Installation Guide

ManualsBrandsDelta ManualsKitchenTrinsic Single-Handle Pull-Down Sprayer Kitchen Faucet Featuring Touch2O Technology in Chrome

HIGH-RISE, PULL-DOWN KITCHEN AND BAR / PREP,

TOUCH FAUCETS

LLAVES DE AGUA – GRIFOS DE CUELLO CISNE

EXTRAÍBLES DE FUNCIÓN AL TACTO PARA COCINA Y

BAR/PREP

ROBINETS TACTILES À BEC HAUT RÉTRACTABLE

POUR ÉVIER DE CUISINE ET DE BAR OU D’ÎLOT

Model/Modelo/Modèle

9159T-DST & 9959T-DST

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

10/30/12 Rev. D

ASME A112.18.1 / CSA B125.1

ICC/ANSI A117.1

Para instalación fácil de su llave

Delta

usted necesitará:

•LEER TODAS las instrucciones completamente

antes de empezar.

•LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALL the instructions completely

before beginning.

•  To  READ ALL warnings, care, and

maintenance information.

Pour installer votre robinet

Delta

facilement, vous devez:

•LIRE TOUTES les instructions avant de débuter;

•LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

TRINSIC

70530

WARNING: THIS FAUCET IS NOT TO BE USED WITH

PORTABLE DISHWASHERS! / ADVERTENCIA: ¡SESTA

LLAVE NO SE DEBE UTILIZAR CON MAQUINAS

LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF

SUR CE ROBINET!

Notice

Property damage and water leak possible. Incorrectly installed or unapproved swivel clip may

cause water leaks and property damage. Follow instructions to install swivel clip provided with

this faucet.

Property damage and water leak possible. Incorrectly installed or unapproved clip and hose

may cause water leaks and property damage. Follow instructions to install hose and clip

provided with this faucet.

Property damage and water leak possible. Incorrectly installed or unapproved check valve

assemblies may cause water leaks and property damage. Follow instructions to install check

valve assemblies provided with this faucet.

Property damage and water leak possible. Incorrectly installed or unapproved plastic sleeve

may cause water leaks and property damage. Follow instructions to custom ﬁt using plastic

sleeve provided with this faucet before making ﬁnal connections and turning on the supplies.

Property damage and water leak possible. Leaks and property damage may occur from

incorrect installation. Follow all installation instructions before making ﬁnal connections and

turning on the supplies.

Aviso

Es posible que se produzcan daños a la propiedad y fugas o ﬁltraciones de agua. El gancho

giratorio mal instalado o no aprobado puede causar fugas de agua y daños a la propiedad.

Siga las instrucciones para instalar el gancho giratorio provisto con esta llave de agua.

Es posible que se produzcan daños a la propiedad y fugas o ﬁltraciones de agua. El gancho o

la manguera mal instalada o no aprobada puede causar fugas de agua y daños a la propiedad.

Siga las instrucciones para instalar la manguera y el gancho provisto con esta llave de agua.

Es posible que se produzcan daños a la propiedad y fugas o ﬁltraciones de agua. El ensamble

de la llave de paso incorrectamente instalado o no aprobado puede causar fugas de agua y da-

ños a la propiedad. Siga las instrucciones para instalar el ensamble de la llave de paso provisto

con esta llave de agua.

Es posible que se produzcan daños a la propiedad y fugas o ﬁltraciones de agua. El

manguito plástico incorrectamente instalado o no aprobado puede causar fugas de agua y

daños a la propiedad. Siga las instrucciones para instalar el manguito plástico provisto con

esta llave de agua antes de hacer las conexiones ﬁnales y abrir el suministro de agua.

Posibles daños a la propiedad y ﬁltración de agua. Las ﬁltraciones o fugas de agua y daños

a la propiedad pueden ocurrir por una instalación incorrecta . Siga todas las instrucciones de

instalación antes de hacer las conexiones ﬁnales y abrir los suministros de agua.

