Installation Sheet

ManualsBrandsDelta ManualsCommercial ProductsDelta Commercial 0.35 GPM Centerset Battery Operated Electronic Bathroom Faucet - Less Rough-In Valve

063125A

High-Rise Spout

Assembly for

Proximity

060765A

Wrench

061198A

Single Hole Deck

Gasket (6/pkg)

061157A

Spacer

package

for Hi-Rise

Proximity

RP6087

Nut &

Washer

RP6001

Nut & Washer

061158A

Spacer package for

4” Lavatory Proximity

061156A

4” Lavatory Spout

Gasket (6/pkg)

063126A

4” Lavatory

Spout

Assembly for

Proximity

061206A

Proximity

Sensor

Module

Page 1

209493 Rev. A

Write purchase model number here for future reference

PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc. as

items relating to ongoing maintenance suggestions and procedures are included.

060683A

24VAC to 6VDC Converter

061259A

Ground Wire Kit

(for hardwire models)

061047A

24VAC to 6VDC Converter with

Battery Backup

061256A

36” Sensor Module Extension Cable

209493 209493 209493 209493

www.specselect.com

OPTION LIST

TRANSFORMERS

060704A

Transformer 110 to 24 VAC 20VA

up to 5 Electronic Valves

060771A

Transformer 110 to 24 VAC 40VA

up to 10 Electronic Valves

060772A

Transformer 110 to 24 VAC 100VA

up to 25 Electronic Valves

DECK PLATES

061159A

4” Deck Plate & Hold-Down Pkg

061160A

8” Deck Plate & Hold-Down Pkg

060681A

Battery Holder

Model Number

591TPxxx0

591TPxxx1TR

591TPxxx8TR

590TPxxx0

590TPxxx1TR

590TPxxx8TR

Description

Battery Operated Surface Mount Box #0

Battery Operated Control Box #1 Trim

Battery Operated Control Box #8 Trim

Hard Wire Operated Surface Mount Box #0

Hard Wire Operated Control Box #1 Trim

Hard Wire Operated Control Box #8 Trim

Page #

COVER

060073A

Screws (4/pkg) and driver bit for covers

060577A

12” Stainless Steel Cover

TMV Repair Kits

061137A

Adjustment Wrench

063164A

Check Valves (2/pkg)

INSTALLATION AND SET-UP INSTRUCTIONS

063128A

Battery Box Assembly less driver

board and battery holder

060905A

Cover Gasket

060906A

Surface

Mount Housing

061252A

Dual

Driver Board

060909A

Screen Assembly

063131A

3/8” Comp Connect Nut

& Ferrile

063127A

Solenoid Valve with 3/8”

Compression Connectors

and Solenoid Holder

062032A

Braided Polymer Hose

060908A

Solenoid Holder

062032A

Braided Polymer Hose

59__TP__ __ __ __

RP6092

Nut & Washer

061159A

4” Deck Plate

& Holddown Pkg

061160A

8” Deck Plate

& Holddown Pkg

060638A

Vandal Resistant Laminar

Outlet with Antimicrobial

by Agion

1.5 GPM (5.7 L/min)

060640A

Vandal Resistant Flow

Control Aerator and Wrench

1.5 GPM (5.7 L/min)

061203A

Vandal Resistant Laminar

Outlet with Wrench

0.5 GPM (1.9 L/min)

061176A

Vandal Resistant Laminar

Outlet with Wrench

1.0 GPM (3.8 L/min)

061104A

Vandal Resistant Flow

Control Non-Aerating

Spray Outlet with Wrench

0.35 USGPM (1.3 L/min)

060642A - Optional

Flow Control Aerator

1.5 GPM (5.7 L/min)

NOTES:

For optimum performance of this product, the recommended system pressure is between

20 and 80 PSI static. This product will operate up to a maximum of 125 PSI static per

ANSI and CSA requirements. However, it is not recommended the pressure go above

80 PSI. Thermal expansion or leaking pressure reducing valves may require the use of

expansion tanks or relief valves to ensure your system never exceeds its maximum

intended pressure setting.

Control Box #0 and #1

Designed for routine 180°F (82°C) disinfection cycles up to 10 minutes.

Control Box #8

High temperature disinfection cycles not recommended for #8 control box as the thermo-

static mixing valve limits the higher temperature water flow output.

 Use 3-conductor 18AWG wire between transformer and hardwire converter / driver

board earth ground.

 Use Delta Commercial approved transformers and mount the transformer a minimum of

6” (152 mm) away from the Delta driver board enclosure.

 Refer to Proximity Application Notes on SpecSelect for installation best practices,

proper grounding and wiring diagrams.

