Installation Guide

ManualsBrandsDelta ManualsKitchenCassidy Single-Handle Pull-Out Sprayer Kitchen Faucet in Chrome

PULL-OUT KITCHEN FAUCET

LLAVE DE AGUA DESLIZABLE

PARA COCINAS

ROBINET À BEC-DOUCHETTE

POUR ÉVIER DE CUISINE

Models/Modelos/Modèles

4197-DST

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

6/17/13 Rev. D

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave

Delta

usted necesitará:

•LEER TODAS las instrucciones completamente

antes de empezar.

•LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your

Delta

faucet you will need:

•ToREAD ALL the instructions completely

before beginning.

•  To  READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet

Delta

facilement, vous devez:

•LIRE TOUTES les instructions avant de débuter;

•LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

CASSIDY™

73952

www.deltafaucet.com

ASME A112.18.1 / CSA B125.1

Summary of content (8 pages)

PAGE 1
PULL-OUT KITCHEN FAUCET LLAVE DE AGUA DESLIZABLE PARA COCINAS ROBINET À BEC-DOUCHETTE POUR ÉVIER DE CUISINE 73952 ASME A112.18.1 / CSA B125.1 Models/Modelos/Modèles 4197-DST Series/Series/Seria CASSIDY™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Cleaning and Care Backflow Protection System Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1.
PAGE 3
▲Specify Finish ▲Especifíque el Acabado ▲Précisez le Fini RP73941▲ Top Cap Remate superior Capuchon supérieur RP71543▲ Soap Dispenser (optional) Dispensador de jabón (opcional) Distributeur de savon (facultative) RP73940s Wand Assembly Ensamble de la Cabeza del Rociador Bec-douchette RP47888 Pump & Bottle Bomba y Botella Pompe et Bouteille RP73942 Retainer Funda Douille RP50815 Wrench Llave Clé RP60114 Cartridge Assembly Ensamble de la válvula Soupape RP71545▲ Optional 10 1/2" Escutcheon (mounts on
PAGE 4
1 B. A. OPTIONAL / OPCIONAL / FACULTATIVE 3 1 2 4 2 2 2 3 1 4 5 1 6 5 7 2 7 2 Optional Escutcheon Installation Mount Faucet to Deck A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/4" (35 mm +/- 6 mm) and a deck thickness of up to 3" (76 mm). Install gasket (1) into groove under base ring (2). Insert faucet tubes and shank through mounting hole in sink; and, place faucet over mounting hole. Note: With 10 1/2" escutcheon, maximum deck thickness is reduced to 2 3/4" (69.8 mm).
PAGE 5
2 A. B. 2 OR 2 1 O 2 OU 3 1 4 3 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
4 3 1 3 1 2 4 1 3 1 3 4 4 1 2 Flush Supply Lines Because your sprayer has been factory assembled to the hose, we do not recommend removing to flush the lines. Instead, if possible, we recommend placing a bucket below the outlet fitting and one of two options. 1. With the valve in mix open position (1), slowly open and close the supply stops (2). Clip Installation Insert hose end (1) through hose weight assembly (2). Push hose end (1) onto faucet outlet (3).
PAGE 8
5 1 3 1 2 4 7 6 5 Maintenance Check for Leaks Check all connections at arrows for leaks. Refer back to the appropriate installation instructions and retighten if necessary. If assembled correctly and still leaking, check for damage to seals and order appropriate replacements. The sprayer can be removed by pulling directly out from the spout. Check the operation of the sprayer by operating the trigger (1) from aerator to spray.