Installation Instructions

ManualsBrandsDelta ManualsKitchen ApplianceAddison Single-Handle Pull-Down Sprayer Bar Faucet in Arctic Stainless with Touch2O Technology

HIGH-RISE, PULL-DOWN KITCHEN

AND BAR / PREP, TOUCH FAUCETS

LLAVES DE AGUA ELEVADAS,

DESLIZABLES HACIA ABAJO,

PARA COCINAS Y BARES / PREP

ROBINETS TACTILES À BEC HAUT

RÉTRACTABLE POUR ÉVIER DE BAR

OU D’ÎLOT

Model/Modelo/Modèle

9192T-DST, 9992T-DST &

19922T-SSSD-DST

Series/Series/Seria

ADDISON

™

& ASHTON

™

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

8/27/10 Rev. C

ASME A112.18.1 / CSA B125.1

ICC/ANSI A117.1

You may need

Usted puede necesitar

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave

Delta

usted necesitará:

sLEER TODAS las instrucciones completamente

antes de empezar.

sLEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your

Delta

faucet you will need:

s4OREAD ALL the instructions completely

before beginning.

s4OREAD ALL warnings, care, and

maintenance information.

Pour installer votre robinet

Delta

facilement, vous devez:

sLIRE TOUTES les instructions avant de débuter;

sLIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

WARNING: THIS FAUCET IS NOT TO BE USED WITH

PORTABLE DISHWASHERS! / ADVERTENCIA: ¡SESTA

LLAVE NO SE DEBE UTILIZAR CON MAQUINAS

LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF

SUR CE ROBINET!

63218

Summary of content (16 pages)

