Operating Guide

ManualsBrandsDelta ManualsBathTesla 8 in. Widespread 2-Handle Bathroom Faucet with Metal Drain Assembly in Stainless

07/01/2019 Rev. A

Failure to read these instructions prior to installation may result in personal

injury or property damage. Manufacturer assumes no responsibility for

product failure due to improper installation.

CAUTION

El no leer estas instrucciones de instalación puede resultar en lesiones

personales o daños a la propiedad. El fabricante no asume ninguna

responsabilidad por la falla del producto debido a una instalación incorrecta.

ADVERTENCIA

L’omission de lire les présentes instructions avant l’installation peut

entraîner des blessures ou des dommages matériels. Le fabricant se

dégage de toute responsabilité à l’égard d’un bris du produit causé par une

mauvaise installation.

CAUTION

Read all instructions prior to installation.

Veuillez lire toutes les instructions avant l’installation.

Lea todas las instrucciones antes de hacer la instalación.

1/8”

Image is for reference only.

La imagen es sólo para referencia.

L’image est fournie à titre indicatif seulement.

You may need:

Usted puede necesitar:

Articles dont vous pouvez avoir besoin :

1-800-345-DELTA (3358)

customerservice@deltafaucet.com

To reference replacement parts and access additional

technical documents and product info, visit

www.deltafaucet.com

Para referencia sobre las piezas de repuesto y acceder a

documentos técnicos adicionales e información del producto,

visite www.deltafaucet.com

Pour obtenir la référence des pièces de rechange ainsi

que pour avoir accès à d’autres documents techniques et

renseignements sur le produit, allez à www.deltafaucet.com

MODEL/MODELO/MODÈLE

TWO HANDLE WIDESPREAD

BATHROOM FAUCETS

LLAVES DE AGUA/GRIFOS

PARA BAÑOS DE DOS MANIJAS

SEPARADAS

ROBINET DE LAVABO À GRAND

ENTRAXE À DEUX MANETTES

106351

Regístrese en línea

S’enregistrer en ligne

www.deltafaucet.com/registerme

SILICONE

Icons

SILICONE

Icons

Summary of content (16 pages)

