Instructions / Assembly

ManualsBrandsDelta ManualsAlcove Shower DoorsC500 59 in. W x 71-1/8 in. H Frameless Sliding Shower Door in Nickel with 5/16 in. (8mm) Tempered Clear Glass

STOP

PARE

• BEFORE BEGINNING, READ ALL INSTRUCTIONS WITH PARTICULAR

ATTENTION TO SAFETY INFORMATION AND TO ENSURE YOU HAVE ALL

PARTS, TOOLS AND PROTECTIVE EQUIPMENT NEEDED TO SAFELY INSTALL

YOUR UNIT.

• PLEASE DO NOT CONTACT STORE FOR REPLACEMENT PARTS

• PLEASE CONTACT 1-800-964-4850 FOR ASSISTANCE

• ANTES DE COMENZAR, LEA TODAS LAS INSTRUCCIONES PRESTANDO

ATENCIÓN ESPECIAL A LA INFORMACIÓN DE SEGURIDAD Y ASEGÚRESE DE

TENER TODAS LAS PIEZAS, HERRAMIENTAS Y EQUIPOS DE PROTECCIÓN

NECESARIOS PARA INSTALAR SU UNIDAD DE FORMA SEGURA.

• POR FAVOR, NO CONTACTE A LA TIENDA PARA SOLICITAR PIEZAS DE

REPUESTO

• POR FAVOR LLAME AL 1-800-964-4850 PARA RECIBIR ASISTENCIA

INSTALLATION GUIDE / GUÍA DE INSTALACIÓN

C500

Exposed Roller

Shower Door

5/16 inch glass (8 mm)

Rodillo expuesto

Puertas para ducha

Vidrio de 5/16 pulg. (8 mm)

CP6067583 JULY 2021

DESIGNED AND DISTRIBUTED BY LIBERTY HARDWARE MANUFACTURING CORPORATION

CAUTION:

To reduce the risk of breakage, keep corner protectors on glass while installing. Avoid contact between

shower door and metal parts and/or hard surfaces. Always ensure glass panels are placed on padded surfaces.

PRECAUCIÓN: Durante la instalación, coloque vidrio o protectores de esquinas para reducir el riesgo de romperse. Evite el

contacto entre la puerta de la ducha y las piezas metálicas y/o superficies duras. Asegúrese siempre de que los paneles de

vidrio estén colocados sobre superficies acolchadas.

NOTE:

Installation widths: 60" Tub/shower: 55-3/8"minimum – 59-3/8" maximum,

48" Shower: 43-3/8" minimum – 47-3/8" maximum.

NOTA:

Anchos de instalación: para ducha/bañera de 60" (152,40 cm): mínimo 55,375" (140,65 cm) – máximo 59,375"

(150,8 cm), ducha de 48" (121,92 cm): mínimo 43,375 (110,72 cm) – máximo 47,375" (120,33 cm).

CAUTION identifies a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury and/or

property/product damage.

IMPORTANT identifies information critical to installation,

operation, or maintenance.

NOTE indicates helpful advice to make installation, operation, or

maintenance proceed well.

ADVERTENCIA identifica situaciones potencialmente peligrosas

que, de no evitarse, podrían provocar lesiones leves o

moderadas y/o daños a la propiedad/producto.

IMPORTANTE identifica información esencial para la instalación,

funcionamiento, o mantenimiento.

NOTA indica consejos útiles para una correcta instalación,

funcionamiento o mantenimiento.

Minimum Required Clearance Heights for Installation:

For Shower: 72 Inches (182.9 cm)

For Tub: 61 Inches (154.9 cm)

Minimum Required

Installation Wall Heights

for Installation:

For Shower: 69-3/8 Inches (176.2 cm)

For Tub: 61 Inches (154.9 cm)

Minimum Sill Depth

Requirements:

2-7/8" (7.1 cm)

Alturas mínimas de separación necesarias para la instalación:

Para la ducha: 72 pulgadas (182,9 cm)

Para la bañera: 61 pulgadas (154,9 cm)

Alturas mínimas de la pared necesarias para la instalación:

Para la ducha: 59,375 pulgadas (170,08 cm)

Para la bañera: 61 pulgadas (154,9 cm)

Requisitos mínimos

de profundidad del

bordillo: 2, 875"

(7,1 cm)

Summary of content (50 pages)