PAGE 1
HIGH-RISE, PULL-DOWN KITCHEN AND BAR / PREP, TOUCH FAUCETS LLAVES DE AGUA ELEVADAS, DESLIZABLES HACIA ABAJO, PARA COCINAS Y BARES / PREP ROBINETS TACTILES À BEC HAUT RÉTRACTABLE POUR ÉVIER DE BAR OU D’ÎLOT 63218 ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 Model/Modelo/Modèle 9192T-DST, 9992T-DST & 19922T-SSSD-DST Series/Series/Seria ADDISON™ & ASHTON™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Cleaning and Care Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Glass cleaner can be used on SS (Stainless) finish to remove fingerprints and maintain color match.
PAGE 3
RP53879S Button Botón Bouton RP40650 Set Screw Tornillo de Presión Vis de calage RP60977S Sprayer Assembly Ensamble de rociador Pulvérisateur RP54234S Button Botón Bouton RP63194S Lever Handle Manijas de Palanca Manette RP63193S Lever Handle Manijas de Palanca Manette RP47666 Set Screw Tornillo de Presión Vis de calage RP60976S Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP60116S Cap Bonete Chapeau RP63220 Contact Assembly Chapa de Con
PAGE 4
Backflow Protection System Other useful accessories that may be purchased separately. Otros accesorios útiles que se pueden comprar por separado. Autres accessoires utiles pouvant être achetés séparément. Your Delta® faucet pull-down spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1.
PAGE 5
1 Top Mount Sinks / Instalación por Encima / Bâti supérieur A. B. C. 2 1 2 4 2 3 7 1 1/4" Min. From Center Line To Sink Bowl. 2 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 3 1 5 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette. 6 5 A 8 Determine if your sink is installed from the top of the counter or from the bottom. If your sink is installed from the top use this page for your spout installation. Spout Installation For Top Mount Sinks A.
PAGE 6
1 Under Mount Sinks / Instalación por Debajo (Typically only for solid surface counters) (Típicamente solamente para los contadores superﬁciales sólidos) (En général seulement pour les compteurs extérieurs pleins) A. / Sous le bâti B. C. 5 2 3 5 6 6 1 2 1 1/4" Min. From Center Line To Sink Bowl. 1 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 4 7 3 4 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette.
PAGE 7
10" Escutcheon / Chapa / Plaque 1 1 2.1 2 3 10 2 13 13 1 3 3 16 7 6 10 4 4 5 1 15 7 16 5 11 9 6 15 5 12 8 14 9 For 10" escutcheons: SHUT OFF WATER SUPPLIES. Slide trim ring (1) over tubes and place on bottom of faucet making sure the indicator light (2) is located in front. Remove adhesive backing from gasket (5) and press into place onto undercover plate (4). Then, assemble undercover plate (4) and escutcheon (3), and place under trim ring (1).
PAGE 8
2.2 1 A-2 B. C. 3 A-1 4 2 1 A-3 Insert hose through spout tip only. A-4 4 2 1 4 1 2 1 5 2 3 1 5 1 Hose Installation A. Screw the threaded fitting of hose (1) into spray head (2) to prevent the hose from being pulled into the spout until you are ready to flush the lines. Insert hose guide (3) into end of hose (1) as shown. Feed hose assembly (1) through spout (4) and hub (5). Slide spout assembly onto hub. Use caution not to pinch fingers.
PAGE 9
3.1 B. A. 6 6 1 1 3 2 1 3 3 1 2 4 3 5 5 3 Wire Connections B. Wire extension (3), extending from faucet base, is shipped with a protective A. Briefly touch the cold stop or other ground with hand to dissipate any static plastic cap (4). Remove this by grasping the plug and pulling off the cap. Discard cap. Connect wire (3) to port (5) on the solenoid assembly, and route through wire guide (6) keeping it away from wire (1). Avoid twisting wires together or placing the wires close to each other.
PAGE 10
3.2 B. A. 3 2 1 3 A. Connect battery cable (1) to battery box (2). Install 6 “AA” batteries (3) into the B. Place battery pack in a convenient location close to the ﬂoor. A. Conecte el cable de batería (1) a la caja de la batería (2). Cargue 6 baterías C. Pele la cubierta de plástico que queda de las tiras de Velcro A. Connectez le câble du boîtier de piles (1) au boîtier de piles (2). Placez 6 C. Retirez les pellicules de plastique restantes des bandes de battery box (2).
PAGE 11
4 C. A. 1 D. 3 1 2 4 OR B. O 2 3 1 2 2 4 OU 1 2 Water Line Connections A. Important: To ensure proper operation of your plumbing it is essential to install these check valve assemblies onto your supply stops. Insert ferrule (1) into cold water stop. B. Thread on check valve (2) and tighten. DO NOT OVERTIGHTEN. Repeat steps A & B for hot water stop. C. Ensure all fittings and end connections are free of debris.
PAGE 12
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet ﬁtting (4).
PAGE 13
5 6 2 A. B. 3 4 6 2 3 4 1 5 1 Soap Dispenser Installation Remove nut (1). Separate head (2) from body (3). Insert body (3) and gasket (4) through selected hole in sink. Make sure gasket (4) is properly seated in the base. Secure body to sink with nut (1). From under the sink screw the bottle (5) onto the body assembly shank. Insert pump (6) into head (2), then drop into body (3). NOTE: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle.
PAGE 14
3 Function Wand Mango de 3 Funciones Poignée à 3 Fonctions 7 1 2 3 Check the operation of the 2 function wand by pushing the trigger from aerator to spray. For models with a 3 function wand, check the operation by pushing the buttons to achieve the 3 different modes. Button 1 - Standard Flow Aerator Button 2 - 1.5 gpm at 60 psi Maximum Aerator Button 3 - Spray Mode Note - 3 Function Wand: Wand returns to position 2 if left in position 1 when the water is turned off.
PAGE 15
Cleaning the Screen / Filtro de Limpieza: / Nettoyage du ﬁltre 3 2 1 C. A. 1 2 2 1 1 1 1 D. B. 3 2 1 2 2 * 2 2 4 1 SHUT OFF WATER SUPPLIES. Check and clean screen (1) located in solenoid valve (2). AA AA AA CIERRE LOS SUMINISTROS DE AGUA. Compruebe y limpie la pantalla (1) situada en la válvula electromagnética (2). 3 FERMEZ LES ROBINETS D’ALIMENTATION. Vérifiez et nettoyez l’écran (1) situé dans la vanne électromagnétique (2).
PAGE 16
Solenoid Troubleshooting 1. If your spout ﬂashes a red light on then off and then keeps repeating this, replace the batteries. If the spout still ﬂashes a red light, please replace solenoid and electronics kit**. (see manual bypass of electronics section*) 3. If your LED base indicator is not displaying any lights, a. Check to make sure the spout connector, RP53233 is attached to the spout and the wire from the solenoid / electronics kit.