Installation Guide

ManualsBrandsDelta ManualsBathTraditional Roman Tub Hand Held Shower in Polished Brass

ROMAN TUB HAND HELD

SHOWER AND DIVERTER

DUCHA DE MANO PARA BAÑERAS

ROMANAS Y DESVIADOR

DOUCHE À MAIN ET DÉRIVATION

POUR BAIN ROMAIN

Model/Modelo/Modéle

RP33791LHP

Series/Serie/Seria

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

•ToREAD ALLwarnings,care,andmaintenance

information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien.

SILICONE

Icons

SILICONE

Icons

SILICONE

Icons

SILICONE

Icons

5/9/13   Rev.E

46685

www.deltafaucet.com

Summary of content (8 pages)

PAGE 1
46685 ROMAN TUB HAND HELD SHOWER AND DIVERTER DUCHA DE MANO PARA BAÑERAS ROMANAS Y DESVIADOR DOUCHE À MAIN ET DÉRIVATION POUR BAIN ROMAIN Model/Modelo/Modéle RP33791LHP Series/Serie/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
▲Specify Finish/Especifíque el Acabado/Précisez le Fini RP23094▲ Base w/Gasket Base y Empaque Embase et joint RP40666 Hand Spray Support Assembly Soporte de la Regadera de Mano Support de douche à main RP19652 Nuts & Washer Tuercas y Arandela Écrous et rondelle RP46680▲ Hand Piece PIeza de Mano Douche à main RP19654▲ Sleeve Manguito Manchon RP40665 Nest Sujetador Logement RP18632▲ Transfer Valve Válvula de Transferencia Robinet de dérivation RP18627 Extender Extension Rallonge RP4
PAGE 4
1 2 4 3 Maintenance Cleaning and Care If leaks from hand piece: SHUT OFF WATER SUPPLIES. Replace Diverter Assembly (3)–Repair Kit RP19653. 1. Remove handle. Remove sleeve (1). 2. Reinstall handle. Pull on handle to remove extender (2) and diverter assembly (3) from the valve. 3. Detach handle and replace old diverter assembly (3) with a new one. 4. Reinstall handle to extender (2) and diverter assembly (3). 5.
PAGE 5
1 C. A. 3 2 3 2 18" (45.7 cm) max. 1 1- 1/2" (35mm) 1- 1/2 po (35mm) B. D. 1 1 3 2 1 1 1 1 3 2 A. SHUT OFF WATER SUPPLIES. Drill two 1-1/2" diameter holes in finished surface, one for the transfer valve and one for the spray support assembly. NOTE: The length of the braided metal hose limits the distance between the transfer valve and deck fitting. The distance between the transfer valve and deck fitting should not exceed 18" with the braided metal hose furnished. C.
PAGE 6
2 A. C. 1-5/8"—1-7/8" (41.3—47.6mm) 1 1 1 3 1 2 2 B. D. 1 2 2 1 3 4 A. Remove thin nut (1) from transfer valve (2). Install transfer valve from underside of mounting surface so that the handle stem (3) is 1-5/8" to 1-7/8" above the finished surface. Reinstall thin nut (1) to secure valve. B. Install gasket (1) and base (2). OPTION: If deck is uneven, use silicone sealant under the gasket. A. Quite la tuerca delgada (1) de la válvula de transferencia (2).
PAGE 7
3 4 A. 1 2 2 B. 3 2 1 IN LE INLE T T 1 1 4 3 From tub valves, connect hot and cold water lines to labeled inlets (1) on transfer valve. Either inlet (1) may be used for hot and cold. Use plumber tape on threaded connections. Connect tub spout (2) to remaining outlet port (3) on transfer valve. WARNING: Excessive heat during installation may damage internal components. Removal of the diverter is recommended prior to installation if excessive heat will be used. A.
PAGE 8
C. 5 A. 1 1 2 B. 1 3 2 A. Turn on water supplies. Pull hose (1) to its furthest extension, pointing it down C. Install base (1) to nest (2) and tighten. OPTION: Use silicone under the into the tub, turn the diverter handle to the hand shower position. Turn bath valve handles to the full on positions, and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Check all connections at arrows for leaks.