Installation Guide

ManualsBrandsDelta ManualsBathClassic 500 30 in. L x 60 in. W x 72 in. H Alcove Shower Kit with Shower Wall and Shower Pan in High Gloss White

Table Of Contents

08/02/2022 Rev. A

B23205-6030-WH

B23205-6032-WH

B23207-6030-WH

B23207-6032-WH

KNOWLEDGE BASE:

Framing

Plumbing

• Confirm that your model will fit in intended location and plumbing fixtures are located where

required before beginning installation.

• Walls and sub-floor must be solid, plumb, and square.

• Do not install in areas where temperature may drop below 32ºF (0ºC).

• Allow product to reach room temperature for 30 minutes before installation.

NOTICE

These instructions include suggestions for rough construction and plumbing installation.

Local building codes vary and could supersede those suggestions. If you are not confident

in your ability to perform these tasks, contract out those tasks you need help with or use a

professional installer.

BASE DE CONOCIMIENTOS:

Encuadrado

Plomería

• Verifique que su modelo quepa en la ubicación deseada y que los accesorios de fontanería se

encuentren donde sea necesario antes de iniciar la instalación.

• Las paredes y el contrapiso deben estar firmes, nivelados y en escuadra.

• No realice la instalación en áreas donde la temperatura pueda ser inferior a 32°F (0 °C).

• Deje que el producto alcance la temperatura ambiente durante 30 minutos antes de la instalación.

AVISO

Estas instrucciones incluyen sugerencias para construcciones sin acabar e instalación de

cañerías. Los códigos locales de construcción varían según el lugar y tienen prioridad sobre

estas sugerencias. Si no se siente capaz de realizar estas tareas, tercerícelas o contrate un

instalador profesional.

BASE DE CONNAISSANCES:

Encadrement

Plomberie

• Avant de débuter l’installation, assurez-vous qu’il y a suffisamment d’espace pour le modèle que

vous voulez installer et que la plomberie est située au bon endroit.

• Les murs et le faux-plancher doivent être solides, de niveau et d’équerre.

• N’installez pas le produit à un endroit où la température peut descendre sous 32 ºF (0 ºC).

• Attendez 30 minutes avant d’installer le produit pour que celui-ci soit à la température ambiante.

AVIS

Estas instrucciones incluyen sugerencias en la construcción preliminar y la instalación de la

plomería. Los códigos locales varían de un lugar a otro y pueden tomar prioridad a estas

sugerencias. Si usted no está seguro de su habilidad para realizar estas tareas, subcontrate

en las que necesita ayuda o use un instalador profesional.

RP103265

Foam Strip

Tira de espuma

Bande de mousse

B23208-6030-WH

B23208-6032-WH

1-800-355-2721

www.deltafaucet.com/service-parts

To reference replacement parts and access additional

technical documents and product info,

visit www.deltafaucet.com

Para referencia sobre las piezas de repuesto y acceder

a documentos técnicos adicionales e información del

producto, visite www.deltafaucet.com

Pour obtenir la référence des pièces de rechange ainsi

que pour avoir accès à d’autres documents techniques et

renseignements sur le produit, allez à www.deltafaucet.com

DIRECT-TO-STUD BATHTUB WALL SET

CONJUNTO DE PARED DE TINA

DIRECTA AL MONTANTE

ENSEMBLE MURAL POUR BAIGNOIRE

FIXÉE AUX MONTANTS

113863

Regístrese en línea

S’enregistrer en ligne

www.deltafaucet.com/registerme

Model Number: ____________________

Número del modelo

Numéro de modèle

Date of Purchase: ____________________

Fecha de compra

Date d’achat

Summary of content (24 pages)

