Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceIzak High-Flow Filtration Single-Handle Pull-Down Sprayer Kitchen Faucet in Stainless

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely before

beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Model/Modelo/Modèle

19939F-DST

Series/Series/Seria

6/5/14 Rev. A

ASME A112.18.1 / CSA B125.1

MEETS OR EXCEEDS — ASME A112.18.1 / CSA B125.1

ALCANZA O EXCEDE LAS SIGIENTES NORMAS —

ASME A112.18.1 / CSA B125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR

CON MAQUINAS LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF SUR CE ROBINET!

LE ROBINET EST CONFORME OU SUPÈRIEUR AUX EXIGENCES DES

NORMES SUIVANTES: ASME A112.18.1 / CSA B125.1

HIGH-RISE PULL-DOWN KITCHEN FAUCETS

LLAVES DE AGUA ELEVADAS, DESLIZABLES

HACIA ABAJO, PARA COCINAS

ROBINET À COL DE CYGNE ET BEC-DOUCHETTE

POUR DE CUISINE

1/8"

76420

Summary of content (21 pages)

PAGE 1
76420 ASME A112.18.1 / CSA B125.1 HIGH-RISE PULL-DOWN KITCHEN FAUCETS LLAVES DE AGUA ELEVADAS, DESLIZABLES HACIA ABAJO, PARA COCINAS ROBINET À COL DE CYGNE ET BEC-DOUCHETTE POUR DE CUISINE Model/Modelo/Modèle 19939F-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
SAFETY INFORMATION FOR FILTER Notice Read, understand, and follow all safety information contained in these instructions prior to installation and use. Retain these instructions for future reference. To reduce the risk associated with property damage due to water leakage or flooding: Intended use: Delta® system model professional water systems are intended for use in filtering drinking water in homes and has not been evaluated for other uses.
PAGE 3
INFORMACIÓN DE SEGURIDAD PARA EL FILTRO Aviso Lea, comprenda y siga toda la información de seguridad incluida en estas instrucciones antes de hacer la instalación y usar. Guarde estas instrucciones para referencia en el futuro. Para reducir el riesgo asociado con daños a la propiedad debido a fugas de agua o inundación: • Lea y siga las instrucciones antes de la instalación y el uso de este sistema; • Cumpla con todos los códigos de plomería estatales o locales.
PAGE 4
RENSEIGNEMENTS DE SÉCURITÉ CONCERNANT LE FILTRE Avis Lisez toutes les consignes de sécurité contenues dans les présentes instructions, assurez-vous de bien les comprendre et respectez-les lorsque vous installerez et utiliserez le filtre. Conservez ces instructions pour pouvoir les consulter ultérieurement. Pour réduire le risque de dommages matériels causés par une fuite d’eau : • Lisez les instructions avant d’installer et d’utiliser le système et respectez-les.
PAGE 5
Single Hole Installation / Instalación solo agujero / Un trou d’installation 1 C. A. 2 1 B. 4 5 6 3 A. Place gasket (1) into groove on bottom of faucet (2). C. Install mounting bracket (4) and nut (5) onto the mounting shank using wrench (6). B. Insert faucet tubes and mounting shank (3) through mounting hole. A. Coloque el empaque (1) en la ranura en la parte inferior de la llave de agua (grifo) (2). C.
PAGE 6
Three Hole Installation / Tres agujeros de instalación / Trois trous d’installation 1 A. D.-2 D.-1 B. 3 7 4 2 C. D.-3 3 6 8 1 8 5 2 Optional Escutcheon Installation Not included with all models - To order see replacement parts page for your model. C. Slide the tubes and shank of the hub (5) through the escutcheon and mount- A. For installations using the 10" escutcheon, be certain and use the 10" ing holes, then install hub onto escutcheon.
PAGE 7
2 A. C. B. 4 1 2 1 4 5 5 4 1 1 3 1 Hose Installation C. Slide spout assembly (4) onto hub (5). Use caution not to pinch A. Screw the threaded fitting of hose (1) into spray head (2) to prevent the fingers. Rotate spout assembly to ensure smooth operation. hose from being pulled into the spout until you are ready to flush the lines. Insert hose guide (3) into the other end of hose (1) as shown. B. Feed hose assembly (1) through spout (4) and hub (5). Instalación De la Manguera A.
PAGE 8
3 A. B. 2 1 2 1 1 3 2 2 1 2 3 1 Incorrect Installations. Hose Installation A. Remove hose guide and discard. Slide hose weight (1) over end of hose (2). Instalacións incorrecta. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Installations incorrecte. Instalación De la Manguera A. Quite y deseche la guía de la manguera. Deslice la pesa de la manguera (1) sobre el extremo de la manguera (2). B.
PAGE 9
