Installation Sheet

ManualsBrandsDelta ManualsCommercial ProductsDelta Commercial 1-1/2" Rear Spud Concealed Electronic Flush Valve with Field Adjustable 1.27 GPF to 6.6 GPF - Less Trim

210302 Rev. B

24VAC

6.4 VDC

160__T6__ __ __A

series

Write purchase model number here for future reference

Electronic

Concealed

Flushvalve

Nut

Fibre washer

Rubber washer

Slip Joint Nut Installation

Filter Screen

210302 210302 210302 210302

10a

10b

www.specselect.com

11a

11b

11c

PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc. as items

relating to ongoing maintenance suggestions and procedures are included.

For valves manufactured

after October 2014.

Summary of content (8 pages)

PAGE 1
Electronic Concealed Flushvalve Write purchase model number here for future reference 210302 210302 13 160__T6__ __ __A series 9 8a 7 210302 11b 11a 14 210302 24 8b 11c 25 10a Filter Screen 21 210302 12 24VAC 6.4 VDC 210302 10b 22 15 26 210302 210302 23 22 1 16 18 6 17 4 6 19 2 3 20 Slip Joint Nut Installation Nut 5 Fibre washer Rubber washer For valves manufactured after October 2014. 27 PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc.
PAGE 2
Item # 1 2 3 4 5 6 7 8a 8b 9 10a 10b 11a 11b 11c 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Description Universal TECK washers and O-rings repair kit Universal TECK parts washers and O-rings repair kit Transformer (110 to 24 VAC) for 5 sensor modules* Transformer (110 to 24 VAC) for 10 sensor modules* Transformer (110 to 24 VAC) for 25 sensor modules* Sensor module - urinal flush valve Sensor module - water closet flush valve Over-ride button assembly 4 pieces No.
PAGE 3
ELECTRONIC FLUSH VALVE INSTALLATION INSTRUCTIONS STEP 1 - ROUGH-IN FLUSH VALVE, FRAME OR BOX Fig. 1A Cable Bushing Knockouts NOTE: Due to excess back pressure of low flow water closets, outlet tubes must be braced to prevent tubes from disconnecting. Install and attach flush valve to water supply as per Fig.1C. Fig. 1B INSTALL FILTER SCREEN (included) : Small Sensor Box 6mm (1/4”) Min. 35mm (1-3/4”) Max. Note: Place filter in stop bore with conical screen facing the water flow.
PAGE 4
Fig. 1D BOF = Bottom Of Frame 305mm (12”) Square Frame 356mm (14”) Square Stainless Steel Cover 14” square stainless steel plate (frame 12” x 12”) 4-1/2” square stainless steel plate (box 4” x 4”) 14” x 20” stainless steel plate (frame 12” x 18”) frame outline Sensor Access Box Frame 76mm (3”) Minimum of Sensor** of sensor** Flushvalve of sensor** of sensor** 76mm (3”) to BOF 57mm (2.25”) to BOF 248mm (9.75”) to BOF Seat C L C L Bottom of rough in box to be 70mm (2.
PAGE 5
STEP 2 - INSTALL SENSOR PLATE If Hardwire Operated Fig. 2 Sensor Extension Cord Attach hardwire converter supplied to the 24VAC power source using the wire nuts provided. $WWDFK FRQYHUWHU WR WKH VHQVRU PRGXOH XVLQJ WKH VQDS FRQQHFWRU With power to flushometer, there will be a sequence of red lights that strobe across the sensing lens window which signifies that the valve is now in operation mode. ´ 3ODWH 0RGHOV Connect the female connectors from the sensor module to the solenoid flush valve.
PAGE 6
STEP 4 - MAKING ADJUSTMENTS (Optional: Only required if factory settings are not preferred.) 7R PRYH IURP RSHUDWLRQ PRGH LQWR VHW XS PRGH UHPRYH WKH SODVWLF SOXJ ORFDWHG LQ WKH UHDU RI WKH VHQVRU PRGXOH DQG SUHVV WKH set-up mode button once. A pencil or small screwdriver may be required. When done, place the plug back in the hole. 4.
PAGE 7
PROBLEM SOLVING & MAINTENANCE SUGGESTIONS NOTE: DO NOT USE EXCESSIVE FORCE to close the inlet stop stem. We RECOMMEND that the flushometer be flushed while closing the inlet stop. The noise created by the water flow or the flow into the fixture will stop when the inlet water is shut off. NOTE: Always use DELTA COMMERCIAL GENUINE PARTS to maintain the warranty. EXCESSIVE NOISE: 1. PARTIALLY close the inlet stop. 2.
PAGE 8
Delta Commercial Faucet Limited Warranty All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book. This warranty is made to the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.