PAGE 1
13863 DIRECT-TO-STUD BATHTUB WALL SET CONJUNTO DE PARED DE TINA DIRECTA AL MONTANTE ENSEMBLE MURAL POUR BAIGNOIRE FIXÉE AUX MONTANTS Model Number: ____________________ Número del modelo Numéro de modèle Date of Purchase: ____________________ Fecha de compra Date d’achat Register Online Regístrese en línea S’enregistrer en ligne www.deltafaucet.com/registerme To reference replacement parts and access additional technical documents and product info, visit www.deltafaucet.
PAGE 2
TOOLS AND MATERIALS REQUIRED • Nominal 2 x 6 and 1 x 4 or 2 x 4 lumber for additional wall studs NOTE: It is recommended to install insulation. HERRAMIENTAS Y MATERIALES NECESARIOS • Madera nominal de 2 x 6 y 1 x 4 o 2 x 4 para pernos de pared adicionales NOTA: Se recomienda instalar el aislamiento. OUTILS ET MATÉRIEL REQUIS • Bois nominal 2 x 6 et 1 x 4 ou 2 x 4 po pour les poteaux muraux supplémentaires NOTE: Il est recommandé d’installer de l’isolant.
PAGE 3
Studs must be plumb and square. Los montantes deben estar nivelados y en escuadra. Les montants doivent être parfaitement à la verticale et d’équerre. B23205-6032-WH B23207-6032-WH B23205-6030-WH B23207-6030-WH 13 1/4” (36.6 cm) 16" (40.6 cm) 16" (40.6 cm) 13 1/4" (36.6 cm) 13 1/4” (36.6 cm) 8 3/4" (22.2 cm) 16" (40.6 cm) Horizontal 2 x 4 16" (40.6 cm) 13 1/4" (36.6 cm) Horizontal 2 x 4 20 3/4" 52.7 cm) 2 x 6 x 57” (5 x 15.24 x 145 cm) 20 3/4" 52.7 cm) 2 x 6 x 57” (5 x 15.
PAGE 4
1 Tub Door Installation Only 2 3/16” (5.6 cm) 57" (144.8 cm) 1" (2.5 cm) 1 NOTE: It is recommended to install insulation on exterior walls. It is recommended that two people install this product. Use drop cloth to protect base from damage during installation. Install Tub Door Nailers • Install additional studs (2) on each side. • Measure 1” (2.5 cm) from top of flange to locate 57” (144.8 cm) studs. Dry Fit Walls • Set back panel in position, centered in pocket.
PAGE 5
2 A. B. 1 2 1 A. Dry Fit Panels B. • Check panels for gaps and alignment. • Check that vertical side panel flanges (1) are straight and square to base. • Using a pencil, mark panel height on all wall studs. • Mark stud locations in the middle of the flanges with pencil • Remove panels. • Drill 3/16” holes at all stud locations on top flanges (1). • Drill 3/16” holes along side flanges (2) at five locations equal distance apart. Do not drill holes directly into studs. Drill chuck can damage panel.
PAGE 6
3 A. B. Back side of panel. x Parte p osterior d el panel Face arrière du panneau. y y x 1 2 A. Prepare for Plumbing Fixtures B. • Remove backing from self-adhesive pad (1). • Center pad over mixing valve hole (2) and press firmly onto back side of panel. • Using a utility knife, trim pad to reveal mixing valve hole. • Measure and mark location for plumbing fixtures on the front of the side panel. Drill pilot holes. NOTE: Hole may not be centered on panel.
PAGE 7
4 5 A. A. 4” (10.2 cm) A G 2” (5.1 cm) 2” A. Apply Foam Strip A. • Apply the adhesive-backed foam strip on the bottom of the nailing flange as shown. Form an L shape at hte front corners as shown. • Peel back the paper liner as you go, about 16” at a time as the foam is pressed onto the flange. • Press the foam into the corners and over the screws. Preparing for Back Panel A Apply adhesive to studs as shown. Ensure that beads are twice as thick as sill seal so that an adequate bond is achieved.
PAGE 8
6 A. B. 4” (10.2 cm) Tub Door Installation Only G 3” 3 po 2” 2 po A. Preparing for Side Panels G Staple sill plate gasket to studs as shown. B. Place Back Panel • Position back panel in place. Confirm that the panel is sitting down on the tub. B. Fije el panel trasero • Coloque el panel trasero en su lugar. Confirme que el panel esté asentado sobre la bañera. B. Fixez le panneau arrière. • Montez le panneau arrière. Assurez-vous qu’il est appuyé sur la baignoire.
PAGE 9
7 A. B. 1 1 S 2 3 2 A Secure Panels • Slide the side panel into the snap channel in the back panel, pressing firmly until the wall snaps into position. Repeat for other side panel. • Confirm that the wall set is sitting down on the tub, gaps are minimized, and that the vertical seams are tight. • Secure top (1) and side flanges (2) to studs with 1-1/4” truss head screws. Do not overtighten screws, this can cause panel to crack. IMPORTANT: Insert shims (3) between flanges and studs to as needed.
PAGE 10
CARE AND CLEANING We recommend that you clean your acrylic bathing product with mild detergents. Use a terry cloth towel, soft cloth, or sponge. Avoid using abrasive scrubbing pads, steel wool, or sponges. After cleaning, rinse thoroughly with water. NOTICE When using drain cleaner or clog remover, rinse thoroughly with water. Certain chemicals and cleaners may deteriorate the acrylic surface, causing cracks and, potentially, property damage.
PAGE 11
113863 Rev.
PAGE 12
