Installation Instructions

ManualsBrandsDelta ManualsKitchenTrinsic Single-Handle Pull-Down Sprayer Kitchen Faucet Featuring Touch2O Technology in Chrome

HIGH-RISE, PULL-DOWN KITCHEN

AND BAR / PREP, TOUCH FAUCETS

LLAVES DE AGUA – GRIFOS DE CUELLO

CISNE EXTRAÍBLES DE FUNCIÓN AL

TACTO PARA COCINA Y BAR/PREP

ROBINETS TACTILES À BEC HAUT

RÉTRACTABLE POUR ÉVIER DE CUISINE

ET DE BAR OU D’ÎLOT

Model/Modelo/Modèle

9159T-DST & 9959T-DST

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

12/9/11 Rev. B

ASME A112.18.1 / CSA B125.1

ICC/ANSI A117.1

You may need

Usted puede necesitar

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave

Delta

usted necesitará:

sLEER TODAS las instrucciones completamente

antes de empezar.

sLEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your

Delta

faucet you will need:

s4OREAD ALL the instructions completely

before beginning.

s4OREAD ALL warnings, care, and

maintenance information.

Pour installer votre robinet

Delta

facilement, vous devez:

sLIRE TOUTES les instructions avant de débuter;

sLIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

WARNING: THIS FAUCET IS NOT TO BE USED WITH

PORTABLE DISHWASHERS! / ADVERTENCIA: ¡SESTA

LLAVE NO SE DEBE UTILIZAR CON MAQUINAS

LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF

SUR CE ROBINET!

TRINSIC

™

70530

Summary of content (16 pages)

