Installation Guide

ManualsBrandsDelta ManualsKitchen Faucets16957-SPSD-DST

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

5/06/15 Rev. Awww.deltafauet.com

MEETS OR EXCEEDS — ASME A112.18.1 / CSA B125.1

ALCANZA O EXCEDE LAS SIGIENTES NORMAS —

ASME A112.18.1 / CSA B125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE

DEBE UTILIZAR CON MAQUINAS LAVAPLATOS PORTATILES! /

AVERTISSEMENT: ON NE DOIT PAS BRANCHER UN LAVE-VAISSELE

PORTATIF SUR CE ROBINET!

LE ROBINET EST CONFORME OU SUPÈRIEUR AUX EXIGENCES DES

NORMES SUIVANTES: ASME A112.18.1 / CSA B125.1

SINGLE HANDLE PULLOUT KITCHEN FAUCETS

LLAVES EXTRAÍBLES DE AGUA PARA COCINAS

ROBINETS À UNE MANETTE À BEC-DOUCHETTE

RÉTRACTABLE POUR ÉVIERS DE CUISINE

79947

1/8" (3.17mm)

Summary of content (9 pages)

PAGE 1
SINGLE HANDLE PULLOUT KITCHEN FAUCETS LLAVES EXTRAÍBLES DE AGUA PARA COCINAS ROBINETS À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE POUR ÉVIERS DE CUISINE Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 B. A. C. A. 1 2 1 B. 3 1 2 3 3 1 1 1 2 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. Place baseplate shanks (1) through mounting holes in deck. Option: If sink is uneven, use silicone sealant under the baseplate. CENTER MOUNT STYLE C. Secure faucet to sink with mounting nut and washer (1). Tighten securely by hand. Using a Phillips screwdriver, tighten locking screws (2). Install locknuts (3) and hand-tighten. A. Install round escutcheon (1) onto faucet (2).
PAGE 3
2 B. A. 2 OR 1 O 3 2 OU 3 4 2 1 1 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 4
3 1 2 3 2 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4). Tube should touch bottom of hole inside fitting. 4. Slide plastic sleeve down tube until it engages top of fitting.
PAGE 5
4 B. A. 2 3 1 1 2 3 4 2 1 2 1 3 1 3 2 3 1 Hose Installation A. Pass hose (1) through faucet (2). Thread wand assembly (3) onto hose (1) (unless already installed). Slide hose weight (4) over other end of hose. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Instalación de la Manguera A. Pase la manguera (1) a través de la llave de agua (2).
PAGE 6
5 Check all connections at arrows for leaks. Refer back to the appropriate installation instructions and retighten if necessary. If assembled correctly, check for damage to seals and order appropriate replacements. Examine los sitios con las flechas en las conexiones para asegura que no hay ninguna filtración de agua. Si es necesario, guíese por las instrucciones apropiadas para la instalación y apriete otra vez.
PAGE 7
6 7 2 6 3 4 1 5 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). Soap Dispenser Installation Remove nut (1). Separate head (2) from body (3).
PAGE 8
1/8" Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly.
PAGE 9
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.