PAGE 1
C500 Exposed Roller Shower Door 5/16 inch glass (8 mm) Rodillo expuesto Puertas para ducha Vidrio de 5/16 pulg. (8 mm) STOP PARE • BEFORE BEGINNING, READ ALL INSTRUCTIONS WITH PARTICULAR ATTENTION TO SAFETY INFORMATION AND TO ENSURE YOU HAVE ALL PARTS, TOOLS AND PROTECTIVE EQUIPMENT NEEDED TO SAFELY INSTALL YOUR UNIT.
PAGE 2
Required tools / Herramientas necesarias 1/8" Drill Bit Broca de 1/8" Marking Tool Herramienta de marcado 1/4" Tile Bit Broca de 1/4" para baldosas Stud Finder Detector de montantes 5/16" Drill Bit Broca de 5/16" 32 TPI 32 TPI Closed-Toe Shoes Zapatos cerrados 3' Level or longer Nivel de 3' o más largo Painters Tape Cinta de pintor 3" Deep Miter Box Caja de ingletes de 3" de profundidad 100% Silicone Sealant – Clear Sellador de silicona 100 % - Transparente Shop Vacuum Aspiradora de taller Tin Sn
PAGE 3
BEFORE YOU START NOTICE: • Tempered safety glass is stronger than normal glass but is not unbreakable. A scratch to the glass or contact with a hard surface (such as a screw head or tile/concrete floor) can cause it to break or weaken. This could, immediately or even at a later time, cause the glass panel to shatter into many small pieces without apparent cause. When it does break, it loudly explodes into thousands of smaller pieces (the smaller pieces reduce the risk of personal injury).
PAGE 4
ANTES DE COMENZAR AVISO: • El vidrio templado de seguridad es más fuerte que el vidrio normal, pero no es irrompible. Un rasguño en el vidrio o el contacto con una superficie dura (como la cabeza de un tornilloo el piso de cerámica/concreto) puede hacer que se rompa o se debilite. Esto podría, inmediatamente o incluso en el futuro, hacer que el panel de vidrio se rompa en muchos pedazos pequeños sin causa aparente.
PAGE 5
CARTON PARTS IDENTIFICATION / IDENTIFICACIÓN DE LAS PARTES See following pages for detailed component diagrams / Consulte en las páginas siguientes los diagramas detallados de los componentes A1 B1 C1 D1 E1 F1 G1 H1 I1 J1 K1 L1 M1 N1 O1 P1 Q1 R1 S1 T1 U1 V1 Top Track Dam Strip Outside Glass Panel Inside Glass Panel Hold Down Bracket Left Hold Down Bracket Right Center Guide Center Guide Screw Cover Cap ST M4 x 16 Screw Magnetic Side Jamb Magnetic Strip Magnetic Seal Blade Seal Water Diverter Sweep ST M4 x
PAGE 6
DOOR ASSEMBLY / MONTAJE DE LA PUERTA CAUTION: To reduce the risk of breakage, which may result in personal injury, property damage or product failure, DO NOT set glass panels on a hard surface or on their edge. * * * Detailed views of components on pages 7 and 8. * Las vistas detalladas de los componentes Y1 x2 D1 K1 están en las páginas 7 y 8.
PAGE 7
HARDWARE / HERRAJES P2 Y1 x2 M2 X1 x2 Outside Roller Assembly Conjunto del r odillo externo Inside Roller Assembly Conjunto del rodillo interno L2 N2 J2 O2 H2 F2 G2 K2 Q2 x4 x2 R2 Z1 x2 Collar Bracket Assembly Conjunto de soporte del collarín H1 S2 T2 G1 V1 x4 F1 E1 7
PAGE 8
HANDLES AND HARDWARE / MANGOS Y HERRAJES I1 x1 O1 x12 D2 x2 E2 x2 Screw Tornillo (ST M4 x 16) Screw Tornillo (ST M4 x 40) P1 x13 Tile Anchor Anclaje de azulejo C2 x4 Q1 x13 Acrylic Anchor Anclajes de acrílica A2 T1 Hex Wrench Included Llave Allen incluidas (2.
PAGE 9
CAUTION: To avoid personal injury or property damage, identify components and read all instructions before installing. RECAUCIÓN: Para evitar lesiones o daños a la propiedad, identifique los componentes y lea todas las instrucciones antes de P la instalación. IMPORTANT: Incorrect measurement may prevent proper door closure. Double-check measurement. Before beginning installation, verify the door assembly will fit within the horizontal opening of the shower enclosure.
PAGE 10
2 Locating Mounting Stud Position IMPORTANT: Using a stud finder, ensure that the wall on each side of the enclosure has a stud in the location shown. A stud in this location must be identified to support the top track in order to proceed with the installation. This system must be installed into a stud. If you do not have a stud in the area shown this door CAN NOT be installed, call Delta Shower Doors Customer Care Team at 1-800-964-4850.
PAGE 11
