Installation Guide

ManualsBrandsDelta ManualsKitchenTrinsic Single-Handle Pull-Down Sprayer Kitchen Faucet in Chrome Featuring MagnaTite Docking

HIGH-RISE PULL-DOWN KITCHEN

AND BAR / PREP FAUCETS

LLAVES DE AGUA ELEVADAS,

DESLIZABLES HACIA ABAJO,

PARA COCINAS Y BARES / PREP

ROBINET À COL DE CYGNE ET

BEC-DOUCHETTE POUR ÉVIER

DE BAR OU D’ÎLOT DE CUISINE

Models/Modelos/Modèles

9159-DST & 9959-DST

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

SILICONE

Icons

3/26/13 Rev. C

ASME A112.18.1 / CSA B125.1

ICC/ANSI A117.1

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave

Delta

usted necesitará:

•LEER TODAS las instrucciones completamente

antes de empezar.

•LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your

Delta

faucet you will need:

•ToREAD ALL the instructions completely before

beginning.

•  To  READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet

Delta

facilement, vous devez:

•LIRE TOUTES les instructions avant de débuter;

•LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

TRINSIC™

70529

Summary of content (8 pages)

PAGE 1
HIGH-RISE PULL-DOWN KITCHEN AND BAR / PREP FAUCETS LLAVES DE AGUA ELEVADAS, DESLIZABLES HACIA ABAJO, PARA COCINAS Y BARES / PREP ROBINET À COL DE CYGNE ET BEC-DOUCHETTE POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE 70529 ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 Models/Modelos/Modèles 9159-DST & 9959-DST Series/Series/Seria TRINSIC™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
RP71656▲ Bar Spout Assembly with Magnet Ensamble del Tubo de Salida Bec Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly.
PAGE 4
1 B. A. 3 2 2 2 1 1 2 2 Mount Faucet to Deck A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/4" (35 mm +/- 6 mm) and a deck thickness of up to 3" (76 mm). Install gasket (1) into groove under faucet base (2). Insert faucet tubes and shank through mounting hole in sink; and, place faucet over mounting hole. Note: With 10 1/2" escutcheon, maximum deck thickness is reduced to 2 3/4" (69.8 mm). Instale la Llave de Agua en el Borde A.
PAGE 5
OPTIONAL / OPCIONAL / FACULTATIVE 2 1 4 2 1 5 3 3 4 2 2 3 4 2 4 5 5 5 4 6 2 6 Optional Escutcheon Installation For optional installations using the 10 1/2" escutcheon, order RP64070 (specify finish) not supplied. Place the 10 1/2" escutcheon (1) and gasket (2) under faucet base. Mount as shown above using the 2 1/4-20 studs (3), nuts and washers (4), mounting nut and washer (5). Tighten mounting nut (5) securely by hand. Then, using a Phillips screwdriver, tighten locking screws (6).
PAGE 6
3 A. B. 2 OR 2 1 O 2 OU 3 1 4 3 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 7
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 8
A. 4 B. 3 2 3 1 2 7 5 4 6 5 OR 4 1 1 1 Maintenance A. Turn on hot and cold water supplies (1). Pull the hose assembly (2) out of the spout. Be sure to hold the end of the hose down into the sink and turn faucet handle (3) to the mixed position. (Tilt handle back to turn on.) Flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. Install the sprayer (4) and discard blue clip (5). B. Check all connections at arrows for leaks.