Specification Sheet

Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.
Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.
Refer to www.specselect.com for individual models. Note: Use this page as a product submittal sheet.
DSP–3000T4128-HW Rev. B Page 4.C.1
Electronic Sensor Activated Wallmount
Faucet for Metered Mixed & Cold Water (HW)
Engineer/Architect Approval
Model Specified:
Approval: Date:
Approvals:
• CSA certified
• Complies to ASME A112.18.1/CSA B125.1
•
Indicates compliance to
ICC / ANSI A117.1
• EPA WaterSense listed
• Verified compliant with 0.25% weighted average
Pb content regulations
(Contact Delta Representative for State and/or Local Approvals.)
®
* Note: Not for use as an anti-ligature device.
Note: Measurements may vary ± 6mm (0.25")
ROUGH-IN Specification: (example)
• Rough-in parts only – requires separate order of 3000T4128ATR
trim to have complete product.
• Hardwire (24 VAC) infrared electronic handwash system.
• 254 mm (10") square metal box with cover – Hot and Cold inlet
supplies with stops, factory assembled with a point of use
thermostatic mixing valve with integral check valves to prevent
crossflow.
• 102 mm (4") square box with extension and plasterguard for
sensor wall plate.
• 102 mm (4") square box for spout wall plate.
• Outlet temperature range 35 - 48°C (95 - 118°F) on thermostatic
mixing valve.
• Maximum flow of 5.8 gpm (22 L/min) @ 45 PSI pressure loss,
minimum flow of 0.35 gpm (1.3 L/min) on thermostatic mixing
valve.
• Outlet flow reduced to a trickle in the event of a cold water
supply failure.
ROUGH-IN Models
❏
3000T4128ARI (Hardwire)
TRIM Specification: (example)
• Trim parts only – requires separate order of 3000T4128ARI to
have complete product.
• Hardwire (24 VAC) infrared electronic handwash system.
• 114 mm (4.5") square stainless steel wall plate with H
2
Optics
®
dual sensor for mixed or cold water.
• 114 mm (4.5") square stainless steel wall plate with chrome plated
rigid stub spout supplied with a 1.5 gpm (5.7 L/min) laminar
swivel outlet.
• 305 mm (12") square stainless steel wall plate for recessed
mounting of below deck 254 mm (10") metal box.
• Controller factory set to 203 mm (8") sensor range and a meter
mode of 10 seconds flow time – Field adjustable and retains
settings in event of a power failure.
TRIM Models
❏
3000T4128ATR (Hardwire)
❏3000T4128ATR-BB (Hardwire with 9V Battery Back-up)
Approvals:
• CSA certified to CSA B125.3, ASSE 1070 and NSF372
• Complies to NSF61 Section 9
• Verified compliant with 0.25% weighted average
Pb content regulations
(Contact Delta Representative for State and/or Local Approvals.)
257 mm
(10.13")
Control Box
305 mm (12")
Stainless Steel
Cover Plate
102 mm (4")
355 mm
(14")
max.
Product supplied as
shown by solid lines.
All items shown by
dotted lines supplied
by others.
Connection from 3/8"
MIP control box outlet
tube to 1/2" copper
on spout by others.
Rough-in box
to be installed
(flush to minus
6mm (1/4")) to
finished wall
Finished
Wall
Fasten box to
framing using
holes provided
inside of box
57 mm (2.25") Min.*
152 mm
(6")
Recommended***
19 mm
(3/4")
Max.
Sill Depth**
140 mm
(5.5")
Recommended***
Rough-In
0 to -1/4"
Slip on spout
tube (must be
braced, i.e.
copper
strapping)
Sink Deck
TYPICAL INSTALLATION
102 mm
(4")
102 mm
(4")
102 mm
(4")
114 mm
(4.5")
* A minimum 57 mm (2-1/4") installation height above fixture rim is
required unless a greater air gap is designated by local codes/regulations.
** A maximum sill depth of 19 mm (3/4") from backsplash to sink edge
is allowable.
DSP–3000T4128-HW Rev. B