Installation Sheet

ManualsBrandsDelta ManualsCommercial ProductsDelta Commercial 1 GPM Single Hole Hardwire Operated Electronic Faucet with Gooseneck Spout - Less Rough-In Valve

063222A / 063222SS

Proximity Gooseneck

Spout Assembly

0.5 GPM (1.9 L/min)

063226A / 063226SS

Proximity Gooseneck

Spout Assembly

1.0 GPM (3.8 L/min)

063227A / 063227SS

Proximity Gooseneck

Spout Assembly

1.5 GPM (5.7 L/min)

063229A / 063229SS

Proximity Gooseneck

Spout Assembly

2.2 GPM (8.3 L/min)

RP6087

Nut & Washer

061206A

Proximity

Sensor Module

Page 1

209257 Rev. A

62__TP3__ __ __

Write purchase model number here for future reference

PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc. as

items relating to ongoing maintenance suggestions and procedures are included.

060683A

24VAC to 6VDC Converter

061259A

Ground Wire Kit

(for hardwire models)

061047A

24VAC to 6VDC Converter with

Battery Backup

061256A

36” Sensor Module Extension Cable

062032A

Braided Polymer Hose

061266A

Laminar Outlet (3/pkg, 1 key)

0.5 GPM (1.9 L/min)

061267A

Laminar Outlet (3/pkg, 1 key)

1.0 GPM (3.8 L/min)

061268A

Laminar Outlet (3/pkg, 1 key)

1.5 GPM (5.7 L/min)

061296A

Laminar Outlet (3/pkg, 1 key)

2.2 GPM (8.3 L/min)

NOTES:

For optimum performance of this product, we recommend

a system pressure between 20 and 80 PSI static. This

product will operate up to a maximum of 125 PSI static

per ANSI and CSA requirements. However, we do not

recommend pressure above 80 PSI. Thermal expansion

or leaking pressure reducing valves may require use of

expansion tanks or relief valves to ensure your system

never exceeds its maximum intended pressure setting.

Control Box #0 and #1

Designed for routine 180°F (82°C) disinfection cycles up

to 10 minutes.

Control Box #8

High temperature disinfection cycles not recommended

for #8 control box as the thermostatic mixing valve limits

the higher temperature water flow output.

 Use 3-conductor 18AWG wire between transformer

and hardwire converter / driver board earth ground.

 Use Delta Commercial approved transformers and

mount the transformer a minimum of 6” (152 mm) away

from the Delta driver board enclosure.

 Refer to Proximity Application Notes for installation

best practices, proper grounding and wiring diagrams.

209257 209257 209257 209257

www.specselect.com

OPTION LIST

TRANSFORMERS

060704A

Transformer 110 to 24 VAC 20VA

up to 5 Electronic Valves

060771A

Transformer 110 to 24 VAC 40VA

up to 10 Electronic Valves

060772A

Transformer 110 to 24 VAC 100VA

up to 25 Electronic Valves

DECK PLATES

061269A / 061269SS

4” Deck Plate & Hold-Down Pkg

061270A / 061270SS

8” Deck Plate & Hold-Down Pkg

061295A

Nut & Washer

061269A

061269SS

4” Deck Plate

& Holddown Pkg

061270A

061270SS

8” Deck Plate

& Holddown Pkg

061294A

Single Hole

Deck Gasket

for Proximity

Gooseneck

(6/pkg)

061293A

Spacer package for

Proximity Gooseneck

060681A

Battery Holder

063128A

Battery Box Assembly less driver

board and battery holder

060905A

Cover Gasket

060906A

Surface

Mount Housing

061252A

Dual

Driver Board

063127A

Solenoid Valve with 3/8”

Compression Connectors

and Solenoid Holder

060908A

Solenoid Holder

060909A

Screen Assembly

063131A

3/8” Comp Connect Nut

and Ferrile

Model Number

621TPxxx0

621TPxxx1TR

621TPxxx8TR

620TPxxx0

620TPxxx1TR

620TPxxx8TR

Description

Battery Operated Surface Mount Box #0

Battery Operated Control Box #1 Trim

Battery Operated Control Box #8 Trim

Hard Wire Operated Surface Mount Box #0

Hard Wire Operated Control Box #1 Trim

Hard Wire Operated Control Box #8 Trim

Page #

COVER

060073A

Screws (4/pkg) and driver bit for covers

060577A

12” Stainless Steel Cover

TMV Repair Kits

061137A

Adjustment Wrench

063164A

Check Valves (2/pkg)

INSTALLATION AND SET-UP INSTRUCTIONS

Summary of content (18 pages)