CAUTION Wear safety glasses and cut resistant gloves with non-slip grip when drilling or cutting to avoid risk of injury. 4a PRECAUCIÓN Use gafas protectoras y guantes anticorte y antideslizantes al taladrar o cortar para evitar el riesgo de lesiones. Curved Threshold Enclosures S1 IMPORTANT: The wall bracket template (S1) must sit flat against the shower wall and bottom threshold ledge. The area where the wall and bottom threshold meet may be curved.
PAGE 12
4c For Acrylic Enclosures Only Push in the center of the acrylic wall anchors (Q1) and squeeze clips together. Insert acrylic wall anchors (Q1) into holes. If needed, a rubber mallet can be used to insert acrylic anchors (Q1). If needed, use drill to slightly enlarge the opening of the hole. NOTE: Acrylic wall anchors (Q1) MUST be used as an added support. Repeat steps 4a-4c for other end of enclosure.
PAGE 13
5b For Tile Enclosures Only Insert tile anchors (P1) in each hole location. The tile anchors (P1) should fit securely into the holes. NOTE: Tile anchors (P1) MUST be used as an added support. Repeat steps 5a-5b for other end of enclosure. Solo para recintos de baldosas: Inserte los anclajes para baldosas (P1) en la ubicación de cada orificio. Los anclajes para baldosas (P1) deben encajar firmemente dentro de los orificios. NOTA: Los anclajes para baldosas (P1) se DEBEN utilizar como soporte adicional.
PAGE 14
7 Place collar wall bracket (S2) into position. Secure to side enclosure with ST M4 x 40 screws (O1). Hand tighten until fully secure. Repeat for remaining collar wall bracket (S2). S2 Coloque el soporte de pared de collarín (S2) en su posición. Fíjelo a la parte lateral de la cabina con tornillos ST M4 x 40 (O1). Ajuste a mano hasta que quedé completamente firme. Repita este paso con el soporte de pared del collarín restante (S2).
PAGE 15
9 Top track / Riel superior Using measurement “A” from previous step, subtract 1/4" to calculate measurement “B”. Measurement “A” ” “B - 1/4" A1 = ________ f measurement “B” Using a marking tool, mark distance “B” on the top track (A1). For any questions regarding this step please contact the Delta Shower Doors Customer Care Team at 1-800-964-4850. Utilizando la medida “A” del paso anterior, sustraiga 1/4" para calcular la medida “B”.
PAGE 16
11 Remove BOTH decorative covers (P2) from EACH inside roller assemblies (Y1). P2 Retire AMBAS cubiertas decorativas (P2) de CADA conjunto de rodillo interno (Y1). 2 1 Y1 P2 12 Insert BOTH inside roller assemblies (Y1) into INNER CHANNEL of top track (A1). A1 Inserte AMBOS conjuntos de rodillo interno (Y1) en el CANAL INTERNO del carril superior (A1).
PAGE 17
13 A1 T2 Slide collars (T2) onto each end of top track (A1). Ensure that the M5 x 16 set screws (R2) (the longer set screws), are facing toward the inside of the enclosure engaging the recessed portion of the top track (A1). Deslice los collarines (T2) a cada extremo del carril superior (A1). Asegúrese de que los tornillos de ajuste M5 x 16 (los tornillos de ajuste más largos [R2]) estén dirigidos hacia el interior de la cabina e introducidos en la parte cóncava del carril superior (A1).
PAGE 18
15 Secure collars (T2) by hand tightening hex head screws (Q2, R2) using supplied 2.5 mm hex wrench (T1). Fije los collarines (T2) apretando los tornillos hexagonales (Q2, R2) con la llave hexagonal de 2.5 mm (T1) incluida. T1 T2 T1 T2 16 Dam Strip Installation Using a measuring tape, measure distance between the side walls at sill location as shown in Figure 16. This will be measurement “C”.
PAGE 19
17 Dam Strip Barrera Using measurement “C” from previous step, subtract 7/8" to calculate measurement “D”. Measurement “C” - 7/8" = ________ f measurement “D” Using a marking tool, mark distance “D” on the dam strip (B1). For any questions regarding this step please contact the Delta Shower Doors Customer Care Team at 1-800-964-4850. ” “D Utilizando la medida “C” del paso anterior, sustraiga 3/8" para calcular la medida “D”.
PAGE 20