Avis

Possibilité de dommages matériels et de fuite. Une mauvaise installation de l’agrafe pivotante

ou l’utilisation d’une agrafe pivotante non approuvée peut entraîner une fuite et des dommages

matériels. Installez l’agrafe pivotante fournie avec ce robinet conformément aux instructions.

Possibilité de dommages matériels et de fuite. Une mauvaise installation du tuyau souple

et de l’agrafe ou l’utilisation d’un tuyau souple et d’une agrafe non approuvés peut entraîner

une fuite et des dommages matériels. Installez le tuyau souple et l’agrafe fournis avec ce

robinet conformément aux instructions.

Possibilité de dommages matériels et de fuite. Une mauvaise installation des clapets de

non-retour ou l’installation de clapets de non-retour non approuvés peut entraîner des fuites

et des dommages matériels. Installez les clapets de non-retour fournis avec ce robinet

conformément aux instructions.

Possibilité de dommages matériels et de fuite. Une mauvaise installation du manchon en

plastique ou l’installation d’un manchon en plastique non approuvé peut entraîner des fuites

et des dommages matériels. Installez le manchon en plastique fourni avec ce robinet confor-

mément aux instructions pour l’installation sur mesure avant de faire les branchements ﬁnals

et d’ouvrir les robinets

Possibilité de dommages matériels et de fuite. Une mauvaise installation peut entraîner

une fuite et des dommages matériels. Effectuez l’installation conformément à toutes les

instructions avant de faire les branchements ﬁnals et d’ouvrir les robinets d’alimentation.

SILICONE

Icons

You may need: / Usted puede necesitar:

Articles dont vous pouvez avoir besoin :

SILICONE

Icons

www.deltafaucet.com

Summary of content (16 pages)

