SHOWER BASE BASE PARA DUCHAS Model / Modelo 36” B710912-3636-WH Write purchased model number here. Retain these instructions for future use. Escriba aquí el número del modelo comprado. Conserve estas instrucciones para usarlas en el futuro. 48” B710912-4836-WH RP83757 Drain Assembly Ensamble del desagüe RP83756 Trench Grate Rejilla del desagüe 82289 www.deltafaucet.com 1 4/26/16 82289 Rev.
! REQUIREMENTS FOR SUCCESSFUL INSTALLATION KNOWLEDGE BASE: Framing Plumbing These instructions include suggestions for rough construction and plumbing installation. Local building codes vary and could supersede those suggestions. If you are not confident in your ability to perform these tasks, contract out those tasks you need help with or use a professional installer. DO NOT use drywall screws to secure flanges to wall studs. Product damage will occur and will void the warranty.
TOOLS AND MATERIALS REQUIRED • 2 x 4 lumber for additional wall studs • Rags or padding to protect product during bracing HERRAMIENTAS Y MATERIALES NECESARIOS • Madera para montantes de pared si instala el juego para pared adicionales; consulte las instrucciones de instalación del juego para pared • Conjunto de drenaje y desbordamiento que encajan en una bañera con una profundidad de 41,9 cm (16-1/2”) Drill Safety Glasses Caulk Gun Sealant (2 tubes) Tape Measure Taladro Antiparras de seguridad Pis
ROUGHING-IN • • • • Rough plumbing must be installed before base installation. Minimum stud pocket sizes are shown below. Drain cutout 5” diameter max. Right side plumbing rough-in shown. For masonry construction, floor and walls must be framed to accommodate plumbing and installation. IMPORTANT: IF INSTALLING MATCHING ENCLOSURE, refer to Enclosre Installation Manual for specific lumber sizes and placement. Additional studs will be required and need to be installed at this point.
1 1 B710912-4836-WH 1 7/16” (3.68 cm) 2 maximum máximo 5" (12.7 cm) B710912-3636-WH 2 1/8" (5.33 cm) Install Drain Pipe Position base in corner. Check for level left to right and front to back. Trace outline of drain and base. NOTE: If the base cannot be sufficiently leveled with the adjustable feet, use leveling compound to even out the surface. Ensure that the waste pipe is properly located to align with the drain assembly (not included).
1 3 4 1 1 2 3/16" (0,51cm) Attach drain following manufacturer’s instructions. Drill 3/16” holes at all stud locations on top flanges. ! ! Drill 3/16” clearance holes into flanges only. Do not drill 3/16” holes directly into studs. Drill chuck can damage base. Use an extended bit holder to reduce risk of drill chuck hitting base. Plumber’s putty will degrade base material. Do not use plumber’s putty to seal between drain and base. Use latex/acrylic sealant or a gasket.
5 6 Shim #8 x 1-1/2" (3,81cm) Finished Wall Pared terminada Insert cardboard or other material into the base to protect surface. Secure flanges to wall studs with #8 x 1-1/2” screws through previously drilled holes. Base NOTE: Gaps between flanges and studs must be less than 1/8”. Insert shims to fill gaps.
CARE AND CLEANING For regular cleaning use ONLY mild detergents or warm, soapy water. Use ONLY non-abrasive cloth or sponge. Always rinse surfaces after cleaning. Before cleaning this product with cleaning products, test a small, inconspicuous area. ! Manufacturer does not recommend the use of cleaning products that contain any of the following chemicals. Use of products containing these chemicals can cause the products to crack or discolor and will void the warranty.
LIMITED WARRANTY All parts and finishes of the Delta® Shower Base unit are warranted to the original consumer purchaser to be free from defects in material and workmanship for the time periods listed below. Delta recommends using a professional plumber for all installation and repair.