PAGE 1
06351 TWO HANDLE WIDESPREAD BATHROOM FAUCETS LLAVES DE AGUA/GRIFOS PARA BAÑOS DE DOS MANIJAS SEPARADAS MODEL/MODELO/MODÈLE ROBINET DE LAVABO À GRAND ENTRAXE À DEUX MANETTES Register Online Regístrese en línea S’enregistrer en ligne www.deltafaucet.com/registerme To reference replacement parts and access additional technical documents and product info, visit www.deltafaucet.
PAGE 2
Cleaning And Care Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Limpieza Y Cuidado De Su Llave Tenga cuidado al ir a limpiar este producto. Aunque su acabado es sumamente durable, puede ser afectado por agentes de limpieza o para pulir abrasivos.
PAGE 3
1 HANDLE INSTALLATION / INSTALACIONES DE MANIJAS / INSTALLATION DES MANETTES MODELS / MODELOS / MODÉLES 3556-MPU-DST & 3557-MPU-DST A. B. C. Correct End Valve Orientation La Orientación de la Válvula Extrema Bonne configuration de la soupape 2 Hot/Caliente/Chaude Cold/Fría/Froide 2 2 Open/Abrir/Ouvert Valves shown in closed position. Las válvulas en la posición cerrada. Soupapes montrées en position fermée. 1 3 4 D. E. 8 5 Hot Label Etiqueta Caliente Étiquette eau chaude 2 7 4 6 A.
PAGE 4
MODELS / MODELOS / MODÉLES 35718-DST, 35741-DST, 35776-MPU-DST & 357766-MPU-DST Slide end valves (2) gaskets (3) and bushings (4) into sink. Note: If sink is uneven, use silicone under the handle base (1). Bushings will not be required with holes smaller than 1 3/8" diameter, but should be used with holes larger than 1 3/8" diameter to properly center and seal the valves to the sink. Note: Valve with hot label should be installed in the left hole for proper handle rotation.
PAGE 5
2 SPOUT INSTALLATION / INSTALACIÓN DEL SURTIDOR / INSTALLATION DU BEC MODELS / MODELOS / MODÉLES 3538-MPU-DST, 3552-MPU-DST, 3555-MPU-DST, 3556-MPU-DST, 3557-MPU-DST, 3567-MPU-DST, 3568LF-MPU, 3593-MPU-DST, 3594-MPU-DST & 35955-DST Install the spout (1), gasket (2) and bushing (3). Bushings will not be required with holes smaller than 1 3/8” diameter, but should be used with holes larger than 1 3/8” diameter to properly center and seal the spout to the sink.
PAGE 6
CONNECTOR TUBE INSTALLATION / INSTALACIÓN DEL TUBO CONECTOR / RACCORDEMENT DES TUBES 3 MODELS / MODELOS / MODÉLES 3538-MPU-DST, 3552-MPU-DST, 3555-MPU-DST, 3556-MPU-DST, 3557-MPU-DST, 3559-MPU-DST, 3561-MPU-DST, 3593-MPU-DST, 3594-MPU, 35718-DST, 35741-DST, 35776-MPU-DST, 35955-DST & 357766-MPU-DST 3 Insert spout tube (1) into outlet connector (2) to the first line, or until fully seated (about 3/4"). When properly inserted, you should not be able to see the line on the tube.
PAGE 7
MODELS / MODELOS / MODÉLES 3567-MPU-DST & 3568LF-MPU Insert fitting (1) into Y-connector (2) until fully seated and secure with clip (3). Pull on hose to ensure it is firmly attached. Bend outlet tubes (4) and insert into outlet connector to the first line, or until fully seated (about 3/4”). When properly inserted, you should not be able to see the line on the tube.
PAGE 8
4 B. A. OR 2 O 1 1 3 2 3 OU 4 A. Standard Connections B. NOTICE NOTICE To avoid risk of property damage, Follow instructions for proper installation. Failure to follow these instructions may result in risk of property damage caused by leaking at this connection. Do not use pipe dope or other sealants on water line connections. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression. Loop tubing (2) if it is too long.
PAGE 9
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 NOTICE Failure to use plastic sleeve (ferrule) in the correct orientation will result in disconnection and possible water damage. 1. Determine desired length of supply tube (1). Leave 1" or 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (ferrule) (3) onto cut supply tube.
PAGE 10
5 A. B. E. D. C. 1 1 2 3 2 3 2 1 1 1 F. 2 2 H. G. 3 5 2 1 4 1 7 2 3 6 9 2 8 Metal Pop-Up A. R emove stopper (1) and flange (2). B. S crew nut (1) all the way down. Push washer (2) and gasket (3) down. C. R emove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. D. A pply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). 1 E. P ivot (1) must face faucet. Pull assembly (2) H.
PAGE 11
A. 6 B. 1 1 3 3 1 2 4 4 2 3 3 2 C. D. 5 4 3 4 5 4 5 2 2 3 1 4 Remove aerator (1) using supplied wrench (2) and turn faucet handles (3) to the full on mixed position. Turn on hot and cold water supplies (4) and flush water lines for one minute. 1 6 Important: This flushes away any debris that could cause damage to internal parts. 6 Verify the seal is attached to aerator then reinstall. Note: For future use, aerator wrench (2) can be clipped to the supply tube after flushing faucet.
PAGE 12
A. B. Correct End Valve Orientation La Orientación de la Válvula Extrema Bonne configuration de la soupape Hot/Caliente/Chaude Cold/Fría/Froide 5 3 6 1 8 4 2 Open/Abrir/Ouvert Valves shown in closed position. Las válvulas en la posición cerrada. Soupapes montrées en position fermée. 7 Maintenance B. SHUT OFF WATER SUPPLY VALVES. Replace valve assembly (7).* When reinstalling parts, make sure bonnet nut (8) is tightened securely with a socket. If faucet exhibits very low flow: A.
PAGE 13
Limited Warranty on Delta® Faucets In the United States and Mexico: Delta Faucet Company 55 E. 111th Street Indianapolis, IN 46280 Attention: Warranty Service www.deltafaucet.
PAGE 14
106351 Rev.
PAGE 15
106351 Rev.
PAGE 16
106351 Rev.