PAGE 1
62__TP3__ __ __ 061296A Laminar Outlet (3/pkg, 1 key) 2.2 GPM (8.3 L/min) 063227A / 063227SS Proximity Gooseneck Spout Assembly 1.5 GPM (5.7 L/min) 063229A / 063229SS Proximity Gooseneck Spout Assembly 2.2 GPM (8.3 L/min) 209257 061269A 061269SS 4” Deck Plate & Holddown Pkg 061270A 061270SS 8” Deck Plate & Holddown Pkg NOTES: 209257 For optimum performance of this product, we recommend a system pressure between 20 and 80 PSI static.
PAGE 2
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 621TPxxx0 Battery Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS Fig. 1 Spout STEP 1. FAUCET INSTALLATION Mount faucet to sink using the provided components in the following order - grey bottom spacer, washer, lock nut (Fig. 1).
PAGE 3
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 621TPxxx0 Battery Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS STEP 8. TEST FOR OPERATION Test for operation. If OK, then close lid - Use caution not to damage wires or components on electronic driver board. Route wires through notches/ openings in the box. See Fig 6. Secure lid using screws. If faucet leaks from spout outlet: SHUT OFF WATER SUPPLIES.
PAGE 4
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 621TPxxx1TR Battery Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Note: Wires connecting between box(es) and from transformer must be protected from abrasion and being pulled at connections. They also may have to be fished through at a later stage of construction.
PAGE 5
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 621TPxxx1TR Battery Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 4b. CALIBRATION Fig. 9 Spout After power is applied to the driver board, it generates 5 quick beeps 3 times which prompts the installer to step away from the unit. During the calibration process, the water will turn ON for several seconds then proceed to shut off.
PAGE 6
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 621TPxxx8TR Battery Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Note: Wires connecting between box(es) and from transformer must be protected from abrasion and being pulled at connections. They also may have to be fished through at a later stage of construction.
PAGE 7
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 621TPxxx8TR Battery Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 5a. CONNECT ELECTRICAL SUPPLY, SOLENOID VALVE & SENSOR Fig. 14 Spout IMPORTANT: ENSURE THAT WATER SUPPLY IS ON BEFORE PROCEEDING.
PAGE 8
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx0 Hard Wire Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS Fig. 19 Spout STEP 1. FAUCET INSTALLATION Mount faucet to sink using the provided components in the following order - grey bottom spacer, washer, lock nut (Fig. 19).
PAGE 9
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx0 Hard Wire Operated Surface Mount Box #0 INSTALLATION AND SET UP INSTRUCTIONS CONDUCTIVE SINKS Fig. 24 NON-CONDUCTIVE SINKS Fig.
PAGE 10
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx1TR Hard Wire Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Note: Wires connecting between box(es) and from transformer must be protected from abrasion and being pulled at connections. They also may have to be fished through at a later stage of construction.
PAGE 11
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx1TR Hard Wire Operated Control Box #1 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 4b. CALIBRATION Fig. 29 Cover Spout After power is applied to the driver board, it generates 5 quick beeps 3 times which prompts the installer to step away from the unit. During the calibration process, the water will turn ON for several seconds then proceed to shut off.
PAGE 12
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx8TR Hard Wire Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 1. ROUGH IN Note: Wires connecting between box(es) and from transformer must be protected from abrasion and being pulled at connections. They also may have to be fished through at a later stage of construction.
PAGE 13
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx8TR Hard Wire Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 5a. CONNECT ELECTRICAL SUPPLY, SOLENOID VALVE AND SENSOR Remove plastic threaded spacer nipple and install solenoid valve and washers with body arrow in the direction of water flow. See Fig. 38. Feed sensor wire from spout into control box and then connect to the driver board.
PAGE 14
Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. 620TPxxx8TR Hard Wire Operated Control Box #8 Trim INSTALLATION AND SET UP INSTRUCTIONS STEP 8. BASIC OPERATION AFTER CALIBRATION Proximity® sensing technology works by creating an electrical field around a conductor (the spout) and monitoring the change in capacitance that the conductor undergoes.
PAGE 15
MAKING ADJUSTMENTS FOR CONTROL BOXES #0, 1 & 8 The factory defaults for all settings are shown in the Quick Reference Chart below. If these are acceptable, the driver board is ready for use. If changes are required, follow the instructions to make adjustments. DRIVER BOARD QUICK REFERENCE CHART Symbol Function Factory Default Setting Description d Sensor Sensitivity Higher numbers represent a more sensitive configuration. Higher sensitivity will increase the distance at which the user is detected.
PAGE 16
CARE INSTRUCTIONS This Delta Commercial faucet is designed and engineered in accordance with the highest quality and performance standards. With proper care, it will give years of trouble free service. Care should be given to the cleaning of this product. Although the chrome finish is extremely durable, it can be DAMAGED by ACIDIC CLEANERS (i.e. cleaners designed specifically for vitreous china lavatories and water closets), HARSH ABRASIVES or POLISH.
PAGE 17
TROUBLESHOOTING GUIDE Check to ensure faucet was installed according to the M&I sheet. Note: See attached M&I, pages 1 to 15. Test for operation. If unit does not operate: Verify spacers are in place; black spacer on top and grey spacer on the bottom of the sink or counter. Check to be sure power cable is properly secured in fitting. Check to be sure batteries are fresh and properly installed. Check two wires to solenoid to be sure they are connected correctly.
PAGE 18
Delta Commercial Faucet Limited Warranty All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book. This warranty is made to the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.