Installation Instructions

ManualsBrandsDelta ManualsBathHycroft™ 36" x 36" White Shower Base with Center Drain

101337 Rev. A

36”

40054

B78513-3636-WH

48”

40074

B78311-4834-WH

B78513-4834-WH

60”

40094L

40094R

B78311-6032L-WH

B78311-6032R-WH

B78513-6030L-WH

B78513-6030R-WH

B78513-6032L-WH

B78513-6032R-WH

SHOWER BASE

BASE PARA DUCHAS

BASE PARA DUCHAS / REGADERAS

www.deltafaucet.com

101337

Model / Modelo / Modéle

Write purchased model number here. Retain

these instructions for future use.

Escriba aquí el número del modelo comprado.

Conserve estas instrucciones para usarlas en el futuro.

Inscrivez le numéro de modèle ici. Conservez

ces instructions pour consultation.

3/26/18

We’re here to help! Please do not return

your product to the store. For questions,

installation support, missing or replacement

parts, contact us rst.

¡Estamos aquí para servirle! Por favor, no

devuelva el producto a la tienda. Para hacer

preguntas, obtener ayuda con la instalación,

piezas que le falten o de repuesto,

contáctenos primero.

Nous sommes là pour vous aider! Ne

retournez pas votre produit au magasin. Si

vous souhaitez obtenir des renseignements,

du soutien pour l’installation ou des pièces de

rechange ou si des pièces sont manquantes,

communiquez d’abord avec nous.

www.deltafaucet.com

1-800-355-2721

consumercare@deltafaucet.com

Summary of content (10 pages)

PAGE 1
SHOWER BASE BASE PARA DUCHAS BASE PARA DUCHAS / REGADERAS Model / Modelo / Modéle 36” 40054 B78513-3636-WH Write purchased model number here. Retain these instructions for future use. Escriba aquí el número del modelo comprado. Conserve estas instrucciones para usarlas en el futuro. Inscrivez le numéro de modèle ici. Conservez ces instructions pour consultation. ? We’re here to help! Please do not return your product to the store.
PAGE 2
REQUIREMENTS FOR SUCCESSFUL INSTALLATION REQUISITOS PARA UNA INSTALACIÓN EXITOSA EXIGENCES À RESPECTER POUR RÉUSSIR L’INSTALLATION KNOWLEDGE BASE: Framing Plumbing • Confirm that your model will fit in intended location and plumbing fixtures are located where required before beginning installation. • Walls and sub-floor must be solid, plumb, and square. • Do not install in areas where temperature may drop below 32ºF (0ºC).
PAGE 3
TOOLS AND MATERIALS REQUIRED • 2 x 4 lumber for additional wall studs • Rags or padding to protect product during bracing NOTE: It is recommended to install insulation. HERRAMIENTAS Y MATERIALES NECESARIOS • Barrote de madera de 2 x 4 para los montantes de paredes adicionales • Trapos o relleno para proteger el producto durante el arriostramiento NOTA: Se recomienda instalar el aislamiento.
PAGE 4
ROUGHING-IN • • • • Rough plumbing must be installed before panel installation. Minimum stud pocket sizes are shown below. Drain cutout 5” diameter max. Right side plumbing rough-in shown. For masonry construction, floor and walls must be framed to accommodate plumbing and installation. MODEL A B 40054 17-1/8” (43.5 cm) MIN 34-3/4” (88.3 cm) B78513-3636-WH 18-3/8” (46.7 cm) MIN 36” (91.
PAGE 5
1 1 2 5" (12.7 cm) 1 3/4" (4.5 cm) Install Drain Pipe • Dry fit base and verify that it is straight and square. • Trace outline of drain and base. • Ensure that the waste pipe is properly located to align with the drain assembly (not included). • The subfloor opening should be 5” in diameter. The drain pipe should extend 1-3/4” above the subfloor. Instale la tubería del drenaje • Seque la base ajustada y verifique que esté recta y en escuadra.
PAGE 6
1 1 IF THE SUBFLOOR IS NOT FLAT AND LEVEL SI LA SUPERFICIE DE LA INSTALACIÓN NO ESTÁ NIVELADA SI LE FAUX-PLANCHER N’EST PAS PLAT ET DE NIVEAU IF THE SUBFLOOR IS NOT FLAT AND LEVEL, it is recommended to put down a mortar bed where the base will be positioned. • Apply a generous amount of mortar (1) that has been mixed to a thick consistency. Use the mortar to fill in low areas. • Place the base in the wet mortar, adjust until it is level, remove base, and let mortar cure for 24 hours.
PAGE 7
1 1 3 4 1 2 3/16" (0.5 cm) • Drill 3/16” holes at all stud locations on top flanges. • Attach drain following manufacturer’s instructions. Drill 3/16” clearance holes into flanges only. Do not drill 3/16” holes directly into studs. Drill chuck can damage base. Use an extended bit holder to reduce risk of drill chuck hitting base. NOTICE Do not use plumber’s putty to seal between drain and bathtub. Plumber’s putty will degrade bathtub material and result in product failure.
PAGE 8
1 1 5 IF THE SUBFLOOR IS NOT FLAT AND LEVEL, a mortar bed must be applied where the base will be positioned. • Apply a generous amount of mortar that has been mixed to a thick consistency. • Use the mortar to fill in low areas. • Place the base in the wet mortar and adjust until it is level. • Let mortar cure for 24 hours. • Proceed to the next step. 6 IF THE SUBFLOOR IS FLAT AND LEVEL: • Apply adhesive on floor and spread using the notched side of the trowel, starting within pencil line.
PAGE 9
CARE AND CLEANING 7 We recommend that you clean your acrylic bathing product with mild detergents. Use a terry cloth towel, soft cloth, or sponge. Avoid using abrasive scrubbing pads, steel wool, or sponges. After cleaning, rinse thoroughly with water. NOTICE When using drain cleaner or clog remover, rinse thoroughly with water. Certain chemicals and cleaners may deteriorate the acrylic surface, causing cracks and, potentially, property damage.
PAGE 10
Limited Warranty on Bathing Products This bathing product is warranted to the original consumer purchaser or commercial user, as applicable, to be free from defects in material and workmanship for the applicable period specified below: Delta®Tubs, Shower Bases, and Walls: Ten (10) years from the date of purchase by the original consumer purchaser or, for commercial users, one (1) year from the date of purchase.