PAGE 1
HIGH-RISE, PULL-DOWN KITCHEN AND BAR / PREP, TOUCH FAUCETS LLAVES DE AGUA – GRIFOS DE CUELLO CISNE EXTRAÍBLES DE FUNCIÓN AL TACTO PARA COCINA Y BAR/PREP ROBINETS TACTILES À BEC HAUT RÉTRACTABLE POUR ÉVIER DE CUISINE ET DE BAR OU D’ÎLOT 70530 ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 Model/Modelo/Modèle 9159T-DST & 9959T-DST Series/Series/Seria TRINSIC™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
DELTA® ELECTRONIC FAUCET LIMITED WARRANTY All parts and finishes of the Delta® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for a period of 5 years. Delta Faucet Company recommends using a professional plumber for all installation & repair. Delta will replace, FREE OF CHARGE, during the warranty period, any part or finish that proves defective in material and/or workmanship under normal installation, use & service.
PAGE 3
RP71656▲ Bar Spout Assembly with Magnet Ensamble del Tubo de Salida Bec RP71655▲ Kitchen Spout Assembly with Magnet Ensamble del Tubo de Salida Bec ▲Specify Finish ▲Especifíque el Acabado ▲Précisez le Fini RP64069▲ Sprayer Assembly Ensamble de rociador Pulvérisateur RP60923 Retainer Funda Douille RP64070▲ Optional 10 1/2" Escutcheon, Mounting Screws (2), gasket, Nuts (2) & Washers (2) Chapa opcional de 10 1/2", Tornillos para la Instalación (2) y Empaque Plaque de finition facultative de 10 1/2 po, vis d
PAGE 4
Backflow Protection System Other useful accessories that may be purchased separately. Otros accesorios útiles que se pueden comprar por separado. Autres accessoires utiles pouvant être achetés séparément. Your Delta® faucet pull-down spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1.
PAGE 5
1 Top Mount Sinks / Instalación por Encima / Bâti supérieur A. B. C. 5 3 2 1 1 1/4" Min. From Center Line To Sink Bowl. 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 3 2 2 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette. 4 1 4 3 A 4 Spout Installation For Top Mount Sinks A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/8" (35 mm +/- 3 mm) and a deck thickness of up to 2 3/4" (69.8 mm).
PAGE 6
1 Under Mount Sinks / Instalación por Debajo / Sous le bâti A. C. B. 1 3 4 3 3 2 1 1 1/4" Min. From Center Line To Sink Bowl. 2 4 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 4 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette. 1 5 5 5 5 A Spout Installation For Under Mount Sinks A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/8" (35 mm +/- 3 mm) and a deck thickness of up to 2 1/2" (63.5 mm).
PAGE 7
OPTIONAL / OPCIONAL / FACULTATIVE 2 1 2 3 10 3 1 3 10 6 2 11 8 4 9 1 4 10 5 5 5 6 8 7 9 7 6 Optional Escutcheon Installation For optional installations using the 10 1/2" escutcheon, order RP64070 not supplied (specify finish). SHUT OFF WATER SUPPLIES. Slide escutcheon (1) and gasket (2) over tubes and place on bottom of faucet. Making sure the indicator light (3) is located in front, insert tubes through mounting hole in sink and center faucet in position over holes.
PAGE 8
3 A. B. 2 1 1 2 2 1 1 2 3 3 2 3 1 A. Leave blue clip (1) installed on hose to prevent from being pulled into spout B. Push hose end (1) onto solenoid assembly outlet (2). Attach clip (3) A. Deje instalado el gancho azul (1) en la manguera para evitar que esta se hale B. Empuje el extremo de la manguera (1) por la salida del montaje del sole- A. Laissez l’agrafe bleue (1) sur le tuyau souple pour éviter que celui-ci rentre B.
PAGE 9
4 B. A. 3 2 3 1 4 4 3 5 5 3 Wire Connections B. Wire extension (3), extending from faucet shank, is shipped with a protective A. Briefly touch the cold stop or other ground with hand to dissipate any static plastic cap (4). Remove this by grasping the plug and pulling off the cap. Discard cap. Connect wire (3) to port (5) on the solenoid assembly. Avoid twisting wires together or placing the wires close to each other. charge.
PAGE 10
5 B. A. 3 2 1 3 A. Connect battery cable (1) to battery box (2). Install 6 “AA” batteries (3) into the B. Place battery pack in a convenient location close to the ﬂoor. A. Conecte el cable de batería (1) a la caja de la batería (2). Cargue 6 baterías B. Coloque el paquete de las baterías en una ubicación A. Connectez le câble du boîtier de piles (1) au boîtier de piles (2). Placez 6 B. Placez le boîtier de piles dans un endroit accessible près du battery box (2).
PAGE 11
6 C. A. D. 1 3 2 1 OR 4 B. O 2 3 1 2 2 4 OU 1 2 Water Line Connections A. Important: To ensure proper operation of your plumbing it is essential to install these check valve assemblies onto your supply stops. Insert ferrule (1) into cold water stop. B. Thread on check valve (2) and tighten. DO NOT OVERTIGHTEN. Repeat steps A & B for hot water stop. C. Ensure all fittings and end connections are free of debris.
PAGE 12
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet ﬁtting (4).
PAGE 13
7 B. A. 2 3 2 1 1 A. Turn on hot and cold water supplies (1). Pull the hose assembly (2) out B. Install the spray head (1) and remove blue clip (2) from hose. Check all of the spout. Be sure to hold the end of the hose down into the sink and turn faucet handle (3) to the mixed position. (Tilt handle back to turn on.) Flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. connections at arrows for leaks.
PAGE 14
1 7 4 3 6 4 3 5 2 Maintenance If faucet exhibits very low flow – Unscrew hose from spray head and clean debris from screen (1) (the screen is located just inside the spray) . IMPORTANT: Reinstall screen to the spray head (failure to reinstall the screen could damage internal parts). If faucet leaks from under handle or from spout outlet – Insert a small screwdriver into slot (2) in button (3) and remove. Loosen set screw (4) inside of handle. Remove handle.
PAGE 15
Cleaning the Screen / Filtro de Limpieza: / Nettoyage du ﬁltre 3 2 1 C. A. * 2 2 2 1 1 1 1 1 D. B. 3 2 1 2 2 2 4 1 AA AA AA SHUT OFF WATER SUPPLIES. Check and clean screen (1) located in solenoid valve (2). 3 CIERRE LOS SUMINISTROS DE AGUA. Compruebe y limpie la pantalla (1) situada en la válvula electromagnética (2). FERMEZ LES ROBINETS D’ALIMENTATION. Vérifiez et nettoyez l’écran (1) situé dans la vanne électromagnétique (2).
PAGE 16
Solenoid Troubleshooting 1. If your spout ﬂashes a red light on then off and then keeps repeating this, replace the batteries. If the spout still ﬂashes a red light, please replace solenoid and electronics kit**. (see manual bypass of electronics section*) 3. If your LED base indicator is not displaying any lights, a. Check to make sure the spout connector, is attached to the spout and the wire from the solenoid / electronics kit.