Specification Sheet

Electronic Faucets
4" Cast Deck mount electronic Proximity® Sensing
Technology lavatory faucet - hi-rise spout
Model No: 591TP0238TR
SPECIFICATION:
•
Proximity® Sensing Technology
•
Chrome plated CAST 102 mm (4") spout body
•
Adjustable sensing range and timeout
•
Mixing valve required (order separately)
•
Serviceable filter screen upstream of the solenoid valve
•
Metal hold-down package
•
Supplied as complete product
•
Outlet#: 3 - Vandal Resistant 1.5 gpm (5.7L/min) Flow Control Aerator
•
Supplied as trim parts only – requires separate order of ELAVT0008ARI
rough-in to have complete product
•
(24 VAC) Hardwire powered by Class II transformer (purchased separately)
•
Hardwire Version comes complete with watertight connector and Hardwire
Converter 24VAC to 6VDC
•
4" (102mm) Cast Electronic Faucet
COMPLIES WITH:
•
CSA certified
•
Complies to ASME A112.18.1/ CSA B125.1
•
Indicates compliance to ICC/ANSI A117.1
•
Verified compliant with 0.25% weighted average Pb content regulations
•
Patented
•
NOTE 1: For optimum performance of this product, we recommend a
system pressure between 20 and 80 PSI static. This product will operate up
to a maximum of 125 PSI static per ANSI and CSA requirements. However,
we do not recommend pressures above 80 PSI. Thermal expansion or
leaking pressure reducing valves may require use of expansion tanks or
relief valves to ensure your system never exceeds its maximum intended
pressure setting.
•
NOTE 2: Use 3-conductor 18AWG wire between transformer and hardwire
converter/driver board earth ground.
•
NOTE 3: Use Delta Commercial approved transformers and mount the
transformer a minimum of 6 inches away from the Delta driver board
enclosure.
•
NOTE 4: Refer to Proximity Application Notes for installation best practices,
proper grounding and wiring diagrams on www.specselect.com.
•
NOTE 5: High temperature disinfection cycles not recommended for #8
Control Box as the thermostatic mixing valve limits the higher temperature
water flow output.
•
NOTE 3: Hardwire Proximity models not for use on enamel covered metal
sinks
•
Outlet options 2,3 and 4 are EPA WaterSense listed
•
(Contact Delta Representative for State and/or Local Approvals)
(Dimensional drawing on following page)
•
Hands free (touchless) operation.
•
No visible sensor, the spout is the sensor.
•
Water flows when sensing is activated.
•
Water flow stops upon de-activiation of sensing.
•
Adjustable sensing distance factory set to 76 mm (3").
•
Low battery audible beep (for battery models only) will activate after faucet
shuts off when approximately 1500 cycles remain.
•
Adjustable auto shut off feature. Factory set to 45 seconds.
•
Metering mode with selectable flow times of 7 seconds to 4 minutes, factory
set off.
•
Periodic Rinse feature, time adjustable in 6 hour increments up to 2 days.
Selectable rinsing lengths from 10 to 180 seconds. Factory set off.
OPERATION:
NOTES:
Control Box(590Txxx8TR) - NOTES:
Requires Rough-in Product Number ELAVT0008ARI to be ordered separately -
seeELAVT0008ARI
Delta reserves the right (1) to make changes to specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference.
Measurement may vary plus or minus 6mm(0.25"). Mounting locations are suggested only. Check with local codes for requirements in your area. This spec was produced January 20, 2017.
- 1.0.25277
Page of1 2
Delta Faucet Company - 55 East 111th St. - Indianapolis, Indiana, USA 46280 - [phone]
Delta Faucet Canada - 395 Matheson Blvd E - Mississauga, Ontario, Canada L4Z 2H2 - [phone]