Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceClassic Single-Handle Bar Faucet in Venetian Bronze

SINGLE HANDLE CLASSIC

BAR / PREP FAUCET

GRIFO CLÁSICO MONOMANDO PARA

BARES / FREGADEROS DE PREP

ROBINET CLASSIC À UNE MANETTE

POUR ÉVIER DE BAR OU D’ÎLOT

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

•ToREAD ALLwarnings,care,and

maintenanceinformation.

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien;

Models/Modelos/Modéles

1903-DST

Series/Series/Seria

SILICONE

Icons

4/12/13   Rev.E

ASMEA112.18.1/CSAB125.1

Icons

61569

www.deltafaucet.com

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE CLASSIC BAR / PREP FAUCET GRIFO CLÁSICO MONOMANDO PARA BARES / FREGADEROS DE PREP ROBINET CLASSIC À UNE MANETTE POUR ÉVIER DE BAR OU D’ÎLOT 61569 ASME A112.18.1 / CSA B125.1 Models/Modelos/Modéles 1903-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 A. B. 2 A. 2 2 Front Frente Avant 3 1 2 3 1 1 2 4 3 1 1 Push valve to back of mounting hole. Empuje la válvula a la parte posterior del orificio de montaje. 4 5 Poussez la soupape vers l’arrière du trou de montage Valve Installation Spout Installation NOTE: These faucets are designed to fit a maximum countertop thickness of 2 1/2". A. SHUT OFF WATER SUPPLIES. Assemble spout (1) and gasket (2). Slide spout tube and shank (3) through mounting hole and position spout assembly on sink.
PAGE 3
B. C. 3 6 5 1 4 1 1 1 3 2 3 2 B. Slide tube end (1) into adapter (2) and secure with clip (3). Pull moderately on tube to ensure connection has been made. B. Deslice el extreme del tubo (1) en el adaptador (2) y fije con el gancho (3). Hale el tubo moderadamente para asegurar que la conexión se ha hecho. B. Introduisez extrémité du tube (1) dans l’adaptateur (2) et fixez-le avec l’agrafe (3).
PAGE 4
3 A. B. 2 2 1 OR 2 O 3 OU 3 4 1 1 2 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 5
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 6
4 1 2 3 Remove aerator (1) and move faucet handle (2) to the full on mixed position. Turn on hot and cold water supplies (3) and flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. Reinstall aerator. Check all connections at arrows for leaks. Re-tighten if necessary, but do not overtighten. Quite el aereador (1) y mueva la manija de la llave de agua (2) a la posición completamente abierta.
PAGE 7
5 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 8
1/8" (3.2 mm) 1/8 po (3.2 mm) 4 1 3 2 Maintenance If faucet exhibits very low flow: A. Remove aerator (1) and clean , or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (2). When reinstalling parts, make sure bonnet nut (3) is tightened securely with a wrench.* If faucet leaks from under handle: Remove handle and unthread trim sleeve (4). Using a wrench, ensure bonnet nut (3) is tight. If faucet leaks from spout outlet–SHUT OFF WATER SUPPLIES. Replace valve cartridge (2).
PAGE 9
RP152 Set Screw Tornillo de Presión Vis de Calage RP61981▲ Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP19754s Aerator Aereador Aérateur RP52833▲ Handle & Set Screw Manija y tornillo de presión Poignée et vis de calage RP61980▲ Sleeve Assembly Manja Manchon RP6052 Gasket Empaque Joint RP6052 Gasket Empaque Joint RP51503 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble de la válvula Soupape ▲ Specify Finish Especifíque el Acabado Précisez le Fini RP47029 Bracket Abrazadera
PAGE 10
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 11
Notes / Notas / Notes 11 61569 Rev.
PAGE 12
Notes / Notas / Notes 12 61569 Rev.