Installation Guide

ManualsBrandsDelta ManualsBathTesla Single Hole Single-Handle Bathroom Faucet with Metal Drain Assembly in Polished Nickel

6/30/15 Rev. B

Models/Modelos/Modèles

552-LF-MPU, 552-LF-LPU & 752-LF

Series/Series/Seria

Tesla

™

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

SINGLE HANDLE LAVATORY

CENTERSET AND VESSEL FAUCETS

LLAVES MONOCONTROL DE MONTURA DE

CENTRO Y DE RECIPIENTE PARA LAVAMANOS

ROBINETS À UNE MANETTE POUR BASSIN

DE COMPTOIR ET

ENTRAXE COURT

1/16"

1/16 po

78509

www.deltafaucet.com

1/16"

1/16 po

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE LAVATORY CENTERSET AND VESSEL FAUCETS 78509 LLAVES MONOCONTROL DE MONTURA DE CENTRO Y DE RECIPIENTE PARA LAVAMANOS ROBINETS À UNE MANETTE POUR BASSIN DE COMPTOIR ET ENTRAXE COURT Models/Modelos/Modèles 552-LF-MPU, 552-LF-LPU & 752-LF Series/Series/Seria Tesla™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
1 1 For Three Hole Mount Para Las Instalaciones De Tres Agujeros Montage Sur Trois Trous A. For Single Hole Mount Para Las Instalaciones De Un Agujero Montage sur un trou A. 2 3 1 1 2 B. B. 4 5 3 4 5 6 For three hole mount: For single hole mount: A. Slide single hole gasket (1) up over tubes and mounting stud. Position faucet (2) and gasket on sink. Option: If sink is uneven, use silicone under the gasket. A. Slide escutcheon (1) and 3 hole gasket (2) up over tubes and mounting stud.
PAGE 4
2 A. B. OR 2 1 O 2 3 OU 4 3 2 1 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 5
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 6
3 4 1 2 2 3 1 3 3 Place a bucket below the outlet fitting and move the valve handle (1) to the open mixed position.Then, while holding the outlet tube (2) over the bucket, slowly open and close the supply stops (3). This will prevent debris from being lodged in the hose and aerator. Connect outlet tube (1) to spout tube (2) with supplied clip (3). Pull on hose (1) to ensure it is firmly attached.
PAGE 7
B. E. D. C. 1 SIL NE I CO 5 A. 1 2 3 2 3 2 1 1 1 F. G. 4 2 2 H. 5 4 3 2 1 5 1 2 3 2 1 6 Step 3b Metal Pop-Up A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place.
PAGE 8
6 RP26533▲ Metal Pop-Up Assembly Less Lift Rod Ensamble de Metal del Desagüe Automático Menos la Barra de Alzar Renvoi Mécanique en Métal Sans la Tige de Manoeuvre RP5648▲ Stopper Tapón Bonde RP12516 Strap & Screw Barra Chata y Tornillo Feuillard et Vis RP23060▲ Flange Reborde Collerette RP6142 Gasket Empaque Joint RP6140 Nut & Washer Tuerca y Arandela/ Roldana Écrou et Rondelle RP6132 Nut Tuerca Écrou RP12517 Horizontal Rod & Clip Barra Horizontal y Gancho Tige Horizontale et Agrafe RP6128 Tailpiece Tu
PAGE 9
Models / Modelos / Modèles 552-LF-MPU, 552-LF-LPU & 752-LF ▲Specify Finish Especifíque el Acabado Précisez le Fini RP78711s Bonnet & Glide Ring Capuchón y Aro para Deslizar Chapeaux et L’anneau de Glissement RP78712▲ Handle Manija Manette RP78713 Wrench Llave Clé RP78714 Bonnet Nut Tuerca del Bonete Chapeaux Fileté RP78709 Set Screw Tornillo de Ajuste Vis de Calage RP78715 Valve Assembly Ensamble de la válvula Soupape RP78710▲ Lift Rod & Finial Barra de Alzar y Pomo Tige de Manoeuvre et Grain de la Ti
PAGE 10
8 9 10 5 4 3 1/16" 1/16 po 7 6 1 2 Maintenance If faucet exhibits very low flow: A. Remove and clean aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (4) is tightened securely with a wrench.* If faucet leaks from under handle: Remove cover (6), set screw (7), bonnet (8) glide ring (9) and handle (10). Using provided wrench (5), ensure bonnet nut (4) is tight.
PAGE 11
Notes / Notas / Notes 11 78509 Rev.
PAGE 12
78509 Rev.