Installation Guide

ManualsBrandsDelta ManualsCommercial ProductsDelta 1.5GPM Motion Activated Hardwire 1 Hole Electronic Bar / Prep Faucet with Control Box Thermostatic Mixing Valve and Antimicrobial By AgION from the Commercial Series

Page 1

208366 Rev. D

Write purchase model number here for future reference

PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc. as

items relating to ongoing maintenance suggestions and procedures are included.

*Package Quantities May Change.

Check the Parts section of the latest Delta Commercial Faucet Price List for current quantities.

OPTION LIST

TRANSFORMERS

060704A

Transformer 110 to 24 VAC 20VA

up to 5 Electronic Valves

060771A

Transformer 110 to 24 VAC 40VA

up to 10 Electronic Valves

060772A

Transformer 10 to 24 VAC 100VA

up to 25 Electronic Valves

Note: See page 3 for parts breakdown

on recessed mount boxes.

208366 208366 208366 208366 208366

NOTE: Control Box #0 and #1 are designed for routine 171°F (77°C)

disinfection cycles up to 30 minutes.

Control Box #8 is not recommended for high temperature disinfection

cycles as the thermostatic mixing valve limits the higher temperature

flow output.

NOTE: For optimum performance of this product, we recommend

a system pressure between 20 and 80 PSI static. This product

will operate up to a maximum of 125 PSI static per ANSI and CSA

requirements. However, we do not recommend pressure above

80 PSI. Thermal expansion or leaking pressure reducing valves

may require use of expansion tanks or relief valves to ensure

your system never exceeds its maximum intended pressure

setting.

061256A

36” Cable

Extension

RP30523

Braided Hose

060683A

24VAC to 6VDC

Converter

061001A

Gasket (6/pkg)

063160A

Thin Mount Kit

(3/8” Elbow, Nut,

Washer & Gasket)

063200A (R3)

063201A (R4)

063202A (R5)

063203A (R7)

063204A (R35)

Single-Hole Mount

Assembly including

Smooth-End Spout

with Flow Control,

Sensor & Gasket

(see correct RP # for

proper flow control

adaptor A & B,

ordered separately)

063163A

1.5 GPM

(5.7 L/min)

Bushing with Flow

Control

(to be used with

Control Box #’s

1,6 & 8)

063205A (R3)

063206A (R4)

063207A (R5)

063208A (R7)

063209A (R35)

Single-Hole Mount

Assembly including

Sensor, Gasket &

Spout with Aerator

Thread

063161A

Thick Mount Kit

(Nut, Washer, Gasket,

Shank, 1/4 NPT Pipe

& 3/8” Compression

Fitting)

061001A

Gasket (6/pkg)

063162A

1.5 GPM (5.7 L/min)

Adaptor with Flow Control

(to be used with Control Box #0)

#7 Smooth End

Spouts only

#7 Smooth End

Spouts only

060637A

1.5 GPM (5.7 L/min)

VR Laminar Outlet

with Antimicrobial

by Agion

060639A

1.5 GPM (5.7 L/min)

VR Flow Control

Aerator & Wrench

www .specselect.com

150__T4 __ __ __

063128A

Battery Box Assembly less driver

board and battery holder

Fig. 1

060681A

Battery Holder

060905A

Cover Gasket

060908A

Solenoid Holder

060906A

Surface

Mount Housing

061252A

Dual Driver Board

Masco H

Optics

& Proximity

063127A

Solenoid Valve with 3/8”

Compression Connectors

060909A

Screen Assembly

063131A

3/8” Comp Connect Nut

and Ferrile

063162A

1.5 GPM (5.7 L/min)

Adaptor with Flow Control

Summary of content (8 pages)

PAGE 1
50__T4 __ __ __ Write purchase model number here for future reference 208366 1.5 GPM (5.7 L/min) VR Laminar Outlet with Antimicrobial by Agion® 060639A 063161A 1.5 GPM (5.7 L/min) VR Flow Control Aerator & Wrench 208366 063200A (R3) 063201A (R4) 063202A (R5) 063203A (R7) 063204A (R35) Fig.
PAGE 2
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. INSTALLATION AND SET UP INSTRUCTIONS FOR SURFACE MOUNT HOUSING: CONTROL BOX #0 Fig. 2 STEP 1. FAUCET INSTALLATION Depending on the installation, use the 063160A thin wall kit OR 063161A thick wall kit (both provided as standard). Connect 20” braided hose to spout inlet. Clean surface where faucet will be mounted. Install faucet to sink/wall using nut and washer provided.
PAGE 3
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. INSTALLATION AND SET UP INSTRUCTIONS FOR RECESS MOUNT HOUSING: CONTROL BOXES #1 & 8 STEP 1. ROUGH IN Note: Wires connecting between box(es) and from transformer must be protected from abrasion, and being pulled at connections. They also may have to be fished through at a later stage of construction.
PAGE 4
INSTALLATION AND SET UP INSTRUCTIONS FOR RECESS MOUNT HOUSING: CONTROL BOXES #1 & 8 STEP 3. CONNECT WATER SUPPLY Fig. 8 Typical Installation (Recessed Mount Box) Gooseneck Spout Install sink and connect drainage to rough in. See applicable Fig. 6 or Fig. 7. Please note that the connection tube and fittings are supplied by the installer to connect the 3/8” MIP at the box outlet and compression joint for 3/8” O.D. Soft copper tube at the spout. Connect water supply through to spout.
PAGE 5
INSTALLATION AND SET UP INSTRUCTIONS FOR RECESS MOUNT HOUSING: CONTROL BOXES #1 & 8 STEP 7. TEST FOR OPERATION Operation Illustration Test for operation. If unit does not work properly, see Troubleshooting Guide on page 7. STEP 8. MAKING ADJUSTMENTS If adjustments are required. Note factory defaults for program shown in Quick Reference Chart. Otherwise, replace the driver board housing cover as the electronic product is ready for use.
PAGE 6
Function Function Setting To adjust settings, press and hold MODE (yellow pushbutton on left hand side) until the Function symbol appears. Once in Adjustment Mode, keep pressing MODE until desired Function is reached (see Quick Reference Table). To change Function Setting, press and release TOGGLE (white pushbutton on right hand side) until desired Function Setting is reached (see Quick Reference Table). Note: Will leave Adjustment Mode after 5 seconds.
PAGE 7
CARE INSTRUCTIONS This Delta Commercial faucet is designed and engineered in accordance with the highest quality and performance standards. With proper care, it will give years of trouble free service. Care should be given to the cleaning of this product. Although the chrome finish is extremely durable, it can be DAMAGED by ACIDIC CLEANERS (i.e. cleaners designed specifically for vitreous china lavatories and water closets), HARSH ABRASIVES or POLISH.
PAGE 8
Delta Commercial Faucet Limited Warranty All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book. This warranty is made to the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.