4 Filter System Installation A. Parts and Materials Included: 1. Filter Cartridge 2. Filter Head Assembly 3. 3/8” x 24” PEX Adapter 4. #2 Phillips Mounting Screws Instalación del sistema de filtro Tools Required: 1. Drill (Cordless recommended) 2. Adjustable Wrench 3. Phillips head screwdriver A. Piezas y materiales incluidos: 1. Cartucho filtrante 2. Ensamblaje de la cabeza del filtro 3. Adaptador PEX de 3/8” x 24” 4. Tornillos de montaje #2 Phillips WARNING Herramientas necesarias: 1.
PAGE 10
Installation du système de filtration A. Pièces et matériaux inclus : 1. Cartouche filtrante 2. Tête de filtre 3. Adaptateur 3/8 po x 24 po en PEX 4. Vis de montage no 2 Phillips B. Outils requis : 1. Perceuse (perceuse sans fil recommandée) 2. Clé ajustable 3. Tournevis à embout Phillips (écart minimal par rapport à la base) 1 MISE EN GARDE Pour réduire le risque de suffocation : · Ne laissez pas un enfant de moins de 3 ans avoir accès à de petites pièces pendant l’installation du produit.
PAGE 11
C. D. 1 1 3 2 C. Check location of head/bracket (1): D. After checking location, Place filter head ■ Line up head with holes marked in step B. ■ Verify cold pex line (2) coming from faucet (blue end) can reach the outlet of the head unit. assembly holes over mounting screws and pull down to lock into place. Tighten the screws for a secure fit. ■ Verify the 24" PEX line (3) from cold water supply to head/bracket inlet is of appropriate length. The tubes can be looped if necessary.
PAGE 12
E. G. F. 9 10 6 7 5 11 8 E. Ensure the COLD water fitting (5), from the faucet, is free of debris. The cold water fitting (5) is 3/8” compression, with end colored blue. Secure metal nut on faucet tube to the filter outlet connection (6), marked with an arrow. Loop tubing if it is too long. Note: Recommended tubing minimum bend diameter is 8”. Hand tighten metal nut, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN.
PAGE 13
5 B. A. 1 2 OR 2 O 1 OU 3 2 1 4 A. HOT Water Line Connection Ensure all fitting and end connection is free of debris. Faucet fitting (1) is 3/8" compression, with end colored red for hot. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 14
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions (For Hot Water Line Only) 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 15
6 B. A. 3 A 4 2 A 1 B. Wand will lock into position when brought into proximity of the spout magnet. The A. Turn on hot and cold water supplies (1). Pull the hose assembly (2) out of the sprayer can be removed by either pulling directly out from the spout or by twisting 90° in either direction which will cause the magnets to repel and the head to decouple from the spout (recommended). spout and remove the sprayer (3).
PAGE 16
7 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 17
Mantenimiento del filtro de agua Cambie este filtro por lo menos cada seis meses. Condiciones locales del agua y el volumen real de agua pueden afectar la vida del filtro. Reemplace si ocurre una reducción apreciable de la presión en la llave de agua/el grifo. Instrucciones para el reemplazo del filtro 1. Coloque la bandeja debajo del filtro para colectar el agua residual que cae durante el cambio de cartucho. 2.
PAGE 18
3 4 5 6 1 7 2 Maintenance If faucet exhibits very low flow A. Remove and clean aerator (1) (Note: some models require wrench (2) to remove aerator.), or B. Unscrew hose from spray head and clean debris from screen - the screen is located just inside the spray (3). Note: Not all spray heads have a screen. IMPORTANT: Reinstall screen to the spray head. (Failure to reinstall the screen could damage internal parts.) If faucet leaks from under handle: Remove handle (4) and cap (5).
PAGE 19
RP47666 Set Screw Tornillo de Presión Vis de calage ▲ Specify Finish Especifíque el Acabado Précisez le fini RP73053▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP51502▲ Cap Casquete Embase RP62875 Friction Spacer Arandela de Fricción Rondelle de frottement RP78726 PEX Line PEX Línea PEX ligne RP47271▲ Set Screw & Button Tornillo de Presión y Botón Vis de calage et Bouton RP51503 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble d
PAGE 20
76420 Rev. A 2.0 mg/L ± 10% At least 10,000 particles/mL 2.0 mg/L 8,066,667 pts/mL 99.9% 34-8715-4621-3 Delta is a trademark of Delta. NSF is a trademark of NSF International. Replacement Filter: RP78702. For estimated cost of replacement elements: Visit www.deltafaucet.com or call 1-800-345-3358. Note: While the testing was performed under standard laboratory conditions, actual performance may vary.
PAGE 21
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.