PAGE 1
70530 ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 Model/Modelo/Modèle 9159T-DST & 9959T-DST Series/Series/Seria TRINSIC® Notice Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
RP71656▲ Bar Spout Assembly with Magnet Ensamble del Tubo de Salida Bec RP71655▲ Kitchen Spout Assembly with Magnet Ensamble del Tubo de Salida Bec ▲Specify Finish ▲Especifíque el Acabado ▲Précisez le Fini RP64069▲ Sprayer Assembly Ensamble de rociador Pulvérisateur RP60923 Retainer Funda Douille RP64070▲ Optional 10 1/2" Escutcheon, Mounting Screws (2), gasket, Nuts (2) & Washers (2) Chapa opcional de 10 1/2", Tornillos para la Instalación (2) y Empaque Plaque de finition facultative de 10 1/2 po, vis de
PAGE 4
Backflow Protection System Other useful accessories that may be purchased separately. Otros accesorios útiles que se pueden comprar por separado. Autres accessoires utiles pouvant être achetés séparément. Your Delta® faucet pull-down spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1.
PAGE 5
1 Top Mount Sinks / Instalación por Encima / Bâti supérieur A. B. C. 5 3 2 1 1 1/4" Min. From Center Line To Sink Bowl. 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 3 2 2 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette. 4 1 4 3 A 4 Spout Installation For Top Mount Sinks A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/8" (35 mm +/- 3 mm) and a deck thickness of up to 2 3/4" (69.8 mm).
PAGE 6
1 Under Mount Sinks / Instalación por Debajo / Sous le bâti A. C. B. 1 3 4 3 3 2 1 1 1/4" Min. From Center Line To Sink Bowl. 2 4 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 4 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette. 1 5 5 5 5 A Spout Installation For Under Mount Sinks A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/8" (35 mm +/- 3 mm) and a deck thickness of up to 2 1/2" (63.5 mm).
PAGE 7
A. 2 OPTIONAL / OPCIONAL / FACULTATIVE 1 Incorrect Installations 2 Instalacións incorrecta 3 Installations incorrecte 10 3 1 10 6 2 11 8 10 4 9 5 1 8 7 7 9 3 3 Optional Escutcheon Installation For optional installations using the 10 1/2" escutcheon, order RP64070 not supplied (specify finish). SHUT OFF WATER SUPPLIES. Slide escutcheon (1) and gasket (2) over tubes and place on bottom of faucet.
PAGE 8
B. Incorrect Installations 1 4 Instalacións incorrecta Installations incorrecte A. 3 B. 2 1 1 1 1 2 2 4 1 2 2 D. 1 1 3 4 4 3 1 3 1 4 2 1 3 5 A. Leave blue clip (1) installed on hose to prevent from being pulled into spout during installation. Remove blue clip and discard after flushing lines. Slide hose weight (2) over end of hose (3). B. Push hose end (1) onto solenoid assembly outlet (2). Attach clip (3) over hoses as shown.
PAGE 9
4 B. A. 3 2 3 1 4 4 3 5 5 3 Wire Connections B. Wire extension (3), extending from faucet shank, is shipped with a protective A. Briefly touch the cold stop or other ground with hand to dissipate any static plastic cap (4). Remove this by grasping the plug and pulling off the cap. Discard cap. Connect wire (3) to port (5) on the solenoid assembly. Avoid twisting wires together or placing the wires close to each other. charge.
PAGE 10
5 B. A. 6 A. 1 3 B. 2 2 1 Water Line Connections A. Important: To ensure proper opera- tion of your plumbing it is essential to install these check valve assemblies onto your supply stops. Insert ferrule (1) into cold water stop. B. Thread on check valve (2) and tighten. DO NOT OVERTIGHTEN. Repeat steps A & B for hot water stop. 3 Notice Property damage and water leak possible. Incorrectly installed or unapproved check valve assemblies may cause water leaks and property damage.
PAGE 11
C. D. 2 1 4 3 1 OR 2 O 3 2 4 OU 1 2 C. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to check valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 12
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 13
7 B. A. 2 3 2 1 1 B. Install the spray head (1) and remove blue clip (2) from hose. Check all Notice connections at arrows for leaks. Re-tighten if necessary, but do not overtighten. Sprayer will lock into position when brought into proximity of the spout magnet. The sprayer can be removed by either pulling directly out from the spout or by twisting 90° in either direction which will cause the magnets to repel and the head to decouple from the spout (recommended).
PAGE 14
1 7 4 3 8 6 4 3 5 2 Maintenance If faucet exhibits very low flow – Unscrew hose from spray head and clean debris from screen (1) (the screen is located just inside the spray) . IMPORTANT: Reinstall screen to the spray head (failure to reinstall the screen could damage internal parts). If faucet leaks from under handle or from spout outlet – Insert a small screwdriver into slot (2) in button (3) and remove. Loosen set screw (4) inside of handle. Remove handle.
PAGE 15
Cleaning the Screen / Filtro de Limpieza: / Nettoyage du filtre 3 2 1 C. A. * 2 2 2 1 1 1 1 1 D. B. 3 2 1 2 2 2 4 1 AA AA AA SHUT OFF WATER SUPPLIES. Check and clean screen (1) located in solenoid valve (2). 3 CIERRE LOS SUMINISTROS DE AGUA. Compruebe y limpie la pantalla (1) situada en la válvula electromagnética (2). FERMEZ LES ROBINETS D’ALIMENTATION. Vérifiez et nettoyez l’écran (1) situé dans la vanne électromagnétique (2).
PAGE 16
Solenoid Troubleshooting 1. If your spout flashes a red light on then off and then keeps repeating this, replace the batteries. If the spout still flashes a red light, please replace solenoid and electronics kit**. (see manual bypass of electronics section*) 3. If your LED base indicator is not displaying any lights, a. Check to make sure the spout connector, is attached to the spout and the wire from the solenoid / electronics kit.