Instructions

- 3 -
RS-485 Communication
Mode
Supported, including ASCII/RTU mode. Default communication format:
9600, 7, E, 1, ASCII; refer to CR#32 for details on the communication
format.
Note1: RS-485 cannot be used when connected to CPU series PLCs.
Note2: Refer to Slim Type Special Module Communications in the
appendix E of the DVP programming manual for more details on RS-485
communication setups.
*1: The unit of temperature would be displayed as 0.1°C/0.1°F. If the temperature unit is set to be
Fahrenheit, the second decimal place would not be shown.
 Control Register
CR# Address Latched Attribute Register content Description
#0 H’4064 O R
Model name
(Set up by the system)
DVP04PT-S model code= H’8A
DVP06PT-S model code = H’CA
#1 H’4065 X R/W CH1~CH4 Mode setting
b15~12 b11~8 b7~4 b3~0
CH4 CH3 CH2 CH1
Take CH1 mode (b3,b2,b1,b0) for
example.
1. (0,0,0,0): Pt100 (default)
2. (0,0,0,1): Ni100
3. (0,0,1,0): Pt1000
4. (0,0,1,1): Ni1000
5. (0,1,0,0): LG-Ni1000
6. (0,1,0,1): Cu100
7. (0,1,1,0): Cu50
8. (0,1,1,1): 0~300 Ω
9. (1,0,0,0): 0~3000 Ω
10. (1,1,1,1)The channel is
disabled.
Mode 8 and 9 are only available for
DVP04PT-S V4.16 or later and
DVP06PT-S V4.12 or later.
#2
H’4066
O R/W
DVP04PT-S:
CH1 average number
Number piece of readings used for
the calculation of “average”
temperature on CH1.
Setting range: K1~K20.
Default setting is K10.
--
DVP06PT-S:
CH1~CH6 average number
Number piece of readings used for
the calculation of “average”
temperature on CH1 ~ 6.
Setting range: K1~K20.
Default setting is K10.
#3 H’4067 O H’4067
DVP04PT-S:
CH2 average number
Number piece of readings used for
the calculation of “average”
temperature on CH2.
Setting range: K1~K20.
Default setting is K10.
#4 H’4068 O H’4068
DVP04PT-S:
CH3 average number
Number piece of readings used for
the calculation of “average”
temperature on CH3.
Setting range: K1~K20.
Default setting is K10.
#5 H’4069 O H’4069
DVP04PT-S:
CH4 average number
Number piece of readings used for
the calculation of “average”
temperature on CH4.
Setting range: K1~K20.
Default setting is K10.
#6 H’406A X R CH1 average degrees
DVP04PT-S:
Average degrees for CH1 ~ 4
DVP06PT-S:
Average degrees for CH1 ~ 6
Unit: 0.1°C, 0.01 Ω (0~300 Ω),
0.1 Ω (0~3000 Ω)
#7 H’406B X R CH2 average degrees
#8 H’406C X R CH3 average degrees
#9 H’406D X R CH4 average degrees
#10 -- X R CH5 average degrees
#11 -- X R CH6 average degrees
#12 H’4070 X R CH1 average degrees
DVP04PT-S:
Average degrees for CH1 ~ 4
DVP06PT-S:
Average degrees for CH1 ~ 6
Unit: 0.1°C, 0.01 Ω (0~300 Ω),
0.1 Ω (0~3000 Ω)
#13 H’4071 X R CH2 average degrees
#14 H’4072 X R CH3 average degrees
#15 H’4073 X R CH4 average degrees
#16 -- X R CH5 average degrees
#17 -- X R CH6 average degrees
#18 H’4076 X R Present temp. of CH1
DVP04PT-S:
Present temperature of CH 1~4
#19 H’4077 X R Present temp. of CH2