19 Apply a thick line of silicone to underside of dam strip (B1) as shown in Figure 19. Aplique un cordón denso de silicona en la parte inferior de la barrera (B1) como se muestra en la Figura 19. B1 20 Using mark created from step 2, place dam strip (B1) into position 1-1/2" in front of the center of the stud. Ensure each edge of the dam strip (B1) is 7/16" from the side wall. For any questions regarding this step please contact the Delta Shower Doors Customer Care Team at 1-800-964-4850.
PAGE 21
CAUTION Wear safety glasses and cut resistant gloves with non-slip grip when drilling or cutting to avoid risk of injury. 21a PRECAUCIÓN Use gafas protectoras y guantes anticorte y antideslizantes al taladrar o cortar para evitar el riesgo de lesiones. Curved Threshold Enclosures F1 IMPORTANT: The left and right hold down brackets (E1, F1) must sit flat against the shower wall and bottom threshold ledge. CAUTION The area where the wall and bottom threshold meet may be Use curved.
PAGE 22
Center Guide Installation Using a measuring tape, locate the center of the installed dam strip (B1). Using a marking tool, mark the center of the dam strip (B1). Instalación de la guía central Utilizando una cinta métrica, ubique el centro de la barrera de contención de agua instalada (B1). Utilizando una herramienta de marcado, marque el centro de la barrera de contención de agua (B1).
PAGE 23
Para evitar el riesgo de lesiones o daños al producto, asegúrese de perforar en los montantes. 24a CAUTION Wear safety glasses and cut resistant gloves with non-slip grip when drilling or cutting to avoid risk of injury. PRECAUCIÓN Use gafas protectoras y guantes anticorte y antideslizantes al taladrar o cortar para evitar el riesgo de lesiones. For Acrylic Enclosures Only B1 After removing center guide (G1), drill a 1/8" pilot hole at the location marked in the previous step.
PAGE 24
Para evitar el riesgo de lesiones o daños al producto, asegúrese de perforar en los montantes. 25a CAUTION Wear safety glasses and cut resistant gloves with non-slip grip when drilling or cutting to avoid risk of injury. PRECAUCIÓN Use gafas protectoras y guantes anticorte y antideslizantes al taladrar o cortar para evitar el riesgo de lesiones. For Tile Enclosures Only B1 After removing center guide (G1), drill a 1/4" hole at the location marked in the previous step using a tile bit.
PAGE 25
26 Apply beads of silicone to underside of center guide (G1) as shown in Figure 26. Aplique gotas de silicona en la parte de abajo de la guía central (G1), como se muestra en la figura 26. G1 27 I1 Re-place center guide (G1) onto sill. Use drill to start ST M4 x 16 screw (I1) into the anchor. Next, use a screwdriver to hand tighten until secure. G1 Vuelva a colocar la guía central (G1) sobre el bordillo. Utilice la broca para abrir camino a los ST M4 x 16 tornillo (I1) hacia los anclaje.
PAGE 26
28 Using silicone, install center guide screw cover cap (H1) over center guide screw. Utilizando silicona, instale la cubierta del tornillo de la guía central (H1) sobre el tornillo de la guía central. H1 G1 2 H1 1 CAUTION Risk of injury or product damage. During installation, tempered glass should not come in direct contact with metal parts or hard surfaces (such as tile/concrete flooring) or it may shatter. PRECAUCIÓN CAUTION Riesgo de lesión o daño del producto.
PAGE 27
Inner Door Glass Panel Assembly/Installation -- Ensamblaje/instalación del panel de vidrio de la puerta interior 30 Shower Head on the Right Cabezal de ducha a la derecha Text Trans IMPORTANT During installation and use, the inner panel should be closest to the shower head. IMPORTANTE Durante la instalación y uso, el panel interno debe estar más cerca del mango ade ducha.
PAGE 28
tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. CAUTION PRECAUCIÓN Risk of injury or product damage. During installation, tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. Riesgo de lesión o daño del producto.
PAGE 29
*Inside Enclosure* 33 *Dentro del recinto* R1 From inside of enclosure, use smaller wrench of the multi wrench tool (R1) provided to remove roller nut (M2) and larger wrench to remove roller adjustment bushing (L2) from rolling bearing (O2). Repeat for remaining inside roller assembly (Y1).
PAGE 30