Summary of content (18 pages)

PAGE 1
59__TP__ __ __ __ 209493 Control Box #8 High temperature disinfection cycles not recommended for #8 control box as the thermostatic mixing valve limits the higher temperature water flow output. Use 3-conductor 18AWG wire between transformer and hardwire converter / driver board earth ground. Use Delta Commercial approved transformers and mount the transformer a minimum of 6” (152 mm) away from the Delta driver board enclosure.
PAGE 2
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 591TPxxx0 Battery Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS Fig. 1 Spout STEP 1. FAUCET INSTALLATION Mount faucet to sink using the provided components in the following order - grey bottom spacer, washer, lock nut (Fig. 1).
PAGE 3
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 591TPxxx0 Battery Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS STEP 8. TEST FOR OPERATION Fig. 6 Test for operation. If OK, then close lid - Use caution not to damage wires or components on electronic driver board. Route wires through notches/ openings in the box. See Fig 6. Secure lid using screws.
PAGE 4
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 591TPxxx1TR Battery Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Typical Installation (Recessed Mount Box) If recessed box is supplied, rough in as per Figure 8. The most vandal resistant installation is when the control box is as close to the bottom of the sink as feasible.
PAGE 5
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 591TPxxx1TR Battery Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS Fig. 9 Spout STEP 5. TEST FOR OPERATION Test for operation. If OK, then close lid - Use caution not to damage wires or components on electronic driver board. Route wires through notches/openings in the box. See Fig 8. Secure lid using screws.
PAGE 6
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 591TPxxx8TR Battery Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Fig. 7 Typical Installation (Recessed Mount Box) If recessed box is supplied, rough in as per Figure 13. The most vandal resistant installation is when the control box is as close to the bottom of the sink as feasible.
PAGE 7
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 591TPxxx8TR Battery Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 5a. CONNECT ELECTRICAL SUPPLY, SOLENOID VALVE & SENSOR Fig. 14 Spout Remove valve spacer and install solenoid valve and washers with body arrow in the direction of water flow. See Fig. 16. Feed sensor wire from spout into control box and then connect to the driver board.
PAGE 8
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx0 Hard Wire Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS Fig. 19 Spout STEP 1. FAUCET INSTALLATION Mount faucet to sink using the provided components in the following order - grey bottom spacer, washer, lock nut (Fig. 19).
PAGE 9
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx0 Hard Wire Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS CONDUCTIVE SINKS Fig. 24 NON-CONDUCTIVE SINKS Fig.
PAGE 10
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx1TR Hard Wire Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Note: Wires connecting between box(es) and from transformer must be protected from abrasion and being pulled at connections. They also may have to be routed through at a later stage of construction.
PAGE 11
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx1TR Hard Wire Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS Cover STEP 4b. CALIBRATION Fig. 29 After power is applied to the driver board, it generates 5 quick beeps 3 times which prompts the installer to step away from the unit. During the calibration process, the water will turn ON for several seconds then proceed to shut off.
PAGE 12
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx8TR Hard Wire Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Fig. 34 Typical Installation (Recessed Mount Box) Note: Wires connecting between box(es) and from transformer must be protected from abrasion and being pulled at connections. They also may have to be routed through at a later stage of construction.
PAGE 13
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx8TR Hard Wire Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 5a. CONNECT ELECTRICAL SUPPLY, SOLENOID VALVE AND SENSOR Fig. 36 Remove valve spacer and install solenoid valve and washers with body arrow in the direction of water flow. See Fig. 38. Feed sensor wire from spout into control box and then connect to the driver board.
PAGE 14
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 590TPxxx8TR Hard Wire Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 7. BASIC OPERATION AFTER CALIBRATION Proximity® sensing technology works by creating an electrical field around a conductor (the spout) and monitoring the change in capacitance that the conductor undergoes.
PAGE 15
MAKING ADJUSTMENTS FOR CONTROL BOXES #0, 1 & 8 The factory defaults for all settings are shown in the Quick Reference Chart below. If these are acceptable, the driver board is ready for use. If changes are required, follow the instructions to make adjustments. DRIVER BOARD QUICK REFERENCE CHART Symbol Function Factory Default Setting Description d Sensor Sensitivity Higher numbers represent a more sensitive configuration. Higher sensitivity will increase the distance at which the user is detected.
PAGE 16
CARE INSTRUCTIONS This Delta Commercial faucet is designed and engineered in accordance with the highest quality and performance standards. With proper care, it will give years of trouble free service. Care should be given to the cleaning of this product. Although the chrome finish is extremely durable, it can be DAMAGED by ACIDIC CLEANERS (i.e. cleaners designed specifically for vitreous china lavatories and water closets), HARSH ABRASIVES or POLISH.
PAGE 17
TROUBLESHOOTING GUIDE Check to ensure faucet was installed according to the M&I sheet. Note: See attached M&I, pages 1 to 15. Test for operation. If unit does not operate: Verify spacers are in place; black spacer on top and grey spacer on the bottom of the sink or counter. Check to be sure power cable is properly secured in fitting. Check to be sure batteries are fresh and properly installed. Check two wires to solenoid to be sure they are connected correctly.
PAGE 18
Delta Commercial Faucet Limited Warranty All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book. This warranty is made to the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.