Installation Guide

ManualsBrandsDelta ManualsKitchenLinden Single-Handle Pull-Out Sprayer Kitchen Faucet with Multi-Flow in Arctic Stainless

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

s LEER TODAS las instrucciones completamente

antes de empezar.

s LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

s To READ ALL the instructions completely

before beginning.

s To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

sLIRE TOUTES les instructions avant de débuter;

sLIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Model/Modelo/Modèle

4353-DST

Series/Series/Seria

7/18/12 Rev. C

ASME A112.18.1 / CSA B125.1

MEETS OR EXCEEDS — ASME A112.18.1 / CSA B125.1

ALCANZA O EXCEDE LAS SIGIENTES NORMAS —

ASME A112.18.1 / CSA B125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR

CON MAQUINAS LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF SUR CE ROBINET!

LE ROBINET EST CONFORME OU SUPèRIEUR AUX EXIGENCES DES

NORMES SUIVANTES: ASME A112.18.1 / CSA B125.1

SINGLE HANDLE PULLOUT KITCHEN FAUCETS

LLAVES EXTRAÍBLES DE AGUA PARA COCINAS

ROBINETS À UNE MANETTE À BEC-DOUCHETTE

RÉTRACTABLE POUR ÉVIERS DE CUISINE

1/8"

SILICONE

60960

Summary of content (12 pages)

PAGE 1
60960 SINGLE HANDLE PULLOUT KITCHEN FAUCETS LLAVES EXTRAÍBLES DE AGUA PARA COCINAS ROBINETS À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE POUR ÉVIERS DE CUISINE ASME A112.18.1 / CSA B125.1 Model/Modelo/Modèle 4353-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly.
PAGE 3
1 B. A. C. A. 1 2 1 B. 3 2 1 3 1 3 2 1 1 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. 0LACE BASEPLATE SHANKS THROUGH MOUNTING HOLES IN DECK Option: )F SINK IS UNEVEN USE SILICONE SEALANT UNDER THE BASEPLATE CENTER MOUNT STYLE C. 3ECURE FAUCET TO SINK WITH MOUNTING NUT AND WASHER 4IGHTEN SECURELY BY HAND 5SING A 0HILLIPS SCREWDRIVER TIGHTEN LOCKING SCREWS )NSTALL LOCKNUTS AND HAND TIGHTEN A.
PAGE 4
2 B. A. 2 3 1 3 2 1 4 2 1 1 Hose Installation A. 0ASS HOSE THROUGH FAUCET 4HREAD WAND ASSEMBLY ONTO HOSE TO PREVENT IT FROM BECOMING LODGED IN FAUCET WHEN INSTALLING WEIGHT 3LIDE HOSE WEIGHT OVER OTHER END OF HOSE B. 0USH HOSE END ONTO FAUCET OUTLET !TTACH CLIP OVER HOSES AS SHOWN 0ULL DOWN MODERATELY TO ENSURE CONNECTION HAS BEEN MADE Instalación de la Manguera A.
PAGE 5
3 B. A. 2 OR 2 1 O 2 OU 3 1 3 4 1 2 4 Water Line Connections A. %NSURE ALL FITTINGS AND END CONNECTIONS ARE FREE OF DEBRIS &AUCET FITTINGS ARE COMPRESSION WITH ENDS COLORED RED FOR HOT AND BLUE FOR COLD ,OOP TUBING IF IT IS TOO LONG Note: Recommended tubing minimum bend diameter is 8". 3ECURE METAL NUT ON FAUCET TUBE TO SUPPLY VALVE CONNECTION AND HAND TIGHTEN THEN TIGHTEN ONE ADDITIONAL TURN WITH WRENCH DO NOT OVERTIGHTEN.
PAGE 6
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. )DENTIFY DESIRED LENGTH OF TUBE ,EAVE OF EXTRA LENGTH TO ALLOW FOR EASIER INSTALLATION AND CUT TUBE %NSURE CUT IS STRAIGHT AND BURR FREE 2. 3LIDE NUT AND PLASTIC SLEEVE ONTO CUT TUBE %NSURE SLEEVE IS ORIENTED AS SHOWN 3.
PAGE 7
4 5 2 A. B. 3 4 6 2 3 4 1 5 1 Soap Dispenser Installation 2EMOVE NUT 3EPARATE HEAD FROM BODY )NSERT BODY AND GASKET THROUGH SELECTED HOLE IN SINK -AKE SURE GASKET IS PROPERLY SEATED IN THE BASE 3ECURE BODY TO SINK WITH NUT &ROM UNDER THE SINK SCREW THE BOTTLE ONTO THE BODY ASSEMBLY SHANK )NSERT PUMP INTO HEAD THEN DROP INTO BODY NOTE: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle. $/ .
PAGE 8
6 1 2 Setting The Handle Limit Stop (Optional) 4HIS FAUCET INCLUDES AN INTEGRATED HANDLE LIMIT STOP THAT HAS TWO POSITIONS 0OSITION TO THE LEFT ALLOWS FULL HANDLE MOTION THE FULL RANGE BETWEEN hALL COLDv TO hALL HOTv 4HE FAUCET IS SET IN POSITION IN THE FACTORY 0OSITION TO THE RIGHT ALLOWS HALF OF THE NORMAL HANDLE MOTION hALL COLDv TO hMIXED HOT COLDv 4HE HANDLE LIMIT STOP CAN BE ADJUSTED BY THE HOMEOWNER ONCE THE FAUCET IS INSTALLED 3ETTING THE HANDLE LIMIT STOP IN POSITION MAY HELP TO
PAGE 9
1 2 3 1 Maintenance * WARNING: Failure to securely tighten bonnet nut with a wrench could result in water damage.
PAGE 10
RP40650 3ET 3CREW 4ORNILLO DE 0RESIN 6IS DE CALAGE RP60966S "UTTON "OTN "OUTON RP60965S ,EVER (ANDLE !SSEMBLY -ANIJAS DE 0ALANCA -ANETTE RP51502S #AP #ASQUILLO %MBASE RP51503 "ONNET 6 2ING "ONETE Y !RO 6 #HAPEAU ET *OINT Í LÞVRES RP50587 6ALVE !SSEMBLY %NSAMBLE DE LA VÕLVULA 3OUPAPE RP60964S (UB !SSEMBLY %NSAMBLE DE #UBO "O¦TER RP60963S 7AND !SSEMBLY %NSAMBLE DE LA #ABEZA DEL 2OCIADOR "EC DOUCHETTE RP63264 !DAPTERS v 5.%& TO v 5. !DAPTADORS v 5.%& A v 5.
PAGE 11
Notes / Notas / Notes
PAGE 12
Notes / Notas / Notes