Installation Guide

ManualsBrandsDelta ManualsBath1-Spray Handheld Showerhead in White

2/3/17 Rev. B

Models/Modelos/Modèles

59348, 59310 WH 59410, 59710,

59310-WH20-PK, 59310-WH18-PK,

59348-20-PK, 59348-18-PK

Series/Series/Seria

INSTALLATION INSTRUCTIONS FOR HAND SHOWER

UNIT WITH WALL MOUNT

INSTRUCCIONES PARA LA INSTALACION DE LA UNIDAD

DE LA REGADERA DE MANO CON SOPORTE DE PARED

INSTRUCTIONS D’INSTALLATION DE LA DOUCHE À

MAIN AVEC SUPPORT MURAL

www.deltafaucet.com

72639

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

▲

Specify Finish

Especifíque el Acabado

Précisez le Fini

4 CONNECT TAPERED END OF HOSE TO HAND SHOWER

Seat the washer, if provided, firmly into the hose nut. Remove the yellow tape from the end of the hose that screws onto the hand shower.

Carefully align the thread of the tapered end of the Hose directly to the Hand Shower. Hand tighten - do not use a wrench or pliers. Then place

the Hand Shower into the wall mount.

3. INSTALL SHOWER ARM AND HAND SHOWER

It is recommended to wrap plumber tape (not included) around the threads of the shower arm only.

3A. STANDARD INSTALLATION: A washer, if provided (some of our hoses are washerless), must be firmly seated into the bottom of the

standard hex nut end of the Hose. Then firmly hand tighten the hose nut clockwise onto the water supply. DO NOT use a wrench or pliers.

If your Hose has Hose nuts, as pictured in 3A; a vacuum breaker may be required for installation.

If your hose is not equipped with a vacuum breaker, in order to make your product backflow compliant a vacuum breaker will need to be

added.

INSTALLATION WITH A VACUUM BREAKER: If a Vacuum Breaker is required for your installation, the Vacuum Breaker should be connected

to the standard hex nut of the Hose and then attach it to the Shower Arm at the water supply connection. If you attach the Vacuum

Breaker to the Hand Shower, it will not function as desired.

3B. VACUUM BREAKER HOSE INSTALLATION: Your shower hose is equipped with a Vacuum Breaker, permanently installed in the end of

your hose that has a ridged nut (as pictured in 3B). Hand tighten the ridged nut clockwise to the water supply. Do not use a wrench or

pliers. If you attach the ridged nut to the hand shower, the Vacuum Breaker will not function.

NOTE: A Vacuum Breaker is a device that is required by certain code authorities to protect your water supply from the back-flow of impure

water. The Vacuum Breaker usually discharges a small amount of water each time you turn on your shower. It may also drain water when

you shut it off. Both are normal conditions – the water is draining not leaking.

DO NOT TRY TO REMOVE OR TIGHTEN THE VACUUM BREAKER which is permanently installed into the hose. This could cause damage to

the mechanism.

1. REMOVE EXISTING SHOWER HEAD

Turn the existing shower head counter-clockwise with adjustable wrench or pliers. Use care not to unscrew the shower arm; hold the shower

arm secure. Note: If your shower arm has a ball on the end of it, it will not work with this shower unit and will need to be replaced with a

standard shower arm.

2. INSTALL WALL MOUNT

Select wall position desired for your hose length. Prior to mounting, hold up the gray mounting base with the circular handle in an ”up” position.

Determine type of mount for your application. For mounting into Tile: Drill 1/4” holes in grout (if possible) and use enclosed anchors and screw

mount to base. For mounting into Fiberglass/Acrylic: Drill 1/4” holes (larger if needed for specific toggle bolts) in wall and install with small

toggle bolts (not supplied).

For Adhesive Mounting: Clean the surface area with extra-fine steel wool; then apply rubbing alcohol or fingernail polish remover to prepare the

surface and wipe clean. Caution: The first position must be correct, as you cannot move the mount after adhering to the surface. Peel off the

green backing film and position holder upright. Press firmly into place. ALLOW 24 HOURS BEFORE USING. Snap shell cover over the base on the

wall.

1. 2. 3. 4.

Ridged

Nut

= 3A

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR HAND SHOWER UNIT WITH WALL MOUNT 72639 INSTRUCCIONES PARA LA INSTALACION DE LA UNIDAD DE LA REGADERA DE MANO CON SOPORTE DE PARED Models/Modelos/Modèles 59348, 59310 WH 59410, 59710, 59310-WH20-PK, 59310-WH18-PK, 59348-20-PK, 59348-18-PK Series/Series/Seria INSTRUCTIONS D’INSTALLATION DE LA DOUCHE À MAIN AVEC SUPPORT MURAL Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1. 2. 3. 4. Tuerca estriada = 3A = 3B 1. QUITE LA CABEZA DE LA REGADERA VIEJA Gire la cabeza de la regadera vieja en sentido inverso a las agujas del reloj con una llave o pinzas. Tenga cuidado de no aflojar el brazo de la regadera; sosténgalo de manera segura. Nota: Si el brazo de la regadera tiene una bola en el extremo, no funcionará con esta regadera y necesitará reemplazarla con una montura estándar para el brazo de la regadera. 2.
PAGE 3
1. 2. 3. 4. Écrou cannelé = 3A = 3B 1. RETRAIT DE LA POMME DE DOUCHE EXISTANTE Tournez la pomme de douche existante dans le sens inverse des aiguilles d’une montre avec une clé ou une paire de pinces. Prenez soins de ne pas dévisser le bras de douche en maintenant le bras fixe. Note : Cette unité de douche ne peut pas être utilisée si l’embout du bras de douche est de type sphérique. Vous devrez remplacer le bras de douche par un bras de douche standard. 2.
PAGE 4
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.