Installation & Assembly

ManualsBrandsDelta ManualsFaucet HandlesVero Lever Handles for Bathroom Faucets in Champagne Bronze

Para instalación fácil de su llave Delta

usted necesitará:

Ŗ LEER TODAS las instrucciones completamente

antes de empezar.

Ŗ LEER TODOS los avisos, cuidados, e

información de mantenimiento.

ŖPara completar el borde y la instalación de

válvulas dentro de las paredes previa a la

instalación de la llave y sus accesorios.

For easy installation of your Delta

faucet you will need:

ŖTo READ ALL the instructions completely

before beginning.

Ŗ To READ ALL warnings, care, and maintenance

information.

ŖTo complete the deck and valve rough-in prior to

installing this trim kit.

Pour installer votre robinet Delta

facilement, vous devez:

ŖLIRE TOUTES les instructions avant de débuter;

ŖLIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

Ŗ Installez le corps du robinet et terminez le

pourtour du bain avant de poser les accessories

de finition.

Model/Modelo/Modéle

T2753 & T4753

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

SILICONE

1/8" (3.17mm)

3/32" (2.38mm)

1/8" (3.17mm)

3/32"

(2.38mm)

SILICONE

ASME A112.18.1 / CSA B125.1

ICC/ANSI A117.1

TWO HANDLE ROMAN TUB TRIM

LLAVE Y SUS ACCESORIOS

PARA BAÑERA ROMANA DE DOS

MANIJAS (MANERALES)

ACCESSOIRES DE FINITION DE

ROBINET À DEUX POIGNÉES POUR

BAIN ROMAIN

9/2/10 Rev. C

65982

Summary of content (8 pages)

PAGE 1
TWO HANDLE ROMAN TUB TRIM 65982 UP LLAVE Y SUS ACCESORIOS PARA BAÑERA ROMANA DE DOS MANIJAS (MANERALES) C ACCESSOIRES DE FINITION DE ROBINET À DEUX POIGNÉES POUR BAIN ROMAIN ® ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 Model/Modelo/Modéle T2753 & T4753 Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici. SI LI C O N E You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin: 3/32" (2.
PAGE 2
Backflow Protection System Cleaning and Care Your Delta Faucet hand shower incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1/ CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly. It also incorporates a diverter mechanism that automatically diverts to the spout mode when there is a reduction in the supply pressure.
PAGE 3
Model / Modelo / Modèle T2753 RP63355Ÿ Hot Handle Assemblies Montajes manetas calientes Poignées équipées chaudes ▲Specify Finish ▲ Especifíque el Acabado ▲ Précisez le Fini RP63358Ÿ Set Screw & Button Tornillo de Presión y Vis de Calage et RP63356Ÿ Cold Handle Assemblies Montajes manetas fríos Poignées équipées à froid RP63367 Set Screw (2) Tornillo de Ajuste (2) Vis de Calage (2) RP51022 Stem Extender (2) Extensión para la espiga (2) Rallonge de tige (2) RP51021 Glide Ring (2) Aro para Deslizar (2) L
PAGE 4
A. B. T4753 1 2 3 RP40668 Diverter Assembly Ensamble del Desviador Dérivation 3 4 2 1 2 4 1 Maintenance B. Model T4753 A. If faucet leaks from spout outlet–Shut off water supplies– Replace Seats and Springs (1).* If leak persists – Shut off water supplies – Replace Stem Unit Assembly (2).* If faucet does not divert water from the spout to the hand shower, check that the lift rod (1) is securely threaded into the diverter (2). If the problem persists remove the lift rod and spout.
PAGE 5
1 T2753 2 T2753 1 3 4 1 3/32" (2.38 mm) 3/32 po 2 T4753 T4753 1 1 3 4 2 3/32" (2.38 mm) 3/32 po 2 Assemble spout (1) onto adapter (2) with gasket. Secure spout with set screw (3). Insert button (4) into set screw hole. Note: If surface is uneven, use silicone sealant under the spout. NOTE: The deck and valve rough-in must be finished before installing the trim kit. Model T2753 Unscrew the test cap (1) and discard. Model T4753 Remove set screw (1). Remove and discard test cap (2).
PAGE 6
3 A. T4753 C. 2 T4753 1 3 1 2 B. D. T4753 T4753 1 2 1 4 3 For Model T4753 Only A. Loosen set screw (1), remove finial (2) from lift rod (3) and install C. Install base (1) to nest (2) and tighten. OPTION: Use silicone B. Remove and discard the test cap and gasket (1). NOTE: This is an D. Slide hose (1) through conical nut (2). Attach hose (1) to braided under the base if deck is uneven. lift rod. Screw the lift rod until it drops down and rotates freely.
PAGE 7
4 T2753 5 7 8 5 5/64" (2 mm) 5/64 po T2753 1 6 3 9 1 1 2 T4753 4 T4753 7 8 5 5/64" (2 mm) 5/64 po 2 6 1 2 3 9 1 2 4 Model T2753 Turn faucet handles (1) all the way on. Turn on hot and cold water supplies and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Model T4753 Make sure the lift rod (1) is in the down position. Turn faucet handles (2) all the way on.
PAGE 8
6 A. B. T4753 T4753 1 2 3 1 2 For Model T4753 Only A. Pull hose (1) to its farthest extension and point it down into the B. Attach hand piece (1) to hose (2) with gasket (3) between tub. Pull the lift rod (2) up to the full on position and flush water lines for one minute. After flushing turn off water at the bath valve handles. Return the lift rod to the down position. connection. Refer to maintenance section (page 4) for correcting diverter and lift rod function. Sólo para los Modelo T4753 B.