Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceVictorian Single-Handle Pull-Down Sprayer Kitchen Faucet in Venetian Bronze featuring MagnaTite Docking

SINGLE LEVER LELAND

PULL DOWN KITCHEN FAUCETS

PALANCA DESLIZABLE LELAND

PARA LLAVES DE COCINA

ROBINETS MONOCOMMANDE LELAND

À BEC-DOUCHETTE RÉTRACTABLE POUR

ÉVIER DE CUISINE

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

955-DST, 955-SD-DST, 978-DST,

978-SD-DST, 978-WE-DST,

9955-DST, 9978-DST,

16955-SD-DST & 16970-SD-DST

Series/Series/Seria

9/11/10 Rev. D

ASME A112.18.1 / CSA B125.1

MEETS OR EXCEEDS — ASME A112.18.1 / CSA B125.1

ALCANZA O EXCEDE LAS SIGIENTES NORMAS —

ASME A112.18.1 / CSA B125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR

CON MAQUINAS LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF SUR CE ROBINET!

LE ROBINET EST CONFORME OU SUPÈRIEUR AUX EXIGENCES DES

NORMES SUIVANTES: ASME A112.18.1 / CSA B125.1

1/8"

62818

62818 Rev D.indd 1 10/1/10 9:08 AM

Summary of content (12 pages)

PAGE 1
62818 UP C ® ASME A112.18.1 / CSA B125.1 SINGLE LEVER LELAND® PULL DOWN KITCHEN FAUCETS PALANCA DESLIZABLE LELAND® PARA LLAVES DE COCINA ROBINETS MONOCOMMANDE LELAND® À BEC-DOUCHETTE RÉTRACTABLE POUR ÉVIER DE CUISINE Models/Modelos/Modèles 955-DST, 955-SD-DST, 978-DST, 978-SD-DST, 978-WE-DST, 9955-DST, 9978-DST, 16955-SD-DST & 16970-SD-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Backflow Protection System Your Delta Faucet pull-down spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the spray assembly.
PAGE 3
1 2 3 * Front Frente Avant 3 2 1 4 2 1 4 1 5 6 Spout Installation Valve Assembly Installation NOTE: These faucets are designed to fit a maximum countertop thickness of 2 1/4". If you are installing the faucet on a Stainless Steel or a thin sink use RP37490 Stabilization Plate SUPPLIED WITH FAUCET. * Slide the gasket (1) up over tubes of valve assembly and place in groove in base (2). Feed tubes down through hole in sink making sure that the gasket is properly seated.
PAGE 4
3 1 A-2 B. 4 3 A-1 5 4 2 1 Insert hose through spout tip only. 7 A-3 A-4 2 7 4 3 4 8 1 3 1 1 7 5 1 8 4 6 5 1 1 Soap Dispenser Installation Hose Installation A. Screw the threaded fitting of hose (1) into spray head (2) to prevent the hose from being pulled into the spout until you are ready to flush the lines. Insert hose guide (3) into end of hose (1) as shown. Feed hose assembly (1) through spout (4) and hub (5). Slide spout assembly onto hub. Use caution not to pinch fingers.
PAGE 5
A. B. 2 2 1 OR 2 O 3 OU 1 3 4 1 2 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet ﬁtting (4).
PAGE 7
6 3 3 7 4 2 6 5 1/8" 1 4 2 2 3 1 Thread sleeve (1) over bonnet (2) and hand tighten. Place handle (3) on stem (4) and secure with set screw (5). Install button (6) into set screw hole. Turn on hot and cold water supplies (1). Pull the hose assembly (2) out of the spout and remove the spray head (3). Be sure to hold the end of the hose down into the sink and turn faucet handle (4) to the mixed position. Flush water lines for one minute.
PAGE 8
1 2 Setting The Handle Limit Stop (Optional) because it limits the amount of hot water in the mix; however, this handle limit stop will not always prevent scalding because it does not compensate for incoming pressure or sudden water temperature changes. This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory.
PAGE 9
1/8" 4 5 1 3 2 Maintenance If faucet exhibits very low flow: A. Remove and clean Aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (5) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (5) is tightened securely with a wrench.
PAGE 10
MODELS / MODELOS / MODÈLES 978-DST, 978-SD-DST & 9978-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP40650 Set Screw Tornillo de Ajuste Vis de calage RP51496 Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP60734▲ 1.5 gpm Sprayer Assembly Ensamble de rociador Pulvérisateur RP51480▲ 2.
PAGE 11
MODELS / MODELOS / MODÈLES 955-DST, 955-SD-DST, 9955-DST & 16955-SD-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP51464▲ Handle w/Button & Set Screw Manija con botón y tornillo de presión Poignée avec bouton et vis de calage RP47666 Set Screw Tornillo de Ajuste Vis de calage RP50786▲ Button Cover Botón de la cubierta Bouton de couverture RP51478▲ 2.
PAGE 12
MODEL / MODELO / MODÈLE 16970-SD-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP51512▲ Handle w/Button & Set Screw Manija con botón y tornillo de presión Poignée avec bouton et vis de calage RP23093 Set Screw Tornillo de Ajuste Vis de calage RP51513▲ Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP51511▲ Sprayer Assembly Ensamble de rociador Pulvérisateur RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & ronde