Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceLeland Single-Handle Pull-Down Sprayer Kitchen Faucet in Venetian Bronze featuring MagnaTite Docking

SINGLE LEVER PULL DOWN KITCHEN

FAUCETS

PALANCA DESLIZABLE PARA LLAVES DE

COCINA

ROBINETS MONOCOMMANDE À BEC-

DOUCHETTE RÉTRACTABLE POUR ÉVIER

DE CUISINE

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need

Usted puede necesitar

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

955-DST, 955-SD-DST, 978-DST,

978-SD-DST, 978-WE-DST, 9955-

DST, 9978-DST,

16955-SD-DST & 16970-SD-DST

Series/Series/Seria

SILICONE

Icons

3/17/16 Rev. D

WARNING: this faucet is not to be used with portable dishwashers!

ADVERTENCIA: ¡sesta llave no se debe utilizar con maquinas lavapla tos portatiles!

AVERTISSEMENT: on ne doit pas brancher un lave-vaissele portatif sur ce robinet!

SILICONE

Icons

1/8"

69900

www.deltafaucet.com

Summary of content (12 pages)

PAGE 1
69900 SINGLE LEVER PULL DOWN KITCHEN FAUCETS PALANCA DESLIZABLE PARA LLAVES DE COCINA ROBINETS MONOCOMMANDE À BECDOUCHETTE RÉTRACTABLE POUR ÉVIER DE CUISINE Models/Modelos/Modèles 955-DST, 955-SD-DST, 978-DST, 978-SD-DST, 978-WE-DST, 9955DST, 9978-DST, 16955-SD-DST & 16970-SD-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
1 2 3 * Front Frente Avant 3 Push valve to back of mounting hole. 4 2 Empuje la válvula a la parte posterior del orificio de montaje. 1 1 Poussez la soupape vers l’arrière du trou de montage 2 1 4 5 6 Spout Installation NOTE: These faucets are designed to fit a maximum thickness of 2 1/4". If you are installing the faucet on a Stainless Steel or a thin sink use RP37490 Stabilization Plate SUPPLIED WITH FAUCET.
PAGE 4
3 A-1 B. 6 1 3 2 A-2 2 Insert hose through spout tip only. A-3 6 2 6 3 3 1 7 2 2 4 6 7 2 5 4 2 Incorrect Installations. Instalacións incorrecta. Hose Installation A. Insert hose guide (1) into end of hose (2) as shown. Feed hose assembly (2) through spout (3) and hub (4). Installations incorrecte. Slide spout assembly onto hub. Use caution not to pinch fingers. Rotate spout assembly to ensure smooth operation. B. Remove hose guide (1). Slide hose weight (5) over end of hose (2).
PAGE 5
4 A. B. 2 2 OR 1 2 O 3 OU 1 4 3 1 2 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
5 6 5 3 6 5 1/8" 1 2 3 4 2 1 4 Soap Dispenser Installation Remove nut and gasket (1). Insert body (2) and gasket (3) through selected hole in sink. Make sure gasket (3) is properly seated in the base. Secure body to sink with nut and gasket (1). From under the sink screw the bottle (4) onto the body assembly shank. Insert pump and head (5) into body (2). Note: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle.
PAGE 8
7 1 2 Flush Supply Lines Because your sprayer has been factory assembled to the hose, we do not recommend removing to flush the lines. Instead, if possible, we recommend placing a bucket below the outlet fitting and one of two options: 1. With the valve in mix open position (1), slowly open and close the supply stops (2). 2. With the supply stops open (2), slowly open and close the handle in the mix position (1). This will prevent debris from being lodged in the hose and sprayer.
PAGE 9
1/8" 4 5 1 3 2 Maintenance If faucet exhibits very low flow: A. Remove and clean Aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (5) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (5) is tightened securely with a wrench.
PAGE 10
MODELS / MODELOS / MODÈLES 978-DST, 978-SD-DST & 9978-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP40650 Set Screw Tornillo de Ajuste Vis de calage RP51496▲ Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP51480▲ 1.
PAGE 11
MODELS / MODELOS / MODÈLES 955-DST, 955-SD-DST, 9955-DST & 16955-SD-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP50786▲ Button Cover Botón de la cubierta Bouton de couverture RP37039▲ Dispenser Assembly Ensamble del Dispensador Distributeur RP6052 Gasket Empaque Joint RP51503 Bonnet Bonete Chapeau RP50587 Valve Assembly
PAGE 12
MODEL / MODELO / MODÈLE 16970-SD-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP51512▲ Handle w/Button & Set Screw Manija con botón y tornillo de presión Poignée avec bouton et vis de calage RP23093 Set Screw Tornillo de Ajuste Vis de calage RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP51513▲ Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP60923 Friction Spacer