Limited Warranty on Bathing Products This bathing product is warranted to the original consumer purchaser or commercial user, as applicable, to be free from defects in material and workmanship for the applicable period specified below: Delta® Tubs, Shower Bases, and Walls. Ten (10) years from the date of purchase by the original consumer purchaser or, for commercial users, one (1) year from the date of purchase. Delta® Glass and Frameless Shower Enclosures and Shower Doors.
PAGE 13
113866 DIRECT-TO-STUD BATHTUB BAÑERA DIRECTA A TUBO BAIGNOIRE FIXÉE AUX MONTANTS Model Number: ____________________ Número del modelo Numéro de modèle Date of Purchase: ____________________ Fecha de compra Date d’achat Register Online Regístrese en línea S’enregistrer en ligne www.deltafaucet.com/registerme To reference replacement parts and access additional technical documents and product info, visit www.deltafaucet.
PAGE 14
REQUIREMENTS FOR SUCCESSFUL INSTALLATION REQUISITOS PARA UNA INSTALACIÓN EXITOSA EXIGENCES À RESPECTER POUR RÉUSSIR L’INSTALLATION KNOWLEDGE BASE: Framing Plumbing • Confirm that your model will fit in intended location and plumbing fixtures are located where required before beginning installation. • Walls and sub-floor must be solid, plumb, and square. • Allow product to reach room temperature for 30 minutes before installation • Do not install in areas where temperature may drop below 32ºF (0ºC).
PAGE 15
TOOLS AND MATERIALS CHECKLIST LISTA DE VERIFICACIÓN DE HERRAMIENTAS Y MATERIALES LISTE DE VÉRIFICATION DES OUTILS ET DU MATÉRIAL REQUIS Caulk Gun Pistola para sellar Pistolet à calfeutrer Tape Measure Cinta métrica Ruban à mesurer Pencil Lápiz Crayon Safety Glasses Antiparras de seguridad Utility knife Cuchillo de uso Couteau tout usage Lunettes de sécurité MO Level Nivel Niveau Extension Bit Holder Sujetador de extensión para brocas Support pour mèche d’extension RTA R Mortar Mortero Mortier
PAGE 16
IMPORTANT: IF INSTALLING MATCHING WALL SET, refer to Wall Set Installation Manual for specific lumber sizes and placement. Additional studs will be required and need to be installed at this point. IMPORTANTE: SI INSTALA EL JUEGO DE PARED, consulte las instrucciones de instalación para el juego de pared y obtendrá los tamaños específicos y la ubicación de las maderas. Se necesitarán montantes adicionales y se deberán instalar en este punto.
PAGE 17
Required For Proper Installation Entire bottom support must be in contact with a flat level surface as shown below. IF INSTALLATION SURFACE IS NOT LEVEL, use leveling compound or mortar bed for proper installation. Requerida Para Una Instalación Correcta Todo el soporte inferior debe estar en contacto con una superficie plana y nivelada. SI LA SUPERFICIE DE LA INSTALACIÓN NO ESTÁ NIVELADA, para una instalación adecuada use compuesto nivelador o lecho de mortero.
PAGE 18
1 2 2 1 A 3 Protect bathtub finish by overturning it onto a clean, soft surface such as a drop cloth. Verify Bathtub Fit • Position bathtub as shown above. Use level (1) and square (2) to verify that it is positioned straight and square. A• Apply double sided foam tape to the apron support face that contacts the inside of the tub apron. Evenly space as shown. Bathtub bottom (3) must be in contact with a flat, level surface.
PAGE 19
3 4 Overflow Rebosadero Trop-plein 1 1 2 13 3/4" (394 mm) 1 2 Prepare Bathtub • Attach drain and overflow following manufacturer’s instructions. • Drill 3/16” clearance holes: (1) In flat area of top flanges, below lip, and centered on each stud. (2) Evenly spaced on front vertical flanges. NOTE: The drain and overflow will require at least 13 3/4" of vertical adjustment. RP293 and RP393 have been designed to fit Delta bathtubs. Do not drill holes directly into studs.
PAGE 20
5 IF THE SUBFLOOR IS NOT FLAT AND LEVEL, a mortar bed must be applied where the base will be positioned. • Apply 1” mortar bed in rectangle where tub bottom contacts subfloor, that has been mixed to a thick consistency. • Low spots in subfloor may require mortar thicker than 1”. • Place the base in the wet mortar and adjust until it is level. • Let mortar cure for 24 hours. • Proceed to the next step. SI EL CONTRAPISO NO ESTÁ PLANO Y NIVELADO, debe aplicar una capa de mortero donde colocará la base.
PAGE 21
7 If not installing matching wall set. Si no instala el juego de pared correspondiente. Si vous n’installez pas l’ensemble mural correspondant. CARE AND CLEANING We recommend that you clean your acrylic bathing product with mild detergents. Use a terry cloth towel, soft cloth, or sponge. Avoid using abrasive scrubbing pads, steel wool, or sponges. After cleaning, rinse thoroughly with water. NOTICE When using drain cleaner or clog remover, rinse thoroughly with water.
PAGE 22
10 113866 Rev.
PAGE 23
11 113866 Rev.
PAGE 24
Limited Warranty on Bathing Products This bathing product is warranted to the original consumer purchaser or commercial user, as applicable, to be free from defects in material and workmanship for the applicable period specified below: Delta® Tubs, Shower Bases, and Walls. Ten (10) years from the date of purchase by the original consumer purchaser or, for commercial users, one (1) year from the date of purchase. Delta® Glass and Frameless Shower Enclosures and Shower Doors.