50-868 PART NO. 410-09-651-0004 - 09-23-02 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, please call ESPAÑOL: PÁGINA 11 1-800-223-7278 (In Canada call 1-800-463-3582).
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.
13. DO NOT ATTEMPT TO REMOVE OR REPLACE THE FILTER(S) WHILE THE UNIT IS RUNNING. Make certain that the unit is disconnected from the power source. 14. MAINTAIN THE UNIT IN TOP CONDITION. Keep filters clean for optimum performance. Follow all instructions for changing and cleaning filters. 15. STORE THIS UNIT IN A LOCATION that eliminates the potential of damage to the power cord. Safely store power cord on the unit to eliminate tripping hazards. 16.
HOLES GROUNDED OUTLET BOX GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING MEANS ADAPTER GROUNDING BLADE IS LONGEST OF THE 3 BLADES HOLES Fig. A Fig. B EXTENSION CORDS MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS Ampere Rating 0-6 0-6 0-6 0-6 6-10 6-10 6-10 6-10 10-12 10-12 10-12 10-12 12-16 12-16 12-16 Use proper extension cords.
CARTON CONTENTS E B D A C Fig. 2 A - Air cleaner B - Four 1” eye-bolts C - Four 1/4-20 flange nuts D - Four rubber feet E - Remote Control Unit (Batteries not included) ASSEMBLY INSTRUCTIONS Determine whether the Air Cleaner will be used on the floor, on a bench, or hanging from an overhead support. If the Air Cleaner will be used as a mobile unit, proceed to “USING THE AIR CLEANER ON A BENCH OR FLOOR SURFACE” section.
USING THE AIR CLEANER ON A BENCH OR FLOOR SURFACE 1. Locate (4) self-adhesive rubber feet (A) Fig. 3, supplied with the unit. Carefully place Air Cleaner on a firm supporting surface with access to the bottom of the cabinet Apply a self-adhesive rubber foot (A) Fig. 3, to the bottom at each corner of the air cleaner cabinet. The rubber feet will help eliminate vibration and will prevent the possibility of the air cleaner “walking” across the work or floor surface.
D 1. Locate the four 1" eye bolts and the four 1/4-20 flange nuts supplied with the unit. C 2. Use a 5/32” Allen wrench (not supplied) to remove the four screws, (C) Fig. 5 from the top of air cleaner (D). 3. Thread one flange nut on the bolt approximately 3/4" of the threaded portion of the bolt. 4. Thread each eye-bolt into each of the four holes where screws were removed in STEP 2. Fig. 5 5. Fig. 6 illustrates the four eye bolts (F) attached to the top of the air cleaner.
USING THE REMOTE CONTROL B C G H F D To reduce the risk of fire or electric shock, do not use this unit with any solid-state speed control device. The remote control provided with this unit is not considered a solid-state device. A E The Air Cleaner is equipped with a REMOTE CONTROl (A) Fig.7A. NOTE: The remote requires two (2) AAA batteries (not supplied). Battery housing is located inside the back cover. I Fig. 7A Fig.
MAINTENANCE CHANGING AND CLEANING FILTERS 1. To remove the outer first stage filter (A) Fig. 8, lift and pull out the bottom of the filter as shown. 2. Remove inner bag filter (B) Fig. 9 in the same manner. 3. The first stage filter can be replaced or cleaned depending on its condition. Clean this filter in one of two ways: Use a shop vac to remove the dust, or use compressed air (30 psi maximum) to blow the dust out of the filter. Compressed air can be dangerous.
PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA Tempe 85282 (Phoenix) 2400 West Southern Avenue Suite 105 Phone: (602) 437-1200 Fax: (602) 437-2200 CALIFORNIA Ontario 91761 (Los Angeles) 3949A East Guasti Road Phone: (909) 390-5555 Fax: (909) 390-5554 San Leandro