Specification Sheet

Page 4.C.81
L
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.
Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.
DSP–590-PHDF Rev. F
Electronic Proximity
®
Sensing
Technology Lavatory Faucets
Note: Measurements may vary ± 6mm (0.25")
Batteries included on all battery models. Flow Rates are at 60 PSI.
Note: Use this page as a product submittal sheet.
Refer to www.specselect.com for individual models.
SPECIFICATION: (example)
• Deck mount electronic lavatory faucet
• All metal spout construction
• Proximity
®
Sensing Technology
• Hardwire units supplied with 24 VAC to
6 VDC converter (Transformer required).
(Specify separately)
• Battery units supplied with 4 “AA” cell batteries
• Surface mount control box
• Mixing valve required (Order separately)
• Vandal resistant 0.5 gpm (1.9 L/min) laminar outlet
590-P Series
• Center mount, single hole installation
❏ 590-PLGHDF (Battery)
❏ 590-PLGHDFHW (Hardwire)
OPERATION:
• Hands free (touchless) operation.
• No visible sensor, the spout is the sensor.
• Water flows when sensing is activated.
• Water flow stops upon de-activation of sensing.
• Adjustable sensing distance factory set to
76 mm (3").
• Low battery audible beep (for battery models
only) will activate after faucet shuts off when
approximately 1500 cycles remain.
• Adjustable auto shut off feature. Factory set to
45 seconds.
• Metering mode with selectable flow times of
7 seconds to 4 minutes, factory set off.
• Periodic Rinse feature, time adjustable in 6 hour
increments up to 2 days. Selectable rinsing lengths
from 10 to 180 seconds. Factory set off.
NOTE 1: For optimum performance of this product, we recommend a
system pressure between 20 and 80 PSI static. This product will operate
up to a maximum of 125 PSI static per ANSI and CSA requirements.
However, we do not recommend pressures above 80 PSI. Thermal
expansion or leaking pressure reducing valves may require use of
expansion tanks or relief valves to ensure your system never exceeds
its maximum intended pressure setting.
NOTE 2: Designed for routine 180°F (82°C) disinfection cycles up to
10 minutes.
NOTE 3: Hardwire Proximity models not for use on enamel covered
metal sinks.
2.5
2
1.5
1
.5
0
0
0
1
2
3
4
5
6
7
8
9
10 20 30 40 50 60 70 80
Line Pressure (psig)
Outlet Flow Rates
FLOW
(L/min)
FLOW
(GPM)
FLOW RATE vs PRESSURE
3/8"
Compression
Connection
Outlet
Inlet 3/8" NPT or
3/8" Compression
Adaptor (Supplied)
36 mm
(1.43")
Battery Pack
1/8" Allen Screw
Recommended
381 mm
(15" max.) to
top of counter
146 mm
(5.73")
89 mm
(3.5")
MAX.
101 mm
(3.96")
139 mm
(5.47")
Battery Operated – Box shown.
Hardwire Version comes complete with Watertight
Connector and Hardwire Converter 24VAC to 6VDC.
Hardwire with Battery Backup
❏ Add suffix ”-BB” to Product Number.
Available on Hardwire models only.
See DSP-BB for detailed specification.
590-P SERIES ELECTRONIC DECK MOUNT LAVATORY FAUCET
VANDAL PROOF SURFACE MOUNT HOUSING
FRONT VIEW
590-P SERIES
TYPICAL INSTALLATION
SIDE VIEW
Approvals:
• CSA certified
• Complies to ASME A112.18.1/CSA B125.1
•
Indicates compliance to
ICC/ANSI A117.1
•
Verified compliant with 0.25% weighted average Pb
content regulations
( Contact Delta Representative for State and/or
Local Approvals.)
Patented
®
82 mm
(3.2")
135 mm
(5.3")
109 mm
(4.3")
56 mm
(2.2")
156 mm
(6.1")
64 mm
(2.5")
Max
Deck
Thickness
3/8"
Compression
Connection
330
mm
(13.0")
MAX.
178 mm
(7.0")
MAX.
Sensor
Wire
508 mm
(20.0") Dia.
Braided
Polymer Hose
3/8"
Compression
Connection
56 mm
(2.22")
32 mm
(1.25") Dia.
Hole
Required
3/8"
Compression
Connection
Available Option for
Field Conversion
❏ 060651A
3 Position Switch
See DSP-ELACC for
detailed specification.