CAUTION Risk of injury or product damage. During installation, tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. 35 PRECAUCIÓN Riesgo de lesión o daño del producto. Durante la instalación el vidrio templado no debe entrar en contacto con partes metálicas ni superficies duras (como azulejos de cerámica o pisos de hormigón) ya que podría romperse.
PAGE 31
CAUTION Risk of injury or product damage. During installation, tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. *Inside Enclosure* 37 *Dentro del recinto* PRECAUCIÓN Riesgo de lesión o daño del producto.
PAGE 32
tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. CAUTION PRECAUCIÓN Risk of injury or product damage. During installation, tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. Riesgo de lesión o daño del producto.
PAGE 33
40 Remove decorative cover (K2) from outside roller assembly (X1). Next, use provided multi wrench tool (R1) to remove roller nut (G2) and roller adjustment bushing (F2) from outside roller assembly (X1). Repeat for remaining outside roller assembly (X1). NOTE: Ensure roller washer (H2) is not removed from the outside roller assembly (X1). 1 K2 R1 2 R1 Retire la cubierta decorativa (K2) del conjunto del rodillo externo (Y1).
PAGE 34
CAUTION Risk of injury or product damage. During installation, tempered glass should not come in contact with metal parts or hard surfaces (tile/concrete flooring) or it may shatter. Gaskets or bushings must always be used between glass and metal. 42 PRECAUCIÓN Riesgo de lesión o daño del producto. Durante la instalación el vidrio templado no debe entrar en contacto con partes metálicas ni superficies duras (como azulejos de cerámica o pisos de hormigón) ya que podría romperse.
PAGE 35
2 44 Ensure that the key of the outside roller bearing (J2) is pointed downwards such that it is engaged in the upper slot of the top track (A1) as shown in Figure 44. NOTE: Ensure that the key of the outside roller bearing (J2) is not making contact with the top track (A1). J2 Asegúrese de que la chaveta del cojinete del rodillo externo (J2) quede dirigida hacia abajo de manera que quede introducida en la ranura superior del carril superior (A1) como se muestra en la figura 44.
PAGE 36
2 46 Recheck and ensure that the key of the outside roller bearing (J2) is pointed downwards such that it is engaged in the upper slot of the top track (A1) as shown in Figure 46. NOTE: Ensure that the key of the outside roller bearing (J2) is not making contact with the top track (A1).
PAGE 37
48 Installing Magnetic Side Jambs Place magnetic seal (L1) onto the outside edge of the outer glass panel (C1) furthest from the shower head. As shown in Figure 48. Seperate magnetic seal (L1) from magnetic strip (K1). Remove all bottom corner protectors from both inside and outside glass panels. NOTE: Ensure bottom water diverter sweep (N1) ends are pressed firmly onto glass.
PAGE 38
50 Carefully close outer door glass panel (C1). Next, using a marking tool, mark the top and bottom locations of the inner edge of the magnetic side jamb (J1). 1 Cierre cuidadosamente el panel de vidrio externo (C1). Luego, utilizando una herramienta de marcado, marque el borde interno de la jamba magnética lateral (J1). C1 *Inside Enclosure* *Interior de la cabina* 1 J1 2 51 L1 J1 1 1 Carefully open outer door glass panel (C1). Remove magnetic side jamb (J1) from magnetic seal (L1).
PAGE 39
52 Curved Threshold Enclosures If there is a radius at the bottom where the side wall meets the sill, mark the bottom of the magnetic side jamb (J1) where the side wall begins to curve as shown in Figure 52. Use a saw and miter box to cut off this length from the magnetic side jamb (J1) and the magnetic strip (K1). Repeat for other side.
PAGE 40
54 Re-align magnetic side jamb (J1) with mark made in step 50 and tape into place. Vuelva a alinear la jamba magnética lateral (J1) con la marca realizada en el paso 50 y fije con cinta. J1 *Inside Enclosure* *Dentro del recinto* J1 55 Using a marking tool, mark location of all four screw holes for magnetic side jamb (J1). Repeat steps 48-55 for other end of enclosure using the outer edge of inner glass panel (D1). For acrylic enclosures, proceed to steps 56a-57a.
PAGE 41
