEL “A” “B” DHIJ26 30.875 29 DHIJ32 36.875 35 DHIJ38 42.875 41 WARNING Do not build the grill under overhead combustible construction. If the grill is to be placed into combustible enclosure, an approved insulating jacket is necessary to prevent fire, property damage and bodily injury. Use only Delta Heat (DHIJ26, 32, 38) insulating jacket.
ASSEMBLY INSTRUCTIONS The DELTA HEAT Grill is produced fully assembled and tested in the factory and requires no major assembly in the field. For the purpose of safe shipping and transit, some parts such as the briquette trays and rotisserie components are wrapped inside the grill and require minor assembly. Check to ensure that all packaging material have been removed prior to grill operation. TO INSTALL BRIQUETTES TRAYS 1.
ASSEMBLY INSTRUCTIONS - CONT. ROTISSERIE ASSEMBLY For Larger Loads 1. Install the rotisserie motor horizontally as shown. The motor socket hole will line up with the front notch of the saddles. 2. Insert the rotisserie rod into the motor socket hole and place the rod on the front notch of each saddle. 3. Remove the stainless steel grates. 4. Place a basting pan on top of the briquette trays to catch the drippings. (Basting pan not supplied) For Smaller Loads 1.
OPERATING INSTRUCTIONS BEFORE LIGHTING THE GRILL • DO NOT ATTEMPT TO LIGHT THE GRILL IF YOU SMELL GAS. • WARNING! IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED WITH THEIR ORIFICES INSIDE THE BURNERS AIR SHUTTERS. If not properly installed, gas may leak outside of the burner that could lead to fire, potential damage to your grill, bodily injury or death. • Inspect the gas supply piping or hose prior to turning the gas ON.
OPERATING INSTRUCTIONS - CONT. Match/BBQ Lighter Lighting Instructions: If there is no electrical power supply available or if spark igniter will not light the burners, the burners can be lit manually using a lighted long match, taper or BBQ lighter. 1. Push and turn the knob counter-clock-wise to the biggest flame marking on the bezel. Hold the knob pushed in for 4 seconds. 2.
OPERATING INSTRUCTIONS - CONT. USING THE ROTISSERIE BURNER (For DHBQ32R-D & DHBQ38R-D Units) The Rotisserie system rotates the food in front of infrared burner heat for even cooking and juicier taste. 1. Install the rotisserie motor on the motor bracket and plug it in to proper voltage. Reference electrical requirements. (Page 8) 2. Insert the food on the middle of the spit rod and then secure it with the meat holders on both ends by tightening the thumb screws on the meat forks.
WINDY CONDITIONS High performance gas grills like Delta Heat produce intense heat. This is how they sear foods to lock in moisture and natural flavors. HOT AIR These high performance burners requires a constant steady supply of fresh air to mix with fuel. The grill is designed to pull air in through the front and vents hot gases out through the rear. Using grill in windy conditions may disrupt the front-toback air flow.
CLEANING & MAINTENANCE IMPORTANT STAINLESS STEEL & GENERAL PRODUCT CARE To keep your Delta Heat products free of surface corrosion and in good working order, it is important to take additional precautions under certain conditions. If your Delta Heat products are located in corrosive conditions, such as: • A coastal environment where corrosive salty air is present. • Near a swimming pool, hot tub or water feature with exposure to corrosive pool chemicals and/or chlorinated water.
CLEANING & MAINTENANCE - CONT. Do not use abrasives on the polished highlights. Be extra careful when cleaning around the highlights. Metal polisher or mild chrome cleaner can be used to bring back the luster on highlights. To touch-up minor scratches in the stainless steel, sand the affected surface very lightly, with 100-dry grit emery sandpaper in the direction of the grain.
CLEANING & MAINTENANCE - CONT. BURNERS Burners are made of heavy gauge stainless steel and can be soaked in water and cleaned with a wire brush. Check every port hole for clogs. Use a wire pin to clean out clogged ports. Make sure the burner is dry before installing it back into the grill. INFRARED SEAR ZONE BURNER The infrared burner has stainless housing and protective screen.
TROUBLESHOOTING GUIDE BEFORE CALLING FOR SERVICE: If your DELTA HEAT grill does not function properly, use the following troubleshooting guide before contacting your dealer for service. The troubleshooting guide may save the cost of a service call and the inconvenience of being without your grill. PROBLEM WHAT TO DO 1. Push in the knob and verify that the spark igniter functions. 2. If the igniter does not spark, replace 9V battery. a. Purge the line of any trapped air. Grill will not light. b.
24 | www.deltaheat.
REPLACEMENT PARTS LIST ITEM NO PART NO. DESCRIPTION DHBQ 26G-N DHBQ 26G-L DHBQ 32G-N DHBQ 32G-L DHBQ 32R/S-N DHBQ DHBQ 32R/S-L 38G-N DHBQ 38G-L DHBQ 38R/S-N DHBQ 38R/S-L 1 S13113 HANDLE BRACKET 2 2 2 2 2 2 2 2 2 2 2 S13134 HANDLE INSULATOR BRACKET 2 2 2 2 2 2 2 2 2 2 3 S14128 HOOD BUMPER 6 6 6 6 6 6 6 6 6 6 4 S12351 24.6” S/S TUBE HANDLE 1 1 - - - - - - - - 5 S12352 30.6” S/S TUBE HANDLE - - 1 1 1 1 - - - - 6 S12353 36.
REPLACEMENT PARTS LIST - CONT. ITEM NO PART NO. DHBQ 26G-N DHBQ 26G-L DHBQ 38G-L DHBQ 38R/S-N DHBQ 38R/S-L 52 S23338-26G 53 S23338-32G PANEL, FRONT, 26, G 1 1 PANEL, FRONT.
REPLACEMENT PARTS LIST - CONT. ITEM NO PART NO.
WARRANTY • LIMITED LIFETIME WARRANTY: Delta Heat warrants the stainless steel main burners, and fabricated stainless steel housing, to be free from defects in materials and workmanship under normal residential use for the lifetime of the product. This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust and oxidation which are normal conditions and are to be expected with any outdoor product.
HOW TO OBTAIN SERVICE For service, please contact your DELTA HEAT dealer or call DELTA HEAT direct at (562) 263-3600 or (800) 422-0091 or fax (562) 802-3391 Mailing address: DELTA HEAT, Inc. 13259 166th Street Cerritos, CA 90703 Visit us at www.deltaheat.
PLACE POSTAGE HERE Customer Service ATTN: Warranty Department 13259 166th Street Cerritos, CA 90703 Service Direct Line: (562) 263-3600 Fax: (562) 801-3391