Installation Guide

ManualsBrandsDelta ManualsBathDryden Single Hole Single-Handle Bathroom Faucet with Metal Drain Assembly in SpotShield Stainless

6/26/15 Rev. E

SILICONE

Icons

Model/Modelo/Modèle

551-DST & 751-DST

Series/Series/Seria

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

SILICONE

Icons

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Icons

SILICONE

Icons

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

SINGLE HANDLE LAVATORY

CENTERSET AND VESSEL FAUCETS

LLAVES MONOCONTROL DE MONTURA

DE CENTRO PARA LAVAMANOS

ROBINETS À ENTRAXE COURT À

UNE POIGNÉE

SILICONE

Icons

61836

1/8"

www.deltafaucet.com

Summary of content (12 pages)

PAGE 1
61836 SINGLE HANDLE LAVATORY CENTERSET AND VESSEL FAUCETS LLAVES MONOCONTROL DE MONTURA DE CENTRO PARA LAVAMANOS ROBINETS À ENTRAXE COURT À UNE POIGNÉE Model/Modelo/Modèle 551-DST & 751-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici. You may need/Usted puede necesitar/ Articles dont vous pouvez avoir besoin: LIC ON TEF LON SI E N O C LI SI • To READ ALL the instructions completely before beginning.
PAGE 2
LIFETIME FAUCET AND FINISH LIMITED WARRANTY All parts and finishes of the Delta® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for as long as the original consumer purchaser owns their home. Delta Faucet Company recommends using a professional plumber for all installation & repair.
PAGE 3
1 Model 551-DST / Modelo 551-DST / Modèle 551-DST A. A. 1 1 2 2 B. B. 4 4 3 3 5 5 For Three Hole Installation: For Single Hole Installation: A. Slide escutcheon (1) and spacer with round gasket (2) up over tubes and mounting stud. Position spacer and gasket under escutcheon. Slide tubes down through mounting hole and position faucet assembly on sink. Option: If surface is uneven, use silicone under the gasket. A.
PAGE 4
1 Model 751-DST / Modelo 751-DST / Modèle 751-DST A. B. 5 4 1 2 3 6 For Vessel Faucet Installation: A. Slide escutcheon (1) and spacer (2) with gasket (3) up over tubes and mounting stud. Position faucet assembly on sink. Option: If surface is uneven, use silicone under the gasket. B. Place metal bracket (4) over mounting stud (5) under sink. Secure with mounting nut / wrench (6). Para Instalaciones de Llaves de Agua en Artesas: B.
PAGE 5
2 A. B. OR 2 1 O 3 4 3 2 OU 2 1 1 2 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube. B.
PAGE 6
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
B. E. D. C. 1 SIL NE I CO 3 A. 1 2 3 2 3 2 1 1 1 F. G. 4 2 2 H. 5 4 3 2 1 5 4 1 2 3 2 1 6 Step 3b Metal Pop-Up A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). E. Pivot (1) must face faucet.
PAGE 8
4 3 1 2 2 4 4 Remove aerator (1) using supplied wrench (2) and move faucet handle (3) to the full on mixed position. Turn on hot and cold water supplies (4) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Reinstall aerator with wrench. Note: For future use, aerator wrench (2) can be clipped to the supply line after flushing faucet. Check all connections at arrows for leaks. Retighten if necessary, but do not overtighten.
PAGE 9
5 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 10
1/8" 5 4 3 1 2 Maintenance If faucet exhibits very low flow: A. Remove and clean aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (4) is tightened securely with a wrench.* If faucet leaks from under handle: Remove handle and pull off trim cap (5). Using a wrench, ensure bonnet nut (4) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3).
PAGE 11
Model / Modelo / Modèle 551-DST ▲Specify Finish Especifíque el Acabado Précisez le Fini RP61840▲ Escutcheon (3 Hole), Spacer and Gaskets Chapa de cubierta (3 agujeros), Separador y Empaques Plaque de finition (3 trous), Pièce d’espacement et Joints RP54976 Bonnet Bonete Chapeau RP47028 Gasket (1 Hole Only) Empaque (1 agujero Sólo) Joint (1 trou seulement) RP61837 Button / Botón / Bouton RP61838s Handle, Button & Set Screw Manija, Botón l y Tornillo de Ajuste Manette, Bouton et Vis de Calage RP50953 Se
PAGE 12
Model / Modelo / Modèle 751-DST RP61837 Button / Botón / Bouton RP50953 Set Screw Tornillo de Ajuste Vis de calage RP61838s Handle, Button & Set Screw Manija, Botón l y Tornillo de Ajuste Manette, Bouton et Vis de Calage RP54972▲ Cap Casquillo Embase RP54975 O-Ring Anillo O Joint torique ▲Specify Finish Especifíque el Acabado Précisez le Fini RP54976 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble de la válvula Soupape RP54977 RP54977-1.