Para evitar el riesgo de lesiones o daños al producto, asegúrese de perforar en los montantes. 56a CAUTION 1/8" Wear safety glasses and cut resistant gloves with non-slip grip when drilling or cutting to avoid risk of injury. 1 PRECAUCIÓN Use gafas protectoras y guantes anticorte y antideslizantes al taladrar o cortar para evitar el riesgo de lesiones. For Acrylic Enclosures Only After removing magnetic side jamb (J1), drill a 1/8" pilot hole at each location marked.
PAGE 42
Para evitar el riesgo de lesiones o daños al producto, asegúrese de perforar en los montantes. 56b CAUTION Wear safety glasses and cut resistant gloves with non-slip grip when drilling or cutting to avoid risk of injury. PRECAUCIÓN Use gafas protectoras y guantes anticorte y antideslizantes al taladrar o cortar para evitar el riesgo de lesiones. For Tile Enclosures Only After removing magnetic side jamb (J1), drill a 1/4" hole at each location using a tile bit.
PAGE 43
58 Reposition magnetic side jamb (J1). Use drill to start the ST M4 x 40 screws (O1) into the anchors. Next, use a screwdriver to hand tighten until secure. 1 Vuelva a colocar la jamba magnética lateral (J1). Utilice el taladro para comenzar a introducir los tornillos ST M4 x 40 (O1) en los anclajes. Luego, utilice un destornillador para apretarlos a mano y asegurarlos completamente. 2 J1 O1 1 3 59 K1 Install inner magnetic strip (K1) into magnetic side jamb (J1).
PAGE 44
60 V1 Install a magnetic side jam cover (V1) to the top of magnetic side jamb (J1). Repeat for other end of enclosure. NOTE: Silicone may be used to install magnetic side jamb covers (V1). J1 Instale una cubierta de jamba magnética lateral (V1) en el extremo superior de la jamba magnética lateral (J1). Repita el proceso para el otro extremo de la cabina. NOTA: Puede utilizar silicona para instalar las cubiertas de las jambas magnéticas laterales (V1). CAUTION Risk of injury or product damage.
PAGE 45
62 Door Adjustment (Optional) (continued) Using smaller wrench on provided adjustment wrench (R1), hand tighten nut until fully secure. Reinstall decorative covers. NOTE: Outside roller assembly shown (also applies to the inside roller assembly). Ajuste del conjunto de rodillo (continuación) Utilizando una llave más pequeña de la herramienta de llave múltiple (R1), ajuste la tuerca hasta que quede completamente firme. Vuelva a colocar la cubierta decorativa.
PAGE 46
64 1 Outside Glass Panel Blade Seal Installation 3 " /4 4-3 Using tin snips, trim off 4-3/4" from top and 5/8" from the bottom of the blade portion of the blade seal (M1). as shown in Figure 64. Install blade seal (M1) to the inside edge of the OUTSIDE GLASS PANEL (C1). For best water retention, ensure that the bottom edge of blade seal (M1) is in contact with the top of center guide (G1). Ensure blade portion of the blade seal (M1) is oriented towards the enclosure.
PAGE 47
66 C2 1 On the interior of outside roller glass panel (C1), install handle bushings (C2), inside handle pull (A2) and handle screws (E2). On exterior of outside roller glass panel (C1), install handle bushings (C2) and outside handle pull (B2). Hand tighten handle screws (E2) to secure and install handle screw covers (D2). IMPORTANT: Ensure handle bushings (C2) are placed on each side of glass. Repeat for inside roller glass panel (D1).
PAGE 48
Complete. Completa.
PAGE 49
TROUBLESHOOTING C AUTION: Do Not force the door panels to move as doing so may result in breakage and risk of injury. If the following steps do not resolve the associated symptoms or for any questions, call Delta Shower Doors Customer Care Team at 1-800-964-4850. Symptom: Operation Recommended Action 1. Sliding door panel is difficult to move. . Ensure that magnetic seal and blade seal on door panel does not contact bottom sill. a b.
PAGE 50
SOLUCIÓN DE PROBLEMAS ATENCIÓN: No fuerce el panels de puerta para moverlo ya que podría romperse y ocasionar lesiones. Si los siguientes pasos no resuelven los síntomas asociados o si tiene alguna pregunta, llame el equipo de atención al cliente de Delta Shower Doors al 1-800-964-4850. Síntoma: Funcionamiento (abrir/cerrar) Acción recomendada 1. El panel de puerta corrediza se mueve con dificultad. a.