(Model 23-589) PART NO. 901908 (013) Copyright © 2001 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, please call ESPAÑOL: PÁGINA 11 1-800-223-7278 (In Canada call 1-800-463-3582).
SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.
ADDITIONAL SAFETY RULES FOR GRINDERS 1. DO NOT OPERATE your tool until it is completely assembled and installed according to the instructions. 15. STAND to one side of the wheel when turning on the power. 2. IF YOU ARE NOT thoroughly familiar with the operation of grinders, obtain advice from your supervisor, instructor or other qualified person. 16. AVOID awkward hand positions where a sudden slip could cause a hand to move into the grinding wheel. 17.
UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the carton. Remove the protective coating from all unpainted parts. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline, or lacquer thinner for this purpose). WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL.
ASSEMBLY ASSEMBLING TOOL RESTS 1. Assemble the v-grooved tool rest (A) Fig. 3, to the inside of the right wheel guard using two 5/16-18x5/8" hex head screws (B), and 3/4" flat washers (C). C 2. Assemble the remaining flat surfaced tool rest (D) Fig. 4, to the inside of the left wheel guard in the same manner using two 5/16-18x1/2" hex head screws (E), and 3/4" flat washers (C). 3. Each tool rest is adjustable so that the edge (F) Fig.
2. Align the holes in the eye shield with the holes in the spark guard and place the eye shield bushing (A) Fig. 7, in between the space in the spark guard. A Fig. 7 D 3. Insert the eye shield bolt (A) Fig. 8, through the hole in the eye shield (B), eye shield bushing (C), and spark guard (D). C E F A 4. Place an 11/16" flat washer (E) Fig. 8, onto the end of the eye shield bolt and fasten the eye shield knob (F) to the end of the eye shield bolt. B 5.
1. All grounded, cord-connected tools: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. 2.
FLEXIBLE LAMP A The flexible lamp operates independently of the grinder. To turn the lamp on and off, rotate switch (A) Fig. 13. WARNING: To reduce the risk of fire, use 40 watt or less, 120 volt, reflector track type light bulb (not supplied). A standard household light bulb should not be used. The reflector track type light bulb should not extend below the lamp shade. Fig. 13 STARTING AND STOPPING GRINDER A The switch (A) Fig. 14, is located on the front of the grinder.
ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. WARNING: Since accessories, other than those offered by Delta, have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product.