CORNER SHOWER BASE BASE PARA DUCHAS ESQUINA Models / Modelos Write purchased model number here. Retain these instructions for future use. Escriba aquí el número del modelo comprado. Conserve estas instrucciones para usarlas en el futuro. 422062 B711615-3838-WH B711917-3838-WH 100447 www.deltafaucet.com 1 06/25/2018 100447 Rev.
! REQUIREMENTS FOR SUCCESSFUL INSTALLATION KNOWLEDGE BASE: Framing Plumbing These instructions include suggestions for rough construction and plumbing installation. Local building codes vary and could supersede those suggestions. If you are not confident in your ability to perform these tasks, contract out those tasks you need help with or use a professional installer. DO NOT use drywall screws to secure flanges to wall studs. Product damage will occur and will void the warranty.
TOOLS AND MATERIALS REQUIRED • 2 x 4 lumber for additional wall studs • Rags or padding to protect product during bracing HERRAMIENTAS Y MATERIALES NECESARIOS • Madera para montantes de pared si instala el juego para pared adicionales; consulte las instrucciones de instalación del juego para pared • Conjunto de drenaje y desbordamiento que encajan en una bañera con una profundidad de 41,9 cm (16-1/2”) Drill Safety Glasses Caulk Gun Sealant (2 tubes) Adhesive Taladro Antiparras de seguridad Pistola
ROUGHING-IN • • • • Rough plumbing must be installed before base installation. Minimum stud pocket sizes are shown below. Drain cutout 5” diameter max. Right side plumbing rough-in shown. For masonry construction, floor and walls must be framed to accommodate plumbing and installation. IMPORTANT: IF INSTALLING MATCHING ENCLOSURE, refer to Enclosure Installation Manual for specific lumber sizes and placement. Additional studs will be required and need to be installed at this point.
2 1 Position base in corner. Check for level left to right and front to back. Mark unit position on floor and through drain opening. If the subfloor is not flat and level, use leveling compound or mortar bed to ensure that the base is level (shown in Step 5). Mark the locations of the studs on the flange of the base. These marks are used to verify base location after drain is installed in Step 4 and outline where adhesive is applied.
4 3 AVISO NOTICE NO corte el RIEL SUPERIOR del mismo largo que el RIEL INFERIOR. DO NOT cut the TOP TRACK the same length as the BOTTOM TRACK. 1 NOTICE For optimal water retention, water dam installation and/or proper caulking of this enclosure is necessary. Follow all steps as per sealant manufacturer’s instructions. AVISO Para una retención óptima del agua, la instalación de la lengüeta para la retención del agua y/o el calafateo de este recinto es necesario.
5 6 A 5” (12,7 cm) A. Flat and Level Floor Aplane y nivele el piso B. Uneven Floor Piso desnivelado 1 422062: 5/8” B711615-3838-WH: 1/2” B711917-3838-WH: 1/2” 2 A. If subfloor is flat and level, and mortar was not used, apply adhesive A on floor using 1/4" square-notched trowel, staying within pencil line (1). Proceed to step 7. Ensure that the waste pipe is properly located to align with the drain assembly (not included). Subfloor maximum diameter opening should be 5".
7 8 Shim 1 It is recommended not to stand in base while securing to wall. Set base in corner and press it into adhesive. Finish installing drain per manufacturer's instructions. 2 Secure flanges to all studs with 1 1/2” screws through previously drilled holes. 3 NOTE: Gaps between flanges and studs must be less than 1/8”. Insert shims to fill gaps if needed. Termine la instalación del desagüe de acuerdo con las instrucciones del fabricante.
CARE AND CLEANING 9 We recommend that you clean your acrylic bathing product with mild detergents. Use a terry cloth towel, soft cloth or sponge. Avoid using abrasive scrubbing pads, steel wool or sponges. After cleaning, rinse thoroughly with water. NOTICE When using drain cleaner or clog remover, rinse thoroughly with water. NOTICE Certain chemicals and cleaners may deteriorate the product surface, causing cracks and potentially, property damage.
NOTES / NOTA 10 100447 Rev.
NOTES / NOTA 11 100447 Rev.
Limited Warranty be made and replacement parts may be obtained by calling 1 800 355 2721 or by writing to: In the United States and Mexico: In Canada: Delta Faucet Company Masco Canada Limited, Plumbing Group Product Service Technical Service Centre 55 E. 111th Street 350 South Edgeware Road Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1 customerservice@deltafaucet.com customerservice@mascocanada.
