Manual

240 VOLT OPERATION
Your drill press may be converted for 240 volt operation.
The conversion of your drill press for 240 volt operation
must be done by qualified electrical personnel. Should
you desire to have your drill press converted for 240 volt
operation, take your drill press to your local Authorized
Delta Service Center. You can call 800-223-7278 for the
location of the nearest Authorized Service Center.
When converted for 240 volt operation, your drill press is
intended for use on a circuit that has an outlet like the
one illustrated in Fig. 15. After conversion for 240 volts,
the drill press will have a grounding plug that looks like
the plug illustrated in Fig. 15.
Make sure the drill press is connected to an outlet
having the same configuration as the plug. No adapter is
available or should be used when the drill press is
converted for 240 volts. If the drill press must be
reconnected for use on a different type of electrical
circuit, the re-connection should be made by qualified
service personnel; and after re-connection, the tool
should comply with all local codes and ordinances.
GROUNDED OUTLET BOX
CURRENT CARRYING
_GROUNDING BLADE _-
IS LONGEST OF THE 3 BLADES
Fig. 15
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which
has a 3-prong grounding type plug and a 3-hole receptacle which will accept the tool's plug. When using an extension
cord, be sure to use one heavy enough to carry the current of the drill press. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. Fig. 16, shows the correct gauge to use depending on cord
length and voltage. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS
&mpere Volts Total Length of
Rating Cord in Feet
0-6 120 up to 25
0-6 120 25-50
0-6 120 50-100
0-6 120 100-150
6-10 120 up to 25
6-10 120 25-50
6-10 120 50-100
6-10 120 100-150
10-12 120 up to 25
10-12 120 25-50
10-12 120 50-100
10-12 120 100-150
12-16 120 up to 25
12-16 120 25-50
12-16 120
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS
Ampere Volts Total Length of
Rating Cord in Feet
0-6 240 up to 50
0-6 240 50-100
0-6 240 100-200
0-6 240 200-300
6-10 240 up to 50
6-10 240 50-100
6-10 240 100-200
6-10 240 200-300
10-12 240 up to 50
10-12 240 50-100
10-12 240 100-200
10-12 240 200-300
12-16 240 up to 50
12-16 240 50-100
